User manual

35
GW17-051_v02
Structure of the kettle (Fig. A)
1
Control light
2
Kettle body
3
Spout
4
Lid release button
5
Lid
6
Handle
7
Water level indicator
8
On/Off (I-0) switch
9
Supplying cord
10
Storage space for the connecting cord
11
Anti-deposit lter
12
Base
Preparation of the electric kettle for operation
 Before the rst use, wash the kettle inside
(for washing instructions see “Cleaning and
maintenance”),llitwithwateruptothe“max”
level,andletitboilfourtimes(usefreshwater
eachtime)andwashagain.
Operating instructions
of the electric kettle (Fig. B)
1
Press the lid button (4) – the kettle lid will open.
2
Place the lter (11) in the kettle – if it was taken out
before.
3
Fill the kettle up with the desired amount of water (the
level is visible on the indicator (7)).
 Donotboilthewaterifitisbelowtheminimum
level or beyond the maximum level on the
indicator(7).
4
Close the lid.
5
Place the kettle on the power base (12).
6
Put the plug of the connecting cord into a mains socket
with an earth pin – the upper part of the kettle body will
light up.
7
Turn on the ketttle by pressing the switch button into
position I – the indicator light will come on.
8
The kettle switches off automatically when the water
has reached the boiling point, the lever switch returns to its
starting position – the light comes off.
If further use of the kettle is anticipated, it is not necessary
to remove the plug of the connecting cord from the power
socket.
 Becarefulnottollupwithwaterbeyondthe
nominalcapacitywhenpouringwaterintothe
kettle.
The rising of the water level in the kettle is delayed in relation
to the speed of pouring the water. It is caused by the lter
slowing down the speed of the ow. This can be prevented by
pouring the last portions of water extremely carefully before
the water reaches the maximum level on the indicator.
In the event that an empty kettle is switched on, it will be
switched off by a thermal device automatically.
In order to switch the kettle on again after it has cooled down
(approx. 15 minutes), take it off the base, replace it and
switch the kettle on by pressing the lever (8). The cooling
down of the kettle can be accelerated by puring cold water
into the kettle.
Cleaning and maintenance (Fig. C)
 Alwayscleanacoldkettle!
1
Remove the plug of the connecting cord from the power
socket.
2
Take out the lter (11).
3
Clean the outside surfaces with a soft cloth moistened
with washing-up liquid.
In order to remove the build-up of hard water lm from the
outside and inside walls of the kettle, wipe them with a cloth
moistened with vineger.
4
Rinse the kettle with fresh water.
Filter replacement – descaling
In the event that scale builds up on the bottom of the kettle,
it needs to be removed. 6% or 10% vinegar is used for this
purpose.
Open the lid
●
(4).
Take out the lter
●
(12).
Wash the lter under running water.
●
Pour in 0.5 l of vinegar and switch on the kettle
●
(8).
Boil the vinegar and leave in the kettle for about 30
●
minutes.
Pour the vinegar out and rinse the kettle with fresh
●
water.
Fill the kettle up with fresh water, boil the water and pour
●
it out after is has boiled.
Repeat the above procedure if there still is scale on the
●
bottom.
When the procedure is nished, replace the ter
●
(11) in
the kettle, following the procedure of taking the lter out
in reverse order.
 Negligenceindescalingthekettlemayresults
initsdamage.