Instruction manual

64 ZVC265-001_v02
Preparing the vacuum cleaner
for operation
1
Press the side button on the end of the suction hose.
2
Place the end of the suction hose in the vacuum cleaner.
You should hear a distinctive click, if you do it right.
3
Attach the other end of the hose (the handle) to the
suction tube.
4
Adjust the length of the telescopic suction tube by sliding
the slider according to the arrow and pull out/ pull the tube
together.
5
Assemble the proper nozzle or brush to the other end of
the suction tube.
6
Use combination carpet & oor brush for vacuuming both
hard surfaces and carpets. To clean hard surfaces – wooden
oors, plastic oors, ceramic tiles etc. pull out the brush by
pressing the switch on the combination brush according
to the gure . Retract the brush when vacuuming
carpets (set the switch in “ ”).
7
Pull the plug and cord (3) out of the vacuum cleaner.
 Whilepullingoutthecord,payattentiontothe
yellowstripewhichsignalstheendofthecord.
Furtherattempts(pullingoncord)mayresultin
damagingthecord.
8
Plug in the appliance.
Before turning the vacuum cleaner on, check whether the
CYKLON dust container is installed in the chamber of the
vacuum cleaner, and whether the inlet and outlet lters are
installed in the vacuum cleaner.
9
Switch on the vacuum cleaner by pressing the “on/off”
button (7).
10
The vacuum cleaner is equipped with a suction power
regulation control. The power is controlled by means of
a knob.
11
Turning the knob according to the label increases or
respectively decreases the suction power.
Filter disassembly
Before changing the lters make sure that the vacuum cleaner
is switched off and unplugged from the mains supply.
INLET FILTER CONE
It is necessary to clean the inlet lter cone from time to time.
1
Remove the CYKLON dust container and empty it
according to paragraph (F).
2
Release the fastening of the EPA basic lter (14) and
remove it from the CYKLON dust container.
3
Press the button situated on the CYKLON dust container
and open the bottom of the container.
4
Turn the inlet lter cone (17) clockwise.
5
Remove the inlet lter cone from the CYKLON dust
container.
B
C
6
If the inlet lter cone (17) is dirty, it may be rinsed
with running water. Remember to dry the cone before its
reinstallation.
 Pay attention to the gasket placed on the
bottomoftheconecollar.Donotloseit.
7
Place a new/rinsed inlet lter cone into the socket in
such a way that the two protrusions placed on the collar are
situated under the fastening in the body of the container.
8
The cone should be pressed tightly and turned to the
limit counterclockwise. A characteristic click noties about
a proper installation.
9
Snap the bottom of the CYKLON dust container.
10
Place the EPA basic lter (14). Pay attention so that the
two protrusions on the bottom part of the EPA basic lter (14)
nd their way into the holes of the dust container.
11
Place the CYKLON dust container in the chamber of the
vacuum cleaner. A characteristic click noties about a proper
installation.
BASIC EPA FILTER & FOAM FILTER
It is necessary to clean the basic EPA lter from time to time,
as it is contaminated with dust.
●
Uninstall the CYKLON dust container and empty it
according to paragraph (F).
1
Release the fastening of the EPA basic lter (14) and
remove it from the CYKLON dust container.
2
Remove the foam lter (15). If the foam lter (15) is dirty,
it may be washed with running water. Remember to dry it off
before reinstalling the lter.
The main function of the foam lter (15) is protecting the
basic EPA lter (14) from excessive dirt.
 Duetosafetyreasonsitisforbiddentoinstall
awetordamagedfoamlter(15).
●
Clean the pleads of the basic EPA lter (14), if any of
them are damaged, the lter denitely must be replaced.
If the basic EPA lter (14) is dirty, it may be washed with
running water. Remember to dry it off before reinstalling
the lter.
 Duetosafetyreasonsitisforbiddentoinstall
awetordamagedbasicEPAlter(14).
●
Place the foam lter back into its place.
3
Put the new/rinsed EPA basic lter (14) back in its place
– pay attention to put the two protrusions in the bottom part
of the EPA basic lter (14) in the holes of the dust container.
A characteristic click noties about a proper installation.
4
Place the CYKLON dust container with the installed
basic EPA lter (14) in the chamber of the vacuum cleaner.
A characteristic click noties about a proper installation.
D