MODEL NO: ZE-MC1 72 1-DIN DVD-MONICEIVER WITH MOTORIZED 7" LCD DISPLAY INSTRUCTION MANUAL ZE-MC172 Manual D+E-CS3.indd 1 06.09.
INHALTSVERZEICHNIS 1. SICHERHEITSHINWEISE ................................................................................... 6-7 2. BEDIENELEMENTE ......................................................................................... 8-12 BEDIENTEIL .............................................................................................................8-10 LCD-DISPLAY ............................................................................................................. 11 TOUCHSCREEN .......
DEUTSCH VERKEHRSDURCHSAGE (TA) .................................................................................... 28 REGIONAL (REG) ........................................................................................................ 28 STEREO/MONO (MONO) ............................................................................................ 28 8. DVD-WIEDERGABE ....................................................................................... 29-36 EINLEGEN UND AUSWERFEN EINER DISC ........
ZE-MC172 Vielen Dank für den Kauf dieses ZENEC-Produktes! Mit dem Kauf des ZE-MC172 haben Sie sich für ein technisch ausgereiftes Produkt entschieden, das Ihnen durch die Verwendung von hochwertigen Materialien und Bauteilen eine lange Lebensdauer garantiert. Bei dem ZE-MC172 von ZENEC handelt es sich um einen 1-DIN DVD-Receiver mit motorbetriebenem 7"/16:9 Bildschirm.
DEUTSCH GERÄTE-FEATURES INTEGRIERTER DVD/CD/MP3/WMA-PLAYER ■ Wiedergabe von CD, CD-R/RW, MP3, WMA, OGG, DVD, DVD-R/RW, DVD+R/RW, DVDMP3, VCD, SVCD, DIVX5, MPEG 4, JPEG und Picture CD ■ Regional Code 2 ■ Integrierter Dolby Digital Decoder ■ Elektronisches (ESP) und mechanisches Anti-Shock System ■ Last-Playback-Memory Funktion MOTORBETRIEBENER LCD MONITOR ■ Voll motorunterstützter, hochwertiger 7"/16:9 Bildschirm mit Touchscreen-Steuerung ■ Hohe Leuchtdichte 450cd/m2 ■ Hohe Auflösung 1440 x 234 (336'960 Pix
1. SICHERHEITSHINWEISE 1. Dieses Gerät ist nur für den Betrieb an einem Bordnetz mit +12V (DC) und Minus gegen Masse geeignet. 2. Bedienen Sie das Gerät nur so, wie es in der Bedienungsanleitung beschrieben wird. Alles andere kann zum Erlöschen Ihres Garantieanspruches führen. 3. Zerlegen oder modifizieren Sie das Gerät nicht. Dies kann zu einer Beschädigung des Gerätes führen und Ihr Garantieanspruch erlischt dadurch.
DEUTSCH 9. Gemäß den in den verschiedenen Ländern der EU geltenden Verkehrsvorschriften, darf ein Monitor der in Sichtweite des Fahrers montiert ist während der Fahrt nicht betrieben werden, da er den Fahrer vom Verkehrsgeschehen ablenkt. Beachten Sie unbedingt die geltenden Vorschriften in Ihrem Land, da ansonsten Regressansprüche von der Kfz Versicherung geltend gemacht werden können. Achten Sie zusätzlich darauf, dass die Lautstärke in Ihrem Fahrzeug nur so hoch ist, dass Sie Außengeräusche, wie z.
2. BEDIENELEMENTE BEDIENTEIL bq bo bp bn bm 1 2 4 3 5 6 7 9 bl bu cl bs br bm 1 2 4 3 5 6 7 cm bt 8 9 bl 8 ZE-MC172 Manual D+E-CS3.indd 8 06.09.
DEUTSCH 1. POWER-Taste bzw. Drehregler ■ Drücken Sie die POWER-Taste, um das Gerät einzuschalten. Halten Sie die Taste etwas länger gedrückt, um das Gerät wieder auszuschalten. ■ Betätigen Sie den Drehregler, um die Lautstärke entsprechend einzustellen und halten Sie anschließend die POWER-Taste für 2 Sekunden gedrückt, bis ein kurzer Signalton zu hören ist, um die von Ihnen eingestellte Lautstärke zu speichern. 2. IR-Sensor (Fernbedienung) ■ Empfängt die Signale der IR-Fernbedienung. 3.
12. INFO-Taste ■ Drücken Sie die INFO-Taste, um während der Wiedergabe einer Disc die Wiedergabeinformationen auf dem Monitor anzuzeigen. ■ Halten Sie die INFO-Taste gedrückt, um das Menü zur Bildeinstellung aufzurufen. 13. ANGLE(−)-Taste ■ Drücken Sie die ANGLE(−)-Taste, um den Neigungswinkel des Bildschirms schrittweise zu verringern. ■ Halten Sie die ANGLE(−)-Taste gedrückt, um den Neigungswinkel des Bildschirms stufenlos zu verringern. 14.
DEUTSCH LCD-DISPLAY 2 345 1 6 7 8 1. Hauptanzeige ■ Anzeige der Zeit, Sendefrequenz des eingestellten Radiosenders und je nach Wiedergabemodus andere Informationen. 2. PTY-Indikator (PTY) ■ Leuchtet auf, wenn “PTY“ aktiviert ist. 3. TP-Indikator (TP) ■ Leuchtet auf, wenn “TP“ aktiviert ist. 4. TA-Indikator (TA) ■ Leuchtet auf, wenn “TA“ aktiviert ist. 5. AF-Indikator (AF) ■ Leuchtet auf, wenn “AF“ aktiviert ist. 6. STEREO-Indikator ■ Leuchtet auf,wenn ein Radiosender in Stereo empfangen wird. 7.
TOUCHSCREEN Der Bildschirm des Gerätes ist in verschiedene Bereiche aufgeteilt, um die Bedienung per Touchscreen zu erleichtern. Area A Area F Area B Area C Area D Area E Bereich A: ■ Berühren Sie Bereich A, um das Hauptmenü des Gerätes aufzurufen. Bereich B: ■ Berühren Sie Bereich B, um die Wiedergabeinformationen einer DVD aufzurufen. Bereich C: ■ Berühren Sie Bereich C, um das vorherige Kapitel einer DVD auszuwählen. Bereich D: ■ Berühren Sie Bereich D, um das nächste Kapitel einer DVD auszuwählen.
DEUTSCH Remote Control 3. DIE FERNBEDIENUNG Remote Control DIE EINZELNEN TASTEN DER FERNBEDIENUNG 2 ,2 1 ,1 ,3 3 ,4 4 6 ,6 7 ,7 8 ,8 bl ,10 bm ,11 bo ,13 bp ,14 bq ,15 bu ,19 cl ,20 co ,23 cp ,24 cs ,27 ct ,28 ,5 5 ,9 9 bn ,12 ,16 br ,17 bs bt ,18 cm ,21 ,22 cn ,25 cq cr ,26 1. POWER-Taste ■ Drücken Sie die POWER-Taste, um das Gerät ein- bzw. auszuschalten. Name Ref Signal Function # 2. OPEN-Taste ■ Drücken Sie die OPEN-Taste, um den Bildschirm herauszufahren bzw. einzufahren.
7. VOL(-)-Taste ■ Drücken Sie die VOL(-)-Taste, um die Lautstärke zu verringern. 8. INFORMATION-Taste ■ Drücken Sie die INFORMATION-Taste, um die Wiedergabeinformationen anzuzeigen. 9. (-/--)-Taste ■ Drücken Sie die (-/--)-Taste, um die GOTO Suchfunktion für VCD/DVD aufzurufen. 10. STOP/BAND-Taste ■ Drücken Sie die STOP/BAND-Taste, um die Wiedergabe einer CD/DVD zu stoppen. ■ Drücken Sie die STOP/BAND-Taste, um im Tuner Modus zwischen AM und FM zu wählen. 11.
DEUTSCH 21. NEXT-Taste ■ Drücken Sie die NEXT-Taste, um zum nächsten Kapitel/Track einer Disc zu springen. ■ Drücken Sie die NEXT-Taste, um einen empfangbaren Sender eines Frequenzbandes durch Erhöhen der Frequenz auszuwählen. 22. PREVIOUS-Taste ■ Drücken Sie die PREVIOUS-Taste, um zum vorherigen Kapitel/Track einer Disc zu springen. ■ Drücken Sie die PREVIOUS-Taste, um einen empfangbaren Sender eines Frequenzbandes durch Verringern der Frequenz auszuwählen. 23.
4. BEDIENUNG UND HANDHABUNG DES MONITORS ÖFFNEN UND SCHLIESSEN DES MONITORS ■ Drücken Sie die OPEN-Taste [ ] auf dem Bedienteil des Gerätes oder die OPEN-Taste [ ] auf der Fernbedienung um den Bildschirm herauszufahren bzw. einzufahren. AUTOMATISCHES ÖFFNEN DES MONITORS ■ Wenn Sie die “TFT Auto Open“ Funktion aktiviert haben, öffnet sich der Bildschirm automatisch, sobald das Gerät eingeschaltet wird.
DEUTSCH BILDSCHIRMEINSTELLUNGEN ■ Im “DVD”, “iPOD” und “TUNER” Modus können Sie nur die Helligkeit (Brightness) des Bildes einstellen. ■ Wenn Sie sich im “AUX” oder “CAMERA”“ Modus befinden, können Sie Farbe, Kontrast und Farbton (nur NTSC) des Bildes einstellen. ANSCHLUSS DER HANDBREMSE ■ Wenn Sie das “PRK SW” Anschlusskabel entsprechend angeschlossen haben, können Sie die “Video” Wiedergabefunktion nur nutzen, wenn das Fahrzeug steht bzw. wenn die Handbremse angezogen ist.
5. ALLGEMEINE BEDIENUNG EIN- UND AUSSCHALTEN DES GERÄTES ■ Drücken Sie die POWER-Taste, um das Gerät einzuschalten. ■ Halten Sie die POWER-Taste gedrückt, um das Gerät wieder auszuschalten. Der Bildschirm schließt sich anschließend wieder automatisch. AUSWAHL EINER WIEDERGABEQUELLE ■ Drücken Sie die SRC-Taste auf der Fernbedienung oder die SRC-Taste auf dem Bedienteil, um zwischen den verschiedenen Programmquellen in folgender Reihenfolge zu wählen.
DEUTSCH 3. Verändern des Wertes eines Menüpunktes: ■ Drücken Sie eine der [] / []-Tasten auf der Fernbedienung, betätigen Sie den Drehregler (POWER) auf dem Bedienteil oder berühren Sie das entsprechende Icon auf dem Bildschirm, um den Wert des ausgewählten Menüpunktes zu verändern. 4.
EINGABE EINES SICHERHEITSCODE ■ Um das Gerät vor einem Diebstahl und der darauffolgenden unbefugten Verwendung zu schützen, besteht die Möglichkeit einen vierstelligen Sicherheitscode selbst festzulegen und einzugeben. ■ Wird das Gerät dann länger als 40 Sekunden von der Spannungsversorgung getrennt, ist es nötig diesen vierstelligen Sicherheitscode einzugeben, um die Betriebsbereitschaft des Gerätes wiederherzustellen.
DEUTSCH 6. SYSTEMEINSTELLUNGEN HAUPTMENÜ ■ Sie haben drei verschiedene Möglichkeiten das Hauptmenü aufzurufen: 1. Drücken Sie den SMART-DIAL Drehknopf auf dem Bedienteil. 2. Drücken Sie die MENU-Taste auf der Fernbedienung. 3. Berühren Sie Bereich A des Touchscreens. 1 2 3 4 5 6 7 1 Berühren Sie das Icon, um in den Tuner-Modus zu gelangen. 2 Berühren Sie das Icon, um in den CD/DVD-Modus zu gelangen. 3 Berühren Sie das Icon, um in den iPod-Modus zu gelangen.
BILDSCHIRMEINSTELLUNGEN 1. Aufrufen des Menüs: ■ Drücken Sie SMART-DIAL Drehknopf auf dem Bedienteil oder drücken Sie die MENUTaste auf der Fernbedienung, um das Hauptmenü aufzurufen. Icon auf dem Bildschirm, um das Menü für die Bildschirmeinstel■ Berühren Sie das lungen aufzurufen. O 2. Auswahl eines Menüpunktes: 1. Drücken Sie eine der []/[] -Tasten, um den Menüpunkt auszuwählen, dessen Wert sie verändern möchten. 2.
DEUTSCH Einstellung Helligkeit Neigungswinkel Bildschirmschoner Kalibrieren des Touchscreens Firmware Version Einstellbereich Funktion 0 bis 20 Drücken Sie eine der []/[]-Tasten auf der Fernbedienung, betätigen Sie den Drehregler (POWER) auf dem Bedienteil oder berühren Sie das entsprechende Icon auf dem Bildschirm, um die Helligkeit des Bildschirms einzustellen.
SETUP 1. Aufrufen des Menüs: 1. Drücken Sie SMART-DIAL Drehknopf auf dem Bedienteil oder drücken Sie die MENUTaste auf der Fernbedienung, um das Hauptmenü aufzurufen. Icon auf dem Bildschirm, um das Setup aufzurufen. 2. Berühren Sie das 3. Berühren Sie den orangen Pfeil, um die nächste Seite des Menüs aufzurufen. N 2. Auswahl eines Menüpunktes: 1. Drücken Sie eine der []/[] -Tasten, um den Menüpunkt auszuwählen, dessen Wert Sie verändern möchten. 2.
DEUTSCH Einstellung Option Funktion Einstellen der Lautstärke von Verkehrsdurchsagen TA Vol USA Radio S-Amerika1 Europa Einstellen der Uhrzeit (HH:MM) Einstellen der Uhrzeit. 12 Stunden 24 Stunden Normal Anzeige der Uhrzeit im 12-Stunden-Modus (AM und PM). Anzeige der Uhrzeit im 24-Stunden-Modus. Das Kamerabild wird normal angezeigt. Umkehren Das Kamerabild wird spiegelverkehrt angezeigt. Auto Die Ausgabe des Videosignals erfolgt automatisch je nach Videomaterial (PAL oder NTSC).
7. UKW/MW-TUNER AUSWAHL DES RADIOMODUS ■ Drücken Sie mehrmals die SRC-Taste auf der Fernbedienung oder auf dem Bedienteil des Geräte, um den Radiomodus als Wiedergabequelle auszuwählen. Icon auf dem Bildschirm, um den Radiomodus als Wieder■ Berühren Sie das gabequelle auszuwählen. BENUTZEROBERFLÄCHE 1 3 4 cm 6 cm cn bm 2 5 bl bt bu cl cp 7 8 9 bn bo bp bq br bs co 01. Aktueller Wiedergabemodus. Berühren Sie das Icon, um das Hauptmenü aufzurufen. 02. Anzeige des eingestellten Frequenzbandes.
DEUTSCH f C D ] \ Z 15. Berühren Sie das Icon, um den automatischen Suchlauf durch Erhöhen der Frequenz zu starten. Icon, um den manuellen Suchlauf zu starten. Mit jeder weiteren 16. Berühren Sie das Berührung wird die Frequenz um einen Schritt verringert. 17. Berühren Sie das Icon, um den manuellen Suchlauf zu starten. Mit jeder weiteren Berührung wird die Frequenz um einen Schritt erhöht. 18. Berühren Sie das Icon, um die AF-Funktion zu de- bzw. aktivieren. 19.
B AUTOMATISCHES SPEICHERN VON SENDERN (AS) ■ Drücken Sie die AS/PS-Taste auf der Fernbedienung oder berühren Sie das Icon auf dem Bildschirm, um den automatischen Suchlauf zu starten und auf den 6 Speicherplätzen des gerade ausgewählten Frequenzbandes zu speichern. ■ Drücken Sie die Taste bzw. berühren Sie das Icon erneut um den automatischen Suchlauf zu beenden.
DEUTSCH 8. DVD-WIEDERGABE AUSWAHL DES DVD-MODUS ■ Drücken Sie mehrmals die SRC-Taste auf der Fernbedienung oder auf dem Bedienteil des Geräte, um den DVD-Modus als Wiedergabequelle auszuwählen. Icon auf dem Bildschirm, um den DVD-Modus als Wieder■ Berühren Sie das gabequelle auszuwählen. BITTE BEACHTEN ■ Wenn Sie das Gerät ordnungsgemäß angeschlossen haben, kann das Bild eine DVD nur dann auf dem Bildschirm wiedergegeben werden, wenn die Handbremse angezogen ist.
BENUTZEROBERFLÄCHE 8 9 1 2 1. 2. 3. 4. 5. 6. Berühren Sie das Berühren Sie das Berühren Sie das Berühren Sie das Berühren Sie das Berühren Sie das zugeben. 7. Berühren Sie das 8. Berühren Sie das 9. Berühren Sie das 3 4 5 6 7 Icon, um die Wiedergabe einer DVD zu starten oder zu pausieren. Icon, um die Wiedergabe einer DVD zu beenden. Icon, um den schnellen Rücklauf zu starten. Icon, um den schnellen Vorlauf zu starten. Icon, um die Wiedergabe einer DVD zu wiederholen.
DEUTSCH ZEITLUPE ■ Drücken Sie die -Taste auf der Fernbedienung, um die DVD bzw. ein Teil der DVD in Zeitlupe wiederzugeben. Durch wiederholtes drücken der Taste können Sie die Geschwindigkeit (1/2, 1/4, 1/6 oder 1/7) der Zeitlupenwiedergabe entsprechend einstellen. ■ Drücken Sie während der Zeitlupe die OK-Taste, um wieder zum normalen Wiedergabemodus zurückzukehren.
AUFRUFEN DES DVD-MENÜS 1. Berühren Sie während der Wiedergabe einer DVD Bereich E und anschließend das Icon auf dem Bildschirm des Gerätes, um das DVD-Menü aufzurufen. 2. Drücken Sie eine der Pfeiltasten auf der Fernbedienung, um die Titelauswahl aus dem Menü auszuwählen. 3. Drücken Sie die TITLE-Taste auf der Fernbedienung, um einen Titel von der DVD auszuwählen. 4.
DEUTSCH Track Search Time Track ---/--- VCD Spielzeit: Wiedergabe wird bei der ausgewählten Spielzeit fortgesetzt. Track: Wiedergabe wird beim ausgewählten Track fortgesetzt. 3. Berühren Sie das rufen. 1 2 3 4 5 6 7 8 9 Icon auf dem Bildschirm, um das numerische Eingabefeld aufzu- 0 4. Geben Sie mit Hilfe der numerischen Tasten auf der Fernbedienung oder des numerischen Eingabefeldes auf dem Bildschirm die entsprechende Spielzeit bzw. das entsprechende Kapitel ein. 5.
AUSWAHL VON VERSCHIEDENEN TONSPUREN (NUR DVD) ■ Einige DVD’s bieten die Möglichkeit, deren Inhalt in verschiedenen Sprachen (Tonspuren) wiederzugeben. Drücken Sie die AUDIO-Taste auf der Fernbedienung oder berühren Sie Bereich E des Bildschirms und anschließend das Icon, um zwischen den verschiedenen Tonspuren zu wählen.
DEUTSCH Wiedergabeinformationen VCD Die folgende OSD-Anzeige erscheint während der Wiedergabe einer VCD auf dem Bildschirm 4 VIDEO CD T:4/16 00:02:05 1 2 3 6 USER ON 08:06 5 1. Anzeige des aktuellen Wiedergabemodus. 2. Der vierte Track einer VCD mit 16 Tracks wird gerade wiedergegeben. 3. Anzeige der Spielzeit des aktuellen Titels. 4. Anzeige der Equalizer Einstellung. 5. Anzeige der Loudness Einstellung. 6. Anzeige der Uhrzeit.
DISC SYMBOLE Symbol Bedeutung Anzahl der Tonspuren, die auf der DVD enthalten sind (maximal 8). Anzahl der Untertitel, die auf der DVD enthalten sind (maximal 32). Anzahl der Kameraperspektiven die auf der DVD enthalten sind (maximal 9). Angabe über die verschiedenen Bildformate, die auf der Disc gespeichert sind. Die Buchstaben “LB” stehen für Letter Box und “PS” für PAN/SCAN. Das abgebildete Symbol bedeutet, dass man das 16:9 Bildformat als Letter Box darstellen kann.
DEUTSCH 9. DVD-SETUP ■ Folgende Menüpunkte stehen Ihnen zur Auswahl: Sprache ➔ Video ➔ Rating AUFRUFEN DES DVD-SETUPS ■ Sie haben mehrere Möglichkeiten das DVD-Setup aufzurufen: 1. Drücken Sie den SMART-DIAL Drehknopf auf dem Bedienteil oder berühren Sie Bereich A auf dem Bildschirm, um das Hauptmenü aufzurufen. Betätigen Sie anschließend den SMART-DIAL Drehknopf oder berühren Sie direkt das M Icon, um das DVD-Setup aufzurufen. 2.
SPRACHWAHL ■ Wenn eine DVD mehr als eine Tonspur oder mehr als einen Untertitel enthält, können Sie während der Wiedergabe zwischen den verschiedenen Optionen wählen. Wenn die von Ihnen ausgewählte Tonspur bzw. der Untertitel nicht auf der DVD enthalten ist, wird die DVD in der voreingestellten Sprache wiedergegeben.
DEUTSCH VIDEOEINSTELLUNGEN Einstellung TV Shape (Aspect Ratio) Verschiedene Kamerapositionen Option 4:3 16:9 An Aus Funktion Keine Funktion Wiedergabe im 16:9 Format Anzeige des Symbols für mehrere vorhandene Kamerapositionen während der Wiedergabe Keine Anzeige des Symbols für mehrere Kamerapositionen während der Wiedergabe Fill Original Erweiterte Bildformateinstekkung H FIT W FIT Ohne Funktion Fit to Scan Pan Scan BITTE BEACHTEN ■ Wenn Sie Discs wiedergeben, die nicht im Widescreen Format aufge
JUGENDSCHUTZKONTROLLE ■ Das Gerät verfügt über eine eingebaute Jugendschutzkontrolle, um zu verhindern, das Kinder und Jugendliche DVD’s mit ungeeigneten Inhalten mit dem Gerät wiedergeben können. Im Auslieferungszustand ist die RATING-Funktion deaktiviert. Nach der Eingabe eines 4-stelligen Codes wird die RATING-Funktion aktiviert und lässt sich auch nur durch die Eingabe des Codes deaktivieren.
DEUTSCH 10. CD/MP3/WMA/JPEG-WIEDERGABE AUSWAHL DES CD/MP3/WMA/JPEG-MODUS ■ Drücken Sie mehrmals die SRC-Taste auf der Fernbedienung oder auf dem Bedienteil des Geräte, um den CD/MP3/WMA/JPEG-Modus als Wiedergabequelle auszuwählen. Icon auf dem Bildschirm, um den CD/MP3/WMA/JPEG-Modus ■ Berühren Sie das als Wiedergabequelle auszuwählen. ■ Die Bedienung der folgenden Funktionen sind während der Wiedergabe einer DVD, CD oder MP3-Disc nahezu identisch.
1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. Anzeige der ausgewählten Programmquelle. Name der gerade wiedergegebenen Disc. Name des gerade wiedergegebenen Tracks. Anzeige der Uhrzeit. Icon, um die Wiedergabe eines Tracks zu starten bzw. zu Berühren Sie das pausieren. Icon, um die Wiedergabe eines Tracks zu stoppen. Berühren Sie das Icon, um die vorherige Seite der Liste mit den sich auf der Berühren Sie das Disc befindlichen Tracks anzuzeigen.
DEUTSCH WIEDERGABE VON MP3/WMA DISCS BENUTZEROBERFLÄCHE 1 2 3 4 bq br bn bo bu bs bp bt 5 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 6 7 8 9 bl bm Anzeige der ausgewählten Programmquelle. Name des gerade wiedergegebenen Ordners. Name des gerade wiedergegebenen Tracks. Anzeige der Uhrzeit. Icon, um die Wiedergabe eines Tracks zu starten bzw. zu Berühren Sie das pausieren. Icon, um die Wiedergabe eines Tracks zu stoppen.
WIEDERGABE VON MP3/WMA DATEIEN ■ Nachdem Sie eine MP3/WMA Disc eingelegt haben, werden die darauf gespeicherten Ordner bzw. Tracks nacheinander wiedergegeben. Während der Wiedergabe können Sie die einzelnen Tracks direkt durch drücken einer der numerischen Tasten auf der Fernbedienung oder durch drücken der entsprechenden Icons auf dem Bildschirm auswählen.
DEUTSCH 11. DAS IPOD INTERFACE AUSWAHL DES IPOD-MODUS ■ Drücken Sie mehrmals die SRC-Taste auf der Fernbedienung oder auf dem Bedienteil des Geräte, um den iPod als Wiedergabequelle auszuwählen. Icon auf dem Bildschirm, um den iPod als Wiedergabequelle ■ Berühren Sie das auszuwählen. BENUTZEROBERFLÄCHE 1 2 3 4 bt bu bn bo bp cn cl bq br cm bs 5 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 6 7 8 9 bl bm Anzeige der ausgewählten Programmquelle. Name des gerade wiedergegebenen Ordners.
S j Icon, um das numerische Tastenfeld auf dem Bildschirm 16. Berühren Sie das aufzurufen. Icon, um das Inhaltsverzeichnis des iPods anzuzeigen. 17. Berühren Sie das 18. Anzeige des gerade wiedergegebenen Tracks und die Gesamtanzahl der sich im Ordner befindlichen Tracks. 19. Anzeige der abgelaufenen Spielzeit des gerade wiedergegebenen Tracks. 20. Anzeige des Loudness-Modus. 21. Anzeige der eingestellten Lautstärke. 22. Anzeige des Equalizer-Modus. 46 ZE-MC172 Manual D+E-CS3.indd 46 06.09.
DEUTSCH 12. FEHLERSUCHE GENERELLE PROBLEME: Problem Ursache Lösung Das Gerät lässt sich nicht einschalten. 1. Die Sicherung des Gerätes ist defekt. 1. Wechseln Sie die defekte Sicherung aus. Die Fernbedienung funktioniert nicht. Keine bzw. zu leise Audiowiedergabe. 2. Die Fahrzeugsicherung ist defekt. 2. Wechseln Sie die defekte Sicherung aus. 3. Falsche Bedienung. 3. Drücken Sie die RESET-Taste, um das Gerät, bzw. alle Einstellungen in den Auslieferungszustand zurückzusetzen. 1.
TUNER: Problem Ursache Lösung Der Radioempfang ist schlecht. 1. Die automatische Antenne ist nicht vollständig ausgefahren. 1. Überprüfen Sie entsprechend die Installation, bzw. die Verkabelung der automatischen Antenne. 2. Die automatische Antenne ist nicht richtig angeschlossen. 2. Überprüfen Sie entsprechend die Installation, bzw. die Verkabelung der automatischen Antenne. 3. Die “REG“ Funktion ist aktiviert. 3. Deaktivieren Sie die “REG“ Funktion.
DEUTSCH EINGABE DES SICHERHEITSCODES: Problem Ursache Lösung Das Gerät lässt sich nicht mehr in Betrieb nehmen und die Eingabe eines Sicherheitscode wird verlangt. 1. Das Gerät wurde länger als 40 Sekunden von der Spannungsquelle getrennt und die Funktion “Eingabe eines Sicherheitscode“ wurde davor aktiviert. 1. Geben Sie den von Ihnen im Vorfeld festgestellten Sicherheitscode ein um das Gerät wieder in Betrieb zu nehmen. Der eingegebene Sicherheitscode wird nicht angenommen. 1.
13. SPEZIFIKATIONEN CEA power ratings Main amplifier Power output: 20 Watts RMS X 4 channels into 4 Ohms @ < 10% THD+N Signal to noise ratio: 70dBA below reference. (Reference: 1 Watt, 4 Ohms) MAX power: 35 X 4 Watts into 4 Ohms, all channels driven Frequency response: 20Hz to 20kHz, -3dB. Aux input used as source reference Reference supply voltage: 14.
DEUTSCH AM tuner section Tuning range: 530kHz – 1710kHz Sensitivity (–20dB): 20dBu Signal to noise ratio @ 1kHz: 50dB Image rejection: 60dB Frequency response: 50Hz – 2kHz, –3dB Monitor section Screen size: 7" (measured diagonally).
CONTENTS Thank you for choosing this ZENEC moniceiver. We hope you will find the introductions in this user manual clear and easy to follow. If you take a few minutes to read it over, you’ll learn how to operate your moniceiver properly. After you have finished reading the instructions, keep this manual in a safe place for future reference. PREPARATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54-55 FEATURES. . . . . . . . . . . . . . . . . .
ENGLISH TUNER OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72-73 TUNER TFT DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72-73 SWITCH TO RADIO TUNER SOURCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 SELECT FM/AM BAND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 AUTO TUNING . . . . . . . .
PREPARATION Please read all the instructions before beginning the installation. We recommend having your ZE-MC172 installed by a skilled dealer or a professional installer.
ENGLISH ■ ■ ■ ■ ■ ■ Electrical tape Crimping tool Volt meter/test light Crimp connections 18 gauge wire for power connections 16 – 18 gauge speaker wire WARNING! 1. Only connect the unit to a 12-volt power supply with proper grounding. 2. Never install this unit where operation and viewing could interfere with safe driving conditions. 3. To reduce the risk of a traffic accident (except when using the rear view video camera) never use the video display function while driving the vehicle.
CONTROLS AND INDICATORS BUTTON OPERATION bq bo bp bn bm 1 2 4 3 5 6 7 9 bl bu cl bs br bm 1 2 4 3 5 6 7 cm bt 8 9 bl 56 ZE-MC172 Manual D+E-CS3.indd 56 06.09.
ENGLISH 1. POWER OFF/VOL ■ Rotary encoder. Press the encoder to turn on the unit, press and hold it to turn off. ■ Rotate it clockwise/anticlockwise to adjust the volume. 2. IR REMOTE CONTROL RECEIVER 3. PREVIOUS 4. MUTE ■ Press the MUTE button to mute the volume and press it again to restore the volume. 5. SRC ■ Press the SCR button once to select playing mode. 6. PLAY/PAUSE ■ Press the PLAY/PAUSE button once for play/pause. 7. NEXT 8. DISC SLOT 9. RESET 10. SMART DIAL ■ Rotary encoder.
19. AS/PS (Auto store/program scan) ■ Press the AS/PS button to auto store strong radio stations in the 12 preset channels of the current band. ■ Press and hold it to start to scan radio station. 20. FM/AM ■ Press the FM/AM button to switch between FM and AM. 21. DISC INDICATOR LIGHT ■ It is white when there is no disc in the unit. It is red when there is a disc in the unit. LCD DISPLAY / INDICATORS 2 345 1 6 7 8 1. Main Display ■ Displays the time, tuning frequency and other text information. 2.
ENGLISH THE KEY AREAS OF TOUCH SCREEN The touch key areas are outlined below, for DVD, VCD, playback mode and so on. Area A Area F Area B Area C Area D Area E Area A: ■ Return to main menu. Area B: ■ DISP key: Displays playing information of a disc. Area C: ■ Select previous chapter (DVD). Area D: ■ Select next chapter (DVD). Area E: ■ Display the on-screen controls, different mode displays or different menu.
Remote Control REMOTE CONTROL Remote Control 2 ,2 1 ,1 ,3 3 ,4 4 6 ,6 7 ,7 8 ,8 bl ,10 bm ,11 bo ,13 bp ,14 bq ,15 bu ,19 cl ,20 co ,23 cp ,24 cs ,27 ct ,28 ,5 5 ,9 9 bn ,12 ,16 br ,17 bs bt ,18 cm ,21 ,22 cn ,25 cq cr ,26 Ref 1. POWER Name # ■ Turns the power on/off. Power Signal Function 1 Turns the power on/ off Op e n/close the TFT m onitor Toggle s on/ off audio output SRC 4 Selects playing mod e 1.2.3.4.5. Directly access chapter/track/pre set station Numeric 5 MUTE 6.7.8.9.
ENGLISH 7. VOL DOWN ■ Decrease volume. 8. INFORMATION ■ Displays playing information. 9. – / – – ■ Press to activate GOTO search for VCD/DVD discs. 10. STOP/BAND ■ Selects FM/AM band on tuner mode. ■ Stop playback of other mode, i.e. disc playback. 11. SELECT ■ Enters the audio menu. 12. ESC ■ To jump back, i.e. to leave a menu. 13. MENU ■ Enters the main menu of system. 14. PICTURE ■ To enter the picture adjustment menu. 15. REPEAT A→B ■ Setup to repeat playback from time frame A to time frame B. 16.
22. PREVIOUS ■ Selects the previous chapter/track for playback. ■ Searches an available radio station by decreasing tuning frequency. 23. FAST REVERSE ■ Fast reverse the disc content. 24. FAST FORWARD ■ Fast forward the disc content. 25. AUDIO ■ Change the audio language for disc playback. 26. ZOOM ■ Zooming IN/OUT on image. 27. ANGLE ■ Plays back disc in different angle for a scene. 28. SUBTITLE ■ Language selection for subtitle. 62 ZE-MC172 Manual D+E-CS3.indd 62 06.09.
ENGLISH USING THE TFT MONITOR OPEN/CLOSE TFT MONITOR ■ Press the [ ] button on the front panel or press the [ open/close the monitor. ] button on the remote control to TFT MONITOR AUTO OPEN ■ If “TFT Auto Open” is “on” when the unit is turned on, the monitor automatically moves to the last viewing position. ■ If “TFT Auto Open” is ”off” when the unit is turned on, press the [ ] button on the front panel or press the [ ] button on the remote control to move the monitor into the desired viewing position.
ADJUSTABLE PARAMETERS ■ While in DVD, iPOD or TUNER mode, the only parameter that can be adjusted is brightness (BRIGHT). ■ To access “PICTURE”, “COLOR”, “CONTRAST”, and “TINT” you must be in AUX or CAMERA mode. PARAMETER ADJUSTMENT PROCEDURE 1. Enter picture quality setting mode: Press the PIC button on the remote control or press and hold the INFO button on the front panel. 2.
ENGLISH THE BASIC OPERATION POWER ON/OFF ■ Press the POWER OFF/VOL button to turn on the unit. The buttons on the front panel of the unit light up and “WELCOME” appears briefly in the LCD panel, followed by the current mode status. If the TFT screen is open, only the current mode status is displayed. ■ Press and hold the POWER OFF/VOL button on the front panel or the POWER button [ ] on the remote control to power off the unit.
1. Accessing the audio control menu Press the POWER/VOL button on the front panel once or press the SEL button on the remote control to display the “AUDIO” menu. 2. Selecting an audio feature for adjustment Press the [] or [] button on the remote control or press the POWER/VOL button on the front panel once to select an audio feature to be adjusted. 3.
ENGLISH Settings Anti-theftcode Default 0000 Options ---- Functions You have to enter the password to turn anti-theft on or off. Anti-theft Off On System will require a password, if main battery power is remove for more than 40 seconds. No password is required, if main battery power is remove. Off SYSTEM RESET ■ To correct a system halt or an unwanted operation, use the tip of a pen to press the RESET button located on the front bottom-right corner of the unit.
SYSTEM MENU SETUP MAIN MENU There are three methods to access the MAIN menu. ■ Press the SMART DIAL button on the front panel. ■ Press the MENU button on the remote control. ■ Touch area A on the touch-screen. 1 2 3 4 5 6 7 1 Touch to access Tuner mode. 2 Touch to access DVD mode. 3 Touch to access iPod mode. 4 Touch to access AV IN mode. 5 Touch to access Camera mode. 6 Touch to access Screen setup. 7 Touch to exit the menu.
ENGLISH SCREEN SETTING Accessing the screen setup menu ■ Press the SMART DIAL on the front panel or press the MENU button on the remote control to access the MAIN menu. ■ Touch the button on the screen to access the screen setup. O Selecting a feature for adjustment ■ Press the [] or [] button on the remote control to select a feature to be adjusted. ■ Rotate SMART DIAL clockwise/anticlockwise to select a feature to be adjusted.
GENERAL SETUP MENU Accessing the general setup menu N button on the screen to access the GENERAL setup. ■ Select the Selecting a feature for adjustment Press the direction buttons on the remote control or touch the option directly on the screen to select the feature to be adjusted. Adjusting a feature 1. Enter the option field for the feature you want to adjust by pressing the OK button on the remote control or by pressing the SMART DIAL button. A submenu appears in a second row with the selected option.
ENGLISH Setting Options Function TA Vol Radio TA Loudness USA Select the appropriate setting based on the country in which you reside. S-Amert Europe Clock (HH:MM) See “Adjusting the clock” to learn how to set the clock. 12Hr Clock displays 12 hour time using AM and PM. 24Hr Clock displays 24 hour time up to 23:59 Clock mode Cam image Normal Reverse Auto TV system NTSC For color signal output in the standard NTSC format. PAL For color signal output in the standard PAL format.
TUNER (FM/AM) OPERATION TUNER TFT DISPLAY 1 3 4 cm 6 cn bm 2 5 7 8 bl bt bu cl 9 cp bn bo bp bq br bs co 01. Current source information, touch this area to return to MAIN MENU. 02. Current radio band indicator. 03. Current preset station playing back indicator. 04. Stereo broadcasting indicator. 05. Radio frequency indicator. 06. Preset radio stations: Touch to recall preset stations or touch and hold to store a station, (total 6 stations a band you can preset). 07.
ENGLISH 18. Alternative frequency (AF) indicator: Touch to activate/deactivate the AF function. 19. Traffic announcement indicator: Touch to activate/deactivate the TA function. Touch to activate/deactivate the REG function. 20. 21. PS indicator. 22. PTY indicator. 23. Touch to activate/deactivate the SCAN function. 24. Touch to choose between STEREO and MONO. Z [ K h SWITCH TO RADIO TUNER SOURCE ■ Press the SRC button on the front panel or on the remote control to switch to the tuner source.
DVD PLAYER OPERATION NOTE: When properly installed, DVD video cannot be displayed on the main TFT screen unless the parking brake is applied. If you attempt to play a DVD while the vehicle is moving, the TFT screen displays caution information with a blue background. Rear video screens, if applicable, will operate normally. OPENING/CLOSING THE TFT VIDEO SCREEN Opening the TFT screen ■ To open the TFT video screen, press the button on the remote control.
ENGLISH USING THE TOUCH-SCREEN CONTROLS 8 9 1 1. 3. 5. 7. 2 Touch to play/pause. Touch to fast reverse. Touch to repeat playback. Touch to switch among LEFT, RIGHT, STEREO. 3 4 5 2. 4. 6. 8. 9. 6 7 Touch to stop playback. Touch to fast forward. Touch to repeat from A to B. Touch to display subtitle. Touch to return to DVD main menu.
Repeat Playback ■ Press the button on the screen or on the remote control to alter repeat mode according to the following: ■ DVD: Repeat Title, Repeat Chapter, Repeat Off ■ VCD (PBC Off): Repeat Single, Repeat Off ■ MP3: Repeat Single, Repeat Folder, Repeat Off NOTE: ■ For VCD play, the repeat function is not available if PBC is on. PBC (playback control) (VCD only) ■ For VCDs with playback functionality, playback control (PBC) provides additional controls for VCD playback.
ENGLISH ■ Press the [] button on the remote control or touch the button of the area E on the screen to fast forward. Keep pressing or touching and releasing the button to increase the rate from “2X” to “4X”, “8X”, and “20X”. ■ Press the [] button on the remote control or touch the button of the area E on the screen to fast reverse. Keep pressing or touching and releasing the button to increase the rate from “2X” to “4X”, “8X”, and “20X”.
GOTO SEARCH ■ During DVD or VCD playback, perform the following steps to use the GOTO feature to access a specific location on a disc: 1. Press the GOTO button on the remote control to enter the “GOTO” mode. 2. Press the [] or [] button on the remote control to select a category. ■ For DVD mode, you can choose time or title/chapter search. ■ For VCD mode, press the GOTO button to choose between track search, disc search and exit.
ENGLISH ZOOMING ■ Press the ZOOM button on the remote control to enlarge and pan through the video image using the following options: “Q1”, “Q2”, “Q3”, and “OFF”. MULTI-LANGUAGE DISCS (DVD ONLY) Changing audio language ■ If you are watching a disc which is recorded in multiple languages, press the AUDIO button on the remote control to choose a language. You can also touch the area E, and then touch the button.
PLAYBACK INFORMATION ■ During DVD and VCD playback, press the INFO button on the remote control or touch the area B to display the playback information on the screen, including the media playing and current playback time. DVD playback information ■ The following information is displayed at the top of the screen during DVD playback: 2 DVD VIDEO 1 1. 2. 3. 4. 5. 6. 7. 8. T:4/16 C:1/20 3 5 00:01:35 4 7 USER 08:06 LEVEL 2 Rear: OFF 6 8 Indicates the current playing source.
ENGLISH GENERAL DISC INFORMATION Symbol 12cm Disc Properties Max Play Time Single side single layer (DVD-5) Single side double layer (DVD-9) Double side single layer (DVD-10) Double side double layer (DVD-18) (MPEG 2 Method) 133 minutes 242 minutes 266 minutes 484 minutes Single side single layer (VCD) (MPEG 1 Method) 74 minutes Single side single layer 74 minutes 81 ZE-MC172 Manual D+E-CS3.indd 81 06.09.
Disc Symbols Symbol Meaning Number of the audio languages which were recorded. The number inside the icon indicates the number of languages on the disc (maximum of 8). Number of subtitle languages available on the disc (maximum of 32). Number of angles provided (maximum of 9). Aspect ratios available. “LB” stands for letter box and “PS” stands for Pan/Scan. In the example on the left, the 16:9 video can be converted to letter box video. Indicates the region code where the disc can be played.
ENGLISH DVD SETUP MENU In “DVD setup” mode, “LANGUAGE”, “VIDEO” and “RATING” (parental lock) are available for setup. This operation can be performed using the rotary encoder, the remote control or the touchscreen. ACCESSING THE DVD SETUP SCREEN You can access DVD setup screen through following methods: ■ Press the SMART DIAL button on the front panel or touch the area A to access the MAIN menu, and then touch the button to access the DVD setup screen.
LANGUAGE MENU If a DVD supports more than 1 subtitle or audio language, all the languages are available for selection during the playback. If the selected language is not supported by the DVD, the default language will be used. During the playback, press the SUBT or AUDIO button on the remote control to change the language directly. This will not affect the DVD menu settings.
ENGLISH VIDEO MENU VIDEO menu features Setting Options Function TV Shape (Aspect Ratio) 4:3 No Function. 16:9 Image is presented in wide view with a 16:9 aspect ratio. On Angle indicator (if applicable) is shown. Off Angle indicator is not shown. Angle Mark Fill Original View Mode H FIT W FIT No function. Fit to Scan Pan Scan Priority Content DVD-VIDEO Play back priority DVD AUDIO content.
RATING (PARENTAL LOCK) MENU The DVD system has a built-in parental lock feature to prevent unauthorized persons from viewing restricted disc content. By default, the rating system is unlocked. Once set up, the parental lock is released only by entering the correct password. Once the password is entered, rating is available for setup. RATING menu features Setting Options Function Password –––– Enter a 4-digit password to activate the “Rating” feature. 1. Kid Safe 2. G 3. PG Rating 4. PG-3 5.
ENGLISH CD/MP3/WMA/JPEG OPERATION Instructions for Insert/Eject, Play/Pause, Stopping Playback, Track Selection, Fast Forward/ Fast Reverse, Scan, and Random Play are the same for DVD, CD and MP3 operation. Please see the DVD player operation section for information about these topics.
D Q R S 11. Touch to fast forward the current track. 12. Touch to activate/deactivate the repeat single mode. Touch to activate/deactivate the random mode. 13. 14. Touch to enter the numeric key pad. 15. Current track and total number of tracks on disc. 16. Elapsed playing time. 17. EQ and Loudness settings. Volume indicator. 18. W Playing CD files After inserting a CD disc, files will play in the sequence of main directory.
ENGLISH JPEG DISCS 1 2 3 1. Stop playback and return to the picture list. 2. Rotate picture clockwise 90°. 3. Rotate picture anticlockwise 90°. 89 ZE-MC172 Manual D+E-CS3.indd 89 06.09.
iPOD OPERATION Accessing iPod mode iPod mode, press the SRC button on the front panel or the SRC ■ To switch to button on the remote control until the iPod symbol appears at the top of the screen. ■ The touch keys for iPod playback are described below: 1 2 3 4 bt bu bn bo bp cl bq br cm bs 5 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 6 7 8 9 bl bm Current source indicator, touch this area to access the MAIN menu. Disc title. Track title. Current time.
ENGLISH 16. 17. 18. 19. 20. 21. 22. S Touch to display a numeric keypad on the screen to access a track directly. j Current track and total number of tracks on iPod. Touch to display the track list. Elapsed playing time. Anzeige des Loudness-Modus. Playback information. Volume indicator. W 91 ZE-MC172 Manual D+E-CS3.indd 91 06.09.
TROUBLESHOOTING GENERAL Problem Cause Corrective action Unit will not power on. 1. Radio fuse blown. 1. Install new fuse with correct rating. 2. Car battery fuse blown. 2. Install new fuse with correct rating. 3. Illegal operation. 3. Press the [RESET] button located in the bottom right corner of the front panel. 1. Battery depleted. 1. Replace battery with new one. Remote control does not function. No/low audio output. Poor sound quality or distortion. 2. Battery installed incorrectly. 2.
ENGLISH TUNER Problem Cause Corrective action Weak station searching. 1. Auto antenna is not fully extended. 1. Connect the auto antenna control cable properly. 2. Auto antenna not properly connected. 2. Connect the auto antenna control cable properly. 3. LOCAL function is activated. 3. Turn LOCAL function off. Problem Cause Corrective action Cannot insert disc. 1. Disc already inside unit. 1. Eject current disc and insert new one. Disc does not play back. 1. Disc is warped or scratched.
ERROR MESSAGES Message displayed Cause Loading 1. Disc is being read. No Disc 1. Disc is dirty. 1. Clean disc with soft cloth. 2. Disc is upside down. 2. Insert disc with label side up. 3. Disc not present in loading compartment. 3. Insert disc. 1. Disc is dirty. 1. Clean disc with soft cloth. 2. Disc is upside down. 2. Insert disc with label side up. Bad Disc Corrective action Unknown Disc 1. Disc format is not compatible with this unit. Region Error 1.
ENGLISH SPECIFICATIONS CEA power ratings Main amplifier Power output: 20 Watts RMS X 4 channels into 4 Ohms @ < 10% THD+N Signal to noise ratio: 70dBA below reference. (Reference: 1 Watt, 4 Ohms) MAX power: 35 X 4 Watts into 4 Ohms, all channels driven Frequency response: 20Hz to 20kHz, -3dB. Aux input used as source reference Reference supply voltage: 14.
AM tuner section Tuning range: 530kHz – 1710kHz Sensitivity (–20dB): 20dBu Signal to noise ratio @ 1kHz: 50dB Image rejection: 60dB Frequency response: 50Hz – 2kHz, –3dB Monitor section Screen size: 7" (measured diagonally).
ENGLISH 97 ZE-MC172 Manual D+E-CS3.indd 97 06.09.
2 YEARS LIMITED WARRANTY Dear customer Thank you for purchasing this ZENEC product. It is advisable to keep the original packing material for any future transporting of the product. Should your ZENEC product require warranty service, please return it to the retailer from whom it was purchased or the distributor in your country. This ZENEC product is warranted against defective materials or workmanship for a period of TWO years from date of purchase at retail.
WARRANTY/GARANTIE ZENEC MODEL: ZE-MC172 Serial number: .............................................................................................................................. Date of purchase: ......................................................................................................................... Your name: ................................................................................................................................... Your address: ...............................
ZE-MC172 Manual D+E-CS3.indd 100 06.09.