MODEL NO: ZE-DVBT1 0 GPS NAVIGATION SYSTEM 1 CH DVB-T TUNER NAVIGATION SOFTWARE MANUAL (German/English) ZE-NC514_UserManualNavigation_Title_DE_EN.indd 1 04.01.
Urhebervermerk Änderungen am Produkt und den hier enthaltenen Informationen vorbehalten. Diese Bedienungsanleitung darf weder ganz noch teilweise ohne ausdrückliche schriftliche Genehmigung von ZENEC vervielfältigt oder auf irgendeine Art und Weise elektronisch oder mechanisch – einschließlich Fotokopien und Aufnahmen – weitergegeben werden. © 2009 - ZENEC Datenquelle © 2006 Tele Atlas N.V.
Danke, dass Sie sich für ZENEC Navigation Software als Ihr Fahrzeug-Navigationssystem entschieden haben, das Sie direkt an Ihr Ziel bringen wird. Lesen Sie zuerst die Kurzanleitung und nehmen Sie ZENEC Navigation Software sofort in Betrieb. Dieses Dokument enthält eine ausführliche Beschreibung der Software.
Inhaltsverzeichnis 1 Warnungen und Sicherheitsinformationen ................................................................... 7 2 Erste Schritte mit ZENEC Navigation Software........................................................... 8 2.1 Schaltflächen und andere Steuerelemente auf dem Bildschirm .............................................. 10 2.1.1 Die Tastaturen verwenden .............................................................................................................11 2.
3.1.3 Das Ziel aus den Favoriten wählen ................................................................................................37 3.1.4 Das Ziel aus den POIs wählen .......................................................................................................37 3.1.5 Das Ziel aus den letzten Zielen wählen..........................................................................................38 3.1.6 Das Ziel durch Eingabe seiner Koordinaten wählen ....................................
4.5.3 Routenplanungsoptionen ................................................................................................................68 4.5.4 Regionale Einstellungen ................................................................................................................70 4.5.5 Menüeinstellungen ......................................................................................................................... 71 4.5.6 TMC-Einstellungen...............................................
1 Warnungen und Sicherheitsinformationen ZENEC Navigation Software ist ein Navigationssystem mit einem eingebauten GPS-Empfänger, das Ihnen dabei hilft, den Weg zu Ihrem Ziel zu finden. ZENEC Navigation Software übermittelt Ihre GPSPosition nicht an Dritte; Sie können daher auch nicht aufgefunden bzw. verfolgt werden. Bitte schauen Sie nur dann auf das Display, wenn es die Verkehrssituation gefahrlos erlaubt.
2 Erste Schritte mit ZENEC Navigation Software ZENEC Navigation Software wurde für den Gebrauch im Auto optimiert. Sie können das Gerät ganz leicht mit Ihren Fingern bedienen, indem Sie die Schaltflächen und die Karte auf dem Display antippen. ZENEC Navigation Software kann Routen für die gesamte installierte Kartenregion planen; Sie müssen nicht zwischen verschiedenen Landkarten wechseln oder eine ungenaue Übersichtskarte verwenden, um zwischen Kartenbereichen oder Ländern zu navigieren.
Aktionen Anleitung Sie sie in die gewünschte Richtung. x Um die Kartenanzeige schnell zu öffnen: Fahren Sie mit Ihrem Finger auf einer beliebigen Programmseite ganz unten von rechts nach links. x Um das Navigationsmenü schnell zu öffnen: Fahren Sie mit Ihrem Finger auf einer beliebigen Programmseite ganz links von oben nach unten. Inbetriebnahme von ZENEC Navigation Software Wenn Sie ZENEC Navigation Software zum ersten Mal starten, müssen Sie Folgendes tun: 1.
2.1 Schaltflächen und andere Steuerelemente auf dem Bildschirm Wenn Sie ZENEC Navigation Software verwenden, tippen Sie normalerweise auf Schaltflächen auf dem Touchscreen. In ZENEC Navigation Software müssen Sie Ihre Auswahl bzw. Änderungen nur bestätigen, wenn die Anwendung neu gestartet oder eine umfangreiche Neukonfiguration durchgeführt werden muss. Eine Bestätigung ist auch erforderlich, bevor Daten oder Einstellungen von Ihnen gelöscht werden.
Typ Beispiel Beschreibung Verwendung Alphabetische und Jede Taste ist eine alphanumerische Tastaturen, Schaltfläche auf dem auf denen Sie Buchstaben und Touchscreen. Zahlen eingeben können. Virtuelle Tastatur 2.1.1 Die Tastaturen verwenden In ZENEC Navigation Software müssen Sie Buchstaben und Zahlen nur eingeben, wenn es unbedingt erforderlich ist.
2.2 Die Karte verwenden Die Kartenanzeige ist die am häufigsten verwendete Programmseite von ZENEC Navigation Software. Sie können sie vom Navigationsmenü aus aufrufen, indem Sie auf tippen. Weitere Informationen zur Kartenanzeige finden Sie auf Seite 44. 2.2.1 Einzelheiten zu einem Kartenpunkt abrufen x x x Führen Sie folgende Aktionen aus, wenn Sie während der Navigation Details zu Ihrem aktuellen Standort abfragen möchten: 1. Sehen Sie sich die Zeile ganz unten auf der Karte an.
2.2.2 Die Karte verändern Positionsanzeiger auf der Karte: x Aktuelle GPS-Position: x Markierter Punkt (Cursor): (Seite 20) (Seite 21) Mit den folgenden Steuerelementen können Sie die Kartenansicht genau an Ihre Bedürfnisse anpassen. Die meisten dieser Elemente werden nur angezeigt, wenn Sie einmal in die Karte tippen, und verschwinden nach einigen Sekunden Inaktivität wieder.
Aktion Nach links und rechts drehen Schaltfläche(n) Beschreibung Sie können den horizontalen Betrachtungswinkel der Karte im 3D-Modus ändern. , Wenn die GPS-Position verfügbar ist, dreht ZENEC Navigation Software die Karte stets so, dass Ihre Fahrtrichtung nach oben angezeigt wird (Ausrichtung in Fahrtrichtung). Mit diesen Schaltflächen können Sie vom Modus „In Fahrtrichtung“ zu einer anderen Ausrichtung wechseln. Wenn die GPS-Position verfügbar ist und Sie die Karte .
Aktion Schaltfläche(n) Kartendrehung) Schaltflächen für die ZoomVoreinstellungen Beschreibung Tippen Sie auf eine der Voreinstellungsschaltflächen, um den Maßstab auf einen fixen, voreingestellten Wert zu setzen. Smart Zoom ist deaktiviert. Diese Schaltflächen sind im 2D-Modus verfügbar. Tippen Sie auf eine der Schaltflächen und halten Sie sie gedrückt, um ihren Wert auf den aktuellen Maßstab zu setzen oder sie auf den ursprünglichen Wert zurückzusetzen.
2.2.4 Statusinformationen und versteckte Steuerelemente auf der Karte Die folgenden Informationen werden in dem runden Feld oben links angezeigt, der Abzweigungsvorschau. Wenn Sie in diesen Bereich tippen, hängt die ausgeführte Aktion von den aktuell angezeigten Informationen ab. Symbol Information Es gibt keine aktive Route , Aktion Tippen Sie in diesen Bereich, um die Suche zu öffnen. Es gibt keine gültige Wenn es eine aktive Tippen Sie in diesen Bereich, GPS-Position.
Symbol Information Details Aktion Verkehrsbeschränkung , Wenn die GPS-Position Wenn Sie in diesen verfügbar ist, es aber keine Bildschirmbereich tippen, zu navigierende Route gibt, geschieht nichts. wird die auf der nächsten Kreuzung geltende Verkehrsbeschränkung angezeigt, sofern es eine gibt.
Die folgenden Informationen sind in den drei Datenfeldern der Kartenanzeige zu sehen. Tippen Sie in diesen Bereich, um die Fahrtinformationen zu öffnen, wo Sie auswählen können, welche Werte in diesen drei Feldern angezeigt werden sollen. Wenn es keine aktive Route gibt, zeigen diese Felder folgende Informationen an: aktuelle Geschwindigkeit, Kompass und aktuelle Uhrzeit.
2.2.5 Den Cursor (den markierten Punkt auf der Karte) verwenden Platzieren Sie zunächst den Cursor mit einer der folgenden Methoden an der gewünschten Stelle in der Karte: x Verwenden Sie das Suchmenü, um einen Ort auszuwählen. Es wird wieder die Karte aufgerufen, auf der der ausgewählte Punkt (der Cursor) in der Mitte angezeigt wird, und das Cursor-Menü mit den verfügbaren Optionen wird geöffnet.
notwendig ist. Ist die nächste Abzweigung etwas weiter entfernt, so werden die Karte und der Betrachtungswinkel verkleinert, sodass Sie den vor Ihnen liegenden Straßenabschnitt gut sehen können. x Während Sie fahren, ohne dass es eine aktive Route in ZENEC Navigation Software gibt: Smart Zoom vergrößert die Karte, wenn Sie langsam fahren, und verkleinert sie, wenn Sie schnell fahren.
2.3.2.2 Zur normalen Navigation zurückkehren Wenn die GPS-Position verfügbar ist und Sie die Karte verschoben haben (das Symbol bewegt sich oder wird gar nicht angezeigt) oder Sie die Karte im 3D-Modus gedreht haben, erscheint die Schaltfläche . Tippen Sie darauf, um die Karte zurück zu Ihrer GPS-Position zu verschieben und wieder in Fahrtrichtung auszurichten (automatische Kartendrehung).
2.3.3 Farbprofile bei Tag und Nacht ZENEC Navigation Software verwendet verschiedene Farbprofile bei Tag und bei Nacht. x Die Farben im Tagmodus ähneln gedruckten Straßenkarten. x In den Farbprofilen für die Nacht sind große Objekte dunkel gefärbt sind, um die relative Bildschirmhelligkeit einzuschränken. ZENEC Navigation Software bietet Ihnen mehrere verschiedene Farbprofile für Tag und Nacht.
2.3.6 Reiseplan Der Reiseplan ist die Liste der nächsten Ereignisse auf Ihrer Route; das heißt, die Navigationsanleitung. Wenn Sie die Karte geöffnet haben, können Sie den Reiseplan auf folgende Arten anzeigen: x x Tippen Sie in den Bereich zwischen der Abzweigungsvorschau und den Fahrtdatenfeldern, wo das Symbol für das übernächste Fahrmanöver (zum Beispiel ) zu sehen ist. Tippen Sie auf die folgenden Schaltflächen: , , .
2.3.7 Meiden Sie haben verschiedene Möglichkeiten, Ihre Route während der Navigation mit der Funktion Meiden umzuleiten. Sie können diese Funktion über das Routenmenü öffnen. Sie haben folgende Optionen: x Tippen Sie auf eine beliebige Entfernungsschaltfläche, wenn Sie ab der nächsten Kreuzung einen Teil der Route umfahren möchten. x : Tippen Sie auf diese Schaltfläche, wenn Sie die obige Funktion schon einmal verwendet haben, um die Einschränkungen aus der Karte zu löschen. 2.3.
, Zusatzinformationen können hinzugefügt werden. Tippen Sie auf die folgenden Schaltflächen: , . 2.3.10 Verkehrsüberwachungskameras Die Standorte von Verkehrsüberwachungskameras stellen eine spezielle POI-Kategorie dar. Im Gegensatz zu den anderen POIs können diese nicht durchsucht werden. Zudem gibt es nur für die Kameras eine spezielle Warnung, wenn Sie sich diesen nähern.
x Displaywarnung: Ein Symbol mit der Geschwindigkeitsbeschränkung erscheint in einer x Warnton: Ein spezieller Warnton wird abgespielt. Ecke der Karte (zum Beispiel: ), 2.3.10.1 Arten von Radargeräten Es gibt verschiedene Arten von Verkehrsüberwachungskameras. Symbol Typ Stationär Mobil Beschreibung Manche Radargeräte sind am Straßenrand angebracht, in eine Richtung blickend, und überwachen den Verkehr in eine oder beide Fahrtrichtungen. Sie messen Ihre aktuelle Geschwindigkeit.
2.3.10.2 Überwachte Richtungen Radargeräte können die Geschwindigkeit in einer Fahrtrichtung, in beiden oder auf einer Kreuzung sogar in mehreren Fahrtrichtungen messen, wenn sie schwenkbar sind. Dasselbe gilt für Rotlichtkameras. ZENEC Navigation Software warnt Sie nur, wenn Sie in die überwachte oder möglicherweise überwachte Richtung fahren.
Wenn an Ihrem Standort öffentliche TMC-Daten ausgestrahlt werden, berücksichtigt ZENEC Navigation Software die empfangenen TMC-Daten automatisch. Sie müssen im Programm keinerlei Einstellungen vornehmen. Der Empfänger sucht unter den FM-Radiosendern automatisch nach TMCDaten und bezieht die decodierten Daten unverzüglich in die Routenplanung mit ein.
3 Mit ZENEC Navigation Software navigieren Sie können Ihre Route in ZENEC Navigation Software auf verschiedene Arten erstellen: x Wenn Sie eine einfache Route erstellen möchten (eine Route mit nur einem Ziel, ohne Zwischenziele), können Sie das Ziel wählen und sofort mit der Navigation beginnen x Sie können eine Route mit mehreren Zielen erstellen x Sie können eine Route auch unabhängig von Ihrer aktuellen GPS-Position bzw. ganz ohne GPS-Empfang erstellen 3.
es als POI oder als Favorit, wenn das Cursor-Menü geöffnet wird. Das Cursor-Menü wird automatisch wieder an derselben Stelle aufgerufen. Jetzt können Sie den Ort als Wegpunkt verwenden. 3.1.2 Eine Adresse oder einen Teil davon eingeben Wenn Ihnen zumindest ein Teil der Adresse bekannt ist, so ist dies der schnellste Weg, das Ziel Ihrer Route festzulegen.
x 4. 4. 6. , um die Ergebnisliste aufzurufen, bevor sie Wählen Sie den Ort aus der Liste. Geben Sie den Straßennamen ein: 1. Tippen Sie auf 2. Beginnen Sie, den Straßennamen über die Tastatur einzutippen. 3. Sie gelangen zur Ergebnisliste: 4. 5. Tippen Sie auf automatisch angezeigt wird. . x Nachdem Sie einige Buchstaben eingegeben haben, werden die auf die Zeichenfolge zutreffenden Namen in einer Liste angezeigt. x Tippen Sie auf automatisch angezeigt wird.
1. Tippen Sie auf die Schaltfläche mit dem Namen des Ortes. Falls Sie das Land/den Bundesstaat geändert haben, tippen Sie bitte auf 2. Beginnen Sie, den Ortsnamen über die Tastatur einzutippen. 3. Sie gelangen zur Liste der Suchergebnisse: 4. 4. x Nachdem Sie einige Buchstaben eingegeben haben, werden die auf die Zeichenfolge zutreffenden Namen in einer Liste angezeigt. x Tippen Sie auf automatisch angezeigt wird. , um die Ergebnisliste aufzurufen, bevor sie Wählen Sie den Ort aus der Liste.
2. ZENEC Navigation Software schlägt Ihnen standardmäßig das Land/den Bundesstaat und den Ort vor, in dem Sie sich gerade befinden. Tippen Sie gegebenenfalls auf die Schaltfläche mit dem Namen des Landes/Bundesstaates und wählen Sie einen anderen Eintrag aus der Liste. 3. So können Sie gegebenenfalls den Ort ändern: , um den Ort aus der Liste der kürzlich x Tippen Sie auf die Schaltfläche verwendeten Ziele zu wählen. x So können Sie einen neuen Ort eingeben: 1.
3.1.2.4 Eine Kreuzung als Ziel wählen Die Vorgehensweise wird vom Navigationsmenü ausgehend erklärt. 1. Tippen Sie auf die folgenden Schaltflächen: 2. ZENEC Navigation Software schlägt Ihnen standardmäßig das Land/den Bundesstaat und den Ort vor, in dem Sie sich gerade befinden. Tippen Sie gegebenenfalls auf die Schaltfläche mit dem Namen des Landes/Bundesstaates und wählen Sie einen anderen Eintrag aus der Liste. 3.
7. Die Karte wird mit dem ausgewählten Punkt in der Mitte aufgerufen. Tippen Sie im CursorMenü auf Navigation beginnen. . Dann wird die Route automatisch berechnet und Sie können mit der 3.1.2.5 Das Ortszentrum (Stadtmitte) als Ziel wählen Das Stadtzentrum ist nicht der geographische Mittelpunkt eines Ortes, sondern ein von den Entwicklern der Karte ausgewählter Punkt. In einer kleinen Stadt oder einem Dorf ist das normalerweise die wichtigste Kreuzung; in größeren Städten eine wichtige Kreuzung.
2. ZENEC Navigation Software schlägt Ihnen standardmäßig das Land/den Bundesstaat und den Ort vor, in dem Sie sich gerade befinden. Tippen Sie gegebenenfalls auf die Schaltfläche mit dem Namen des Landes/Bundesstaates und wählen Sie einen anderen Eintrag aus der Liste. 3. Tippen Sie auf die Schaltfläche mit dem Namen des Ortes und geben Sie die Postleitzahl ein: 1. Beginnen Sie, die PLZ über die Tastatur einzutippen. 2. Sie gelangen zur Ergebnisliste: 3. 4. 6.
x Suchen Sie zuerst nach der Straße mit dem selteneren oder ungewöhnlicheren Namen; Sie müssen weniger Buchstaben eingeben, um sie zu finden. x Wenn eine der Straßen kürzer ist, suchen Sie zuerst nach dieser Straße. Dann können Sie die zweite Straße schneller finden. x Sie können sowohl nach Straßennamen als auch nach der Art der Straße suchen.
x 3. 4. : Es wird nicht rund um einen bestimmten Ort nach dem POI gesucht, sondern anhand der erforderlichen Abweichung, die zur aktiven Route hinzukommt. Das kann nützlich sein, wenn Sie für später einen Zwischenstopp suchen, der nicht weit von der Route entfernt liegt (zum Beispiel eine Tankstelle oder ein Restaurant). Sie können die Suche wie folgt einschränken: x Wählen Sie die POI-Gruppe (z. B. Übernachtung) und danach gegebenenfalls die POIUntergruppe (z. B. Hotel/Motel).
4. Die Karte wird mit dem ausgewählten Punkt in der Mitte aufgerufen. Tippen Sie im CursorMenü auf Navigation beginnen. . Dann wird die Route automatisch berechnet und Sie können mit der 3.1.6 Das Ziel durch Eingabe seiner Koordinaten wählen Die Vorgehensweise wird vom Navigationsmenü ausgehend erklärt. 1. Tippen Sie auf die folgenden Schaltflächen: 2. [optional] Tippen Sie auf ändern. 3. Tippen Sie auf den Wert für die Breite oder die Länge, um die Koordinaten zu ändern. 4.
Sie haben folgende Optionen: Schaltfläche Aktion Der markierte Punkt wird in der Liste nach oben verschoben (wird zu einem Zwischenziel, das früher angesteuert werden soll). Tippen Sie wiederholt auf diese Schaltfläche, um den Punkt zum Ausgangspunkt der Route zu machen. Der markierte Punkt wird in der Liste nach unten verschoben (wird zu einem Zwischenziel, das später angesteuert werden soll). Tippen Sie wiederholt auf diese Schaltfläche, um den Punkt zum endgültigen Ziel der Route zu machen.
3.4 Die Route bearbeiten Tippen Sie auf die folgenden Schaltflächen: , , . Die Liste der Wegpunkte erscheint mit dem Ausgangspunkt ganz oben in der Liste und dem endgültigen Ziel am Ende. Wenn es mehrere Zwischenziele gibt, müssen Sie eventuell umblättern. Tippen Sie auf einen der Wegpunkte in der Liste. Sie haben folgende Optionen: Schaltfläche Aktion Der markierte Punkt wird in der Liste nach oben verschoben (wird zu einem Zwischenziel, das früher angesteuert werden soll).
3.6 Die aktive Route anhalten Sie müssen eine aktive Route nicht anhalten: Sobald Sie wieder losfahren, gibt ZENEC Navigation Software die Sprachanweisungen für Ihren aktuellen Standort wieder aus. 3.7 Das nächste Zwischenziel aus der Route löschen Am einfachsten können Sie den nächsten Wegpunkt (das nächste Zwischenziel) löschen, indem Sie durch Antippen der Abzweigungsvorschau ( öffnen und dann auf ) in der Kartenanzeige die Routeninformationen tippen. Sie haben noch eine Option.
3.9 Eine Route speichern Die Vorgehensweise wird von der Kartenanzeige ausgehend erklärt. 1. Tippen Sie auf die folgenden Schaltflächen: 2. Geben Sie einen Namen für die neue gespeicherte Route ein und tippen Sie dann auf , , . . Wenn Sie eine Route speichern, speichert ZENEC Navigation Software nicht nur die Wegpunkte, sondern den gesamten Reiseplan. x Die gespeicherte Route könnte von TMC-Daten beeinflusst worden sein.
4 Referenzteil Auf den nächsten Seiten finden Sie eine Beschreibung der verschiedenen Menüseiten von ZENEC Navigation Software. Das Navigationsmenü: ZENEC Navigation Software wird im Navigationsmenü geöffnet. Von dort können Sie auf die folgenden Programmseiten zugreifen: Anzeige Schaltfläche Beschreibung Karte Die Kartenanzeige.
Symbol Name Aktion Abzweigungsvorschau, also Zeigt die Routeninformationen an das nächste Ereignis auf Ihrer Route Übernächstes Ereignis auf Öffnet den Reiseplan der Route Fahrtdaten Qualität der GPS-Position Zeigt die Fahrtinformationen an Öffnet das Menü „Schnellzugriff“ Obere Zeile Nächste Straße n.v. Untere Zeile Aktuelle Straße und Hausnummern links und rechts n.v.
Symbol , Name Aktion x Schaltflächen für die ZoomVoreinstellungen (nur in der 2D-Karte) x Schaltflächen für die Kipp- und Zoom-Voreinstellungen (nur in der 3D-Karte) x Schaltfläche „Zur GPS-Position zurückkehren“ x Smart-Zoom-Schaltfläche Nach links und rechts drehen Dreht die 3D-Karte nach links oder rechts Nach oben und unten kippen Kippt die 3D-Karte , Vergrößern und verkleinern Ändert den Kartenmaßstab Zur GPS-Position zurückkehren (erscheint, wenn die GPS-Position verfügbar ist und Sie di
Symbol Name Aktion Tippen Sie auf eine der Schaltflächen und halten Sie sie gedrückt, um ihren Wert auf den aktuellen Neigungswinkel und Maßstab zu setzen oder sie auf den ursprünglichen Wert zurückzusetzen. Aktuelle GPS-Position (auf n.v. der nächstgelegenen Straße) Cursor (markierter Punkt auf n.v. der Karte) Spurangaben n.v. Schilderdaten Orange Linie n.v. Aktive Route n.v. Kartenmaßstab (nur in der n.v. 2D-Karte) 4.1.1 Symbole auf der Karte Auf der Karte gibt es verschiedene Statussymbole.
Symbol Beschreibung Eine GPS-Navigation ist nicht möglich. Es werden nur Signale von wenigen Satelliten empfangen. Es sind Positionsdaten verfügbar, aber die Seehöhe kann nicht berechnet werden. Eine GPS-Navigation ist möglich, Positionierungsfehler auftreten. aber es kann ein deutlicher Es sind Höhenangaben verfügbar; die Position ist eine 3D-Position. Die GPS-Navigation ist möglich. 4.1.1.2 Statusanzeigezeile Das ist eine Kombi-Statusanzeige.
Symbol Beschreibung Leicht rechts abbiegen. , Scharf links abbiegen. , Links halten. , Auf der Kreuzung geradeaus weiterfahren. , In den Kreisverkehr einfahren. Die Nummer der Ausfahrt wird im Kreis angezeigt, aber nur für die nächste Abzweigung. , Auf die Autobahn auffahren. , Die Autobahn verlassen. , Auf die Fähre auffahren. , Von der Fähre abfahren. , Das nächste Zwischenziel naht. , Ihr Ziel naht.
4.1.2.2 Arten von 3D-Objekten Tippen Sie auf die folgenden Schaltflächen, um die 3D-Darstellung auf der Karte zu aktivieren bzw. zu deaktivieren: , , , . ZENEC Navigation Software unterstützt folgende Arten von 3D-Objekten: Typ Beschreibung 3DOrientierungspunkte Orientierungspunkte sind künstlerische Darstellungen von auffallenden oder bekannten Objekten in 3D. 3D-Orientierungspunkte gibt es nur in bestimmten Städten und Ländern.
Symbol Name Beschreibung verwendet werden kann. Wenn die automatische Neuberechnung nach einer Routenabweichung aus einem der oben angeführten Gründe deaktiviert ist, führen Sie -Symbols in der durch Antippen des Abzweigungsvorschau nicht nur eine Routenneuberechnung von der aktuellen GPSPosition aus durch, sondern aktivieren auch wieder die Funktion „Neu planen nach Routenabweichung“. Zwischenziel Ein Zwischenziel ist ein Zwischenstopp auf der Route.
Damit zusätzlich zum Cursor-Menü auch ein Teil der Karte zu sehen ist, werden zunächst nur einige wenige Schaltflächen angezeigt. Tippen Sie auf Schaltfläche , um alle Optionen einzusehen. Beschreibung Schließt das Cursor-Menü und bringt Sie zur vorigen Seite zurück. Verkleinert die Karte. Vergrößert die Karte. Wenn das Cursor-Menü offen ist, können Sie die Karte trotzdem verschieben, vergrößern und verkleinern.
Schaltfläche Beschreibung beibehalten werden kann. Wenn sich der Cursor am oder nahe beim gewählten Ausgangspunkt befindet, ersetzt diese Schaltfläche die vorige Schaltfläche und löscht den Ausgangspunkt aus der Route. Die aktuelle GPS-Position wird wieder als Ausgangspunkt verwendet und die automatische Neuberechnung nach einer Routenabweichung ist wieder aktiviert. Der Cursor wird als Benutzer-POI gespeichert. Wählen Sie die POIGruppe und geben Sie dem POI einen Namen.
Im oberen Bildschirmbereich sehen Sie Informationen über die aktuelle Route. Die Felder auf dieser Seite werden ständig aktualisiert, solange sie geöffnet ist. Wenn Sie die Seite aufrufen, enthalten alle Felder Informationen darüber, wie Sie Ihr endgültiges Ziel erreichen. Tippen Sie auf ein beliebiges Feld, um Daten zu den Zwischenzielen anzuzeigen, angefangen vom ersten Zwischenziel bis wieder zum endgültigen Routenziel.
Name Beschreibung Erscheint nur, wenn es mindestens ein Zwischenziel gibt. Funktion Löscht das nächste Zwischenziel aus der Route. Erscheint nur, wenn es auf Ihrer Route keine Löscht die aktive Route. Zwischenziele gibt. 4.1.6 Fahrtinformationsanzeige In der Fahrtinformationsanzeige sehen Sie sowohl Routen- als auch Fahrtdaten, die Sie während Ihrer Fahrt eventuell benötigen. Sie kann durch Antippen des Fahrtdatenfeldes ( Kartenanzeige aus geöffnet werden.
Name Verbleibende Zeit Ankunftszeit GPS-Zeit Beschreibung Funktion Zeigt anhand der für die verbleibenden Abschnitte der Route verfügbaren Daten an, wie lange Sie noch bis zum endgültigen Ziel Ihrer Route brauchen werden. Bei dieser Berechnung können Staus oder andere mögliche Verzögerungen nicht berücksichtigt werden. Zeigt anhand der für die verbleibenden Abschnitte der Route verfügbaren Daten Ihre voraussichtliche Ankunftszeit am endgültigen Ziel der Route an.
-Symbol zu finden. Dieses Symbol gibt an, ob Neben den meisten Feldern auf dieser Seite ist ein das dazugehörige Feld auf der Karte unter den Fahrtdaten angezeigt wird. Darüber hinaus zeigt es die Position der Daten wie folgt an: Symbol Beschreibung Dieser Wert wird nicht auf der Karte angezeigt. Dieser Wert erscheint in der Kartenanzeige unter den Fahrtdaten. Es handelt sich dabei um den oberen Wert. Dieser Wert erscheint in der Kartenanzeige unter den Fahrtdaten.
4.1.7 Schnellzugriff Im Menü „Schnellzugriff“ finden Sie eine Reihe von Steuerelementen, die während der Navigation oft verwendet werden. Sie kann über die Schaltfläche geöffnet werden. direkt von der Kartenanzeige aus Wenn Sie im Menü „Schnellzugriff“ auf einen beliebigen Schalter tippen, kehren Sie unverzüglich zur Kartenanzeige zurück. Schalter sind aktiviert, wenn die dazugehörigen Lämpchen leuchten.
4.1.8 GPS-Datenanzeige Tippen Sie auf die folgenden Schaltflächen: und dann Datenanzeige zu öffnen und den Status des GPS-Empfangs abzufragen. Symbol Farbe Grün Name Anzeige für die Qualität der GPSPosition Gelb Grau Rot , um die GPS- Beschreibung ZENEC Navigation Software ist mit dem GPS-Empfänger verbunden und GPSPositionsdaten sind in 3D verfügbar: ZENEC Navigation Software kann sowohl Ihre horizontale als auch Ihre vertikale GPS-Position berechnen.
Symbol Farbe Name Beschreibung empfängt sowohl von den grünen als auch den gelben Satelliten Daten. Von den gelben Satelliten werden die Signale nur empfangen, während hingegen die grünen dem GPS-Empfänger zur Ortsbestimmung dienen. Koordinaten n.v. Statusbalken für die Satelliten n.v. Ihre aktuelle GPS-Position im WGS84Format. Dunkle Balken stehen für die gelben und helle für die grünen Satelliten. Je mehr (grüne) Satelliten mit ihrem GPS verbunden sind, desto besser wird Ihre Position berechnet.
4.3 Routenmenü Hier können Sie Ihre Routen speichern, laden und bearbeiten. Tippen Sie auf die folgenden Schaltflächen: , Schaltfläche . Beschreibung Öffnet eine Seite mit nützlichen Routendaten. Referenz Seite 53 Öffnet eine Seite mit verschiedenen Möglichkeiten, Ihre Route Seite 24 während der Navigation rasch umzuleiten. Sie können die Navigationsanweisungen durchsehen, denen Seite 23 ZENEC Navigation Software während der Fahrt folgt.
4.4 Menü „Verwalten“ Sie können die von ZENEC Navigation Software gespeicherten Inhalte verwalten. Tippen Sie auf die folgenden Schaltflächen: , . Schaltfläche Beschreibung Referenz Gespeicherte Routen umbenennen oder löschen Seite 62 Einträge aus den letzten Zielen löschen Seite 63 Favoriten umbenennen oder löschen Seite 64 Seite 63 POIs erstellen, aktualisieren oder löschen POI-Gruppen erstellen, aktualisieren oder löschen POI-Anzeigeeinstellungen ändern 4.4.
4.4.2 Letzte Ziele verwalten Sie können die Liste der zuletzt verwendeten Orte verwalten. Tippen Sie auf die folgenden Schaltflächen: , , . Schaltfläche Beschreibung Löscht den markierten Eintrag aus den letzten Zielen. Löscht alle letzten Ziele. Wechselt zur nächsten bzw. Listeneinträge anzuzeigen. , vorigen Seite, um zusätzliche 4.4.3 POIs verwalten Sie können Ihre POIs verwalten und die POI-Anzeige sowohl für Ihre eigenen POIs als auch für die im Produkt bereits integrierten festlegen.
Wenn eine POI-Gruppe zum Bearbeiten geöffnet ist: Schaltfläche Beschreibung Die Elemente in der POI-Gruppe werden nicht auf der Karte angezeigt. , ... Die Entfernungsschaltflächen legen den Maßstab fest, ab dem die Elemente in der POI-Gruppe auf der Karte angezeigt werden. , Die Anzeigeeinstellungen der POI-Gruppe werden auch für die Untergruppen der bearbeiteten POI-Gruppe übernommen.
4.4.5 Benutzerdaten verwalten Sie können die von Ihnen gespeicherten Daten (Pins, POIs, Favoriten und letzte Ziele) sowie die von Ihnen im Programm vorgenommenen Einstellungen verwalten. Tippen Sie auf die folgenden Schaltflächen: , Schaltfläche , . Beschreibung Pins löschen im Orte auf der Karte können über die Schaltfläche Cursor-Menü mit einem Pin markiert werden. Tippen Sie auf diese Schaltfläche, um alle Pins aus der Karte zu löschen.
Schaltfläche Beschreibung Referenz Diese Einstellungen ermöglichen es Ihnen, das Programm an Seite 70 Ihre Sprache und an die in Ihrem Land verwendeten Maßeinheiten und Datums- und Zeitformate anzupassen. Hier können Sie auch Ihre aktuelle Uhrzeit einstellen und die gewünschte Stimme der Sprachanweisungen wählen. Sie können das Aussehen und die Eigenschaften der Seite 71 Menüseiten ändern. Sie können die Verbindung zum TMC-Empfänger einrichten.
Schaltfläche Beschreibung Sie fest, ob zwischen den Farbprofilen für Tag und Nacht automatisch oder manuell umgeschaltet werden soll. Höhenangaben in der 2DKarte 3D-Daten können auch in 2D-Karten angezeigt werden. Diese Karten, die eine Sicht von oben darstellen, zeigen Erhöhungen durch Farben und Schattierungen an. Straßennamen anzeigen Während der Navigation können die auf der Karte angezeigten Straßennamen und POI-Symbole stören.
Schaltfläche Beschreibung Übersichtsmodus Verfügung: stehen Ihnen folgende Steuerelemente zur x Entfernung der Abzweigung für Übersichtsmodus: Die Karte wechselt in den Übersichtsmodus, wenn das nächste Ereignis auf der Route mindestens in der hier festgelegten Entfernung liegt. x Standardmaßstab: Der Übersichtsmodus wird in diesem Maßstab aufgerufen.
Schaltfläche Beschreibung Route nach einer Routenabweichung neu berechnet wird. Bei der Routenplanung verwendete Straßenarten: Typ Autobahnen Unbefestigte Straßen Mautstraßen Beschreibung Vielleicht müssen Sie Autobahnen meiden, wenn Sie ein langsames Auto fahren oder ein anderes Fahrzeug abschleppen.
Option Beschreibung ZENEC Navigation Software beispielsweise dazu, eine Autobahn anstatt einer Reihe von kleineren Straßen zu wählen. 4.5.4 Regionale Einstellungen Diese Einstellungen ermöglichen es Ihnen, das Programm an Ihre Sprache und an die in Ihrem Land verwendeten Maßeinheiten und Datums- und Zeitformate anzupassen. Hier können Sie auch Ihre aktuelle Uhrzeit einstellen und die gewünschte Stimme der Sprachanweisungen wählen. Tippen Sie auf die folgenden Schaltflächen: , Schaltfläche , .
Schaltfläche GPS-Zeit und Gerätezeit abgleichen Beschreibung gewünschte Uhrzeit einstellen. Die aktuelle Zeit des GPS-Empfängers und die Geräteuhr werden angezeigt. Bitte beachten Sie, dass die GPS-Uhr nur verfügbar ist, wenn das GPS Empfang hat. So können Sie überprüfen, ob eine Korrektur notwendig ist. 4.5.5 Menüeinstellungen Sie können das Aussehen und die Eigenschaften der Menüseiten ändern. Tippen Sie auf die folgenden Schaltflächen: , , Schaltfläche Hintergrund .
Wenn bereits ein TMC-Empfänger angeschlossen ist, sieht die Seite anders aus: Schaltfläche Automatischen Tuner verwenden Beschreibung Wenn der automatische Tuner aktiviert ist, durchsucht der Empfänger von ZENEC Navigation Software das FM-CCIR-Frequenzband nach einem TMC-Signal. Der erste gefundene Sender, der TMC-Daten ausstrahlt, wird automatisch verwendet. Wenn kein TMC-Signal verfügbar ist, sucht der Empfänger immer weiter. Schalten Sie den automatischen Tuner aus, um den Sender manuell zu wählen.
5 Glossar 2D-/3D-GPS-Empfang Der GPS-Empfänger nutzt Satellitensignale, um seinen (Ihren) Standort zu bestimmen. Um eine dreidimensionale Position zu ermitteln (inklusive Höhenangabe), sind mindestens vier Signale erforderlich. Da die Satelliten ständig in Bewegung sind und die Signale von anderen Objekten behindert werden können, empfängt Ihr GPS-Gerät eventuell nicht vier Signale.
Übersichtsmodus Sie können einstellen, dass ZENEC Navigation Software automatisch in den Übersichtsmodus wechselt, wenn das nächste Ereignis auf der Route weiter entfernt liegt. Im Übersichtsmodus wird die Karte in 2D angezeigt, allerdings auf einen voreingestellten Maßstab verkleinert. Wenn Sie sich dem nächsten Ereignis auf der Route nähern, kehrt die zuvor verwendete 2D- oder 3D-Kartenansicht automatisch zurück. Route Eine Reihe von Zielen, die nacheinander angefahren werden sollen.
6 Endbenutzer-Lizenzvertrag 1. Die Vertragsparteien 1.1. Dieser Vertrag wurde von und zwischen NNG Global Services LLC. (eingetragener Sitz: 23 Bérc utca, H-1016 Budapest, Ungarn; Handelsregisternummer: 01-09- 913383) als dem Lizenzgeber (nachfolgend: Lizenzgeber) und Ihnen als dem Nutzer (nachfolgend: Nutzer; der Nutzer und der Lizenzgeber werden gemeinsam die Parteien genannt) betreffend der Nutzung des vertragsgegenständlichen Softwareproduktes abgeschlossen. 2. Abschluss des Vertrages 2.1.
5.4. Durch Abschluss dieses Vertrages behält der Lizenzgeber sämtliche Rechte am Softwareprodukt, mit Ausnahme jener Rechte, die dem Nutzer durch ausdrückliche gesetzliche Regelungen oder durch Bestimmungen dieses Vertrages zugestanden werden. 6. Nutzerrechte 6.1. Der Nutzer ist berechtigt, das Softwareprodukt auf einem Gerät (Desktop-Computer, HandheldComputer, tragbarer Computer, Navigationsgerät) zu installieren, es auszuführen und ein Exemplar des Softwareproduktes bzw.
8.4. Der Lizenzgeber haftet nicht für Schäden aufgrund der Untauglichkeit des Softwareproduktes für einen bestimmten Zweck oder der fehlerhaften oder fehlenden Zusammenarbeit desselben mit anderen Systemen, Geräten oder Produkten (z. B. Software oder Hardware). 8.5. Der Lizenzgeber weist den Nutzer hiermit ausdrücklich darauf hin, dass die Einhaltung der Verkehrsvorschriften und -regeln (z. B.
Zentralbezirksgerichts Pest (Pesti Központi Kerületi Bíróság) oder des Hauptstädtischen Gerichts (FĘvárosi Bíróság) von Budapest. 78 78 ZE-NA2000N_UserManual_DE.indd 78 22.04.
ZE-NA2000N_UserManual_DE.indd 79 22.04.
Copyright note The product and the information contained herein is subject to change without prior notification. This manual may not, in whole or in part, be reproduced or transmitted in any form either electronically or mechanically, including photocopying and recording, without the express written consent of ZENEC. © 2009 - ZENEC Data Source © 2006 Tele Atlas N.V.
Thank you for choosing ZENEC Navigation Software as your door-to-door in-car navigator. Read the Quick Start Guide first and start using ZENEC Navigation Software right away. This document is the detailed description of the software. You can easily discover ZENEC Navigation Software while you are using it; however, we still recommend that you read this manual to understand the screens and the features of ZENEC Navigation Software. 3 ZE-NA2000_UserManual_UK.indd 3 23.04.
Table of contents 1 Warnings and Safety information .................................................................................. 7 2 Getting started with ZENEC Navigation Software....................................................... 8 2.1 Buttons and other controls on the screen ............................................................................... 10 2.1.1 Using keyboards....................................................................................................................
3.1.3 Selecting the destination from your Favourites..............................................................................34 3.1.4 Selecting the destination from the POIs .........................................................................................35 3.1.5 Selecting the destination from the History .....................................................................................36 3.1.6 Selecting the destination by entering its coordinates .........................................
4.5.3 Route Planning options ..................................................................................................................62 4.5.4 Regional settings ............................................................................................................................64 4.5.5 Menu settings .................................................................................................................................65 4.5.6 TMC settings.........................................
1 Warnings and Safety information ZENEC Navigation Software is a navigation system that helps you find your way to your destination with its built-in GPS receiver. ZENEC Navigation Software does not transmit your GPS position; others cannot track you. It is important that you look at the display only when it is safe to do so. If you are the driver of the vehicle, we recommend that you operate ZENEC Navigation Software before you start your journey.
2 Getting started with ZENEC Navigation Software ZENEC Navigation Software is optimised for in-car use. You can use it easily by tapping the screen buttons and the map with your fingertips. ZENEC Navigation Software can plan routes throughout the whole installed map set; you do not need to change maps or switch to a poorly detailed general map to navigate between map segments or countries.
Tasks Instructions x Shortcut to open the Map screen: slide your finger from the bottom right corner to the bottom left corner on any screen. x Shortcut to open the Navigation menu: slide your finger from the top left corner to the bottom left corner on any screen. Start using ZENEC Navigation Software When ZENEC Navigation Software is started the first time, you need to do the following: 1. Select the written language of the application interface. Later you can change it in Settings (page 64). 2.
2.1 Buttons and other controls on the screen When you are using ZENEC Navigation Software, you usually tap buttons on the touch screen. You only need to confirm selections or changes in ZENEC Navigation Software if the application needs to restart, it needs to perform a major reconfiguration, or you are about to lose some of your data or settings. Otherwise, ZENEC Navigation Software saves your selections and applies the new settings without confirmation as soon as you use the controls.
2.1.1 Using keyboards You only need to enter letters or numbers in ZENEC Navigation Software when you cannot avoid it. You can type with your fingertips on the full-screen keyboards and you can switch between various keyboard layouts, for example ABC, QWERTY, or numerical. Task Details Switching to another keyboard layout, for example from an English , and select from the list of available Tap QWERTY keyboard to a Greek keyboard types.
2.2.1 Checking the details of a map location x x x If you are interested in the details of your current position during navigation: 1. Check the bottom line of the map. It shows the current street and house number information. 2. For further details, tap 3. Tap displayed. to open the Position menu. . The address, the coordinate and the list of nearby POIs will be You can check the details of any other location by selecting it on the map: 1. Tap the map anywhere to open the map control buttons.
Action Button(s) Opening/closing map control buttons Zooming in and out Description Tap this button to show or hide the following map control buttons: x Zoom in/out x Rotate left/right (3D map only) x Tilt up/down (3D map only) x Zoom preset buttons (2D map only) x Tilt and zoom preset buttons (3D map only) x Return to GPS position button x Smart Zoom button Changes how much of the map is displayed on the screen.
Action Button(s) Description the next junction. x If the next turn is at a distance, ZENEC Navigation Software zooms out and lowers the view angle to show you the road in front of you. Tap this button once to enable Smart Zoom. Tap&hold the button to set the zoom limits of Smart Zoom. Returning to normal navigation (back to the GPS position with automatic map rotation) Zoom preset buttons Tap this button to move the map back to the current GPS position.
2.2.4 Status information and hidden controls on the map The following information appears in the rounded field in the top left corner, the Turn Preview field. When tapping this area, the result depends on the information currently shown. Icon Information There is no active route , Details If there is no route to be navigated, this icon appears in the Turn Preview field. There is no valid GPS If an active route exists, and Tap this area to open the Route Information screen. position.
Icon Information Details Action Stops the running simulation This icon appears during Tap this area to stop the simulation. Route Simulation. Route recalculation progress During route recalculation, Nothing happens if you tap this area of the screen. this field shows the recalculation progress between 0% and 100%. Indicator strip - sounds muted/enabled Nothing happens if you tap this area of the screen.
Icon Type Distance information More information x Current GPS time x Time remaining to reach the destination x Time remaining to reach the next via point x Estimated arrival time at the destination x Estimated arrival time at the next via point There are distance type values that can be shown: x Distance remaining to reach the destination x Distance remaining to reach the next via point x Current altitude The next area is the GPS position quality indicator field.
Button Action Saves the Cursor as a Road Safety Camera location Marks the map with a Pin at the Cursor Opens a screen with the name, address and coordinate information of the Cursor, and the list of POIs near it 2.3 ZENEC Navigation Software concepts 2.3.
2.3.2 Position markers 2.3.2.1 Current GPS position and Lock-on-Road When your GPS position is available, ZENEC Navigation Software marks your current position with the icon on the map. The icon is aligned to the nearest road to suppress GPS position errors. The direction of the icon is one of the directions of the route. To use the current GPS position, tap position as one of the following: x a Favourite x a POI x a map marker Pin . The Position menu appears and you can save the GPS 2.3.2.
x a Favourite x a POI x a map marker Pin 2.3.2.4 Original position in the Cursor menu When the Cursor menu is open, a special icon ( opened with. ) shows the Cursor position the menu was You can move and zoom the map, and you can set the Cursor to a different place. The usual Cursor ) appears, and the buttons of the Cursor menu initiate actions for this new location. ( To return to the original Cursor position, tap Cursor menu was opened, and the .
x x Economical x Easy Road types x Unpaved Roads x Permit Needed x Motorways x Toll Roads x Charge Roads x Ferries x Cross-border Planning ZENEC Navigation Software automatically recalculates the route if you deviate from the proposed itinerary. If your hardware supports TMC: Depending on the type of the TMC event, ZENEC Navigation Software also recalculates the route if a TMC event concerns a part of the recommended route.
Button Description Moves between pages for additional list items. , When the map is open with a manoeuvre in the middle: Button Description Zooms in the map. Zooms out the map. , Moves the map to show the previous or next manoeuvre. Opens a screen where you can avoid a part of the route starting from the selected manoeuvre. 2.3.7 Avoid You have quick detour possibilities during navigation with the Avoid feature. It can be opened Route menu.
POIs are grouped into several levels of categories and subcategories. The icon of a POI that comes with the map shows the symbol of the POI category. If you save your own POI, you can select an icon for it independently of the POI category you have put it in. Saving POIs To save a POI, place the Cursor ( , ) at the desired location, then tap the following buttons: , .
Camera warning The warning for Road Safety Cameras can be turned on in Warning Settings. Tap the following buttons: , , , . When you approach a Road Safety Camera with the warning enabled, the following happens: x Visible Warning: The type and distance of the camera is displayed in the secondary Turn Preview field (for example ). x Audible Warning: If there is no speed limit specified for the camera, or your speed is under the specified speed limit, single beeps warn you about the camera.
Icon Type Description tap the speed camera symbol displayed on the screen to stop the warning. Tap again to display the second route event with the possibility to open the Itinerary. Red light These cameras check if you obey traffic lights. The warning is similar to mobile speed cameras: as there is no speed limit given, only the proximity is announced. 2.3.10.
TMC is enabled by default in ZENEC Navigation Software. Note! TMC is not a global service. It may not be available in your country or region. Ask your local dealer for coverage details. Your ZENEC In-Car Navigation Device may contain the TMC receiver device that is needed to receive TMC data. Ask your local dealer. If public TMC data is broadcast at your location, ZENEC Navigation Software automatically takes into account the TMC data received. You do not need to set anything in the program.
3 Navigating with ZENEC Navigation Software You can set up your route in ZENEC Navigation Software in several ways: x if you need a simple route (a route with only one destination, without any intermediate via points), you can select the destination and start navigating to it right away x you can plan a multi-point route x you can also plan a route independently of your current GPS position or even without GPS reception 3.
3.1.2 Entering an address or part of an address If you know at least a part of the address, it is the quickest way to select the destination of the route. Using the same screen, you can find an address by entering: x the exact address, including house number x the centre of a settlement x an intersection x the midpoint of a street x any of the above, starting the search with the postal code (page 33) 3.1.2.
3. 4. 5. 6. Get to the list of results: x After entering a couple of characters, the names that match the string appear in a list. x Tap to open the list of results before it appears automatically. Select the street from the list. Enter the house number: 1. Tap 2. Enter the house number on the keyboard. 3. Tap . to finish entering the address. The map appears with the selected point in the middle. Tap from the Cursor menu.
1. 2. Start entering the street name on the keyboard. 3. Get to the list of results: 4. 5. . Tap x After entering a couple of characters, the names that match the string appear in a list. x Tap to open the list of results before it appears automatically. Select the street from the list. Enter the house number: 1. Tap 2. Enter the house number on the keyboard. 3. Tap . to finish entering the address. 6. A list appears with the matching addresses. Tap the desired one. 7.
x 4. 4. to open the list of results before it appears Select the settlement from the list. Enter the street name: 1. Tap 2. Start entering the street name on the keyboard. 3. Get to the list of results: 4. 5. Tap automatically. . x After entering a couple of characters, the names that match the string appear in a list. x Tap to open the list of results before it appears automatically. . Instead of selecting one of the streets, tap Enter the house number: 1. Tap 2.
3. 4. 4. x After entering a couple of characters, the names that match the string appear in a list. x Tap automatically. to open the list of results before it appears Select the settlement from the list. Enter the street name: 1. Tap 2. Start entering the street name on the keyboard. 3. Get to the list of results: 4. 5. Get to the list of search results: . x After entering a couple of characters, the names that match the string appear in a list.
1. Tap the button with the name of the settlement, or if you have changed the . country/state, tap 2. Start entering the settlement name on the keyboard. 3. Get to the list of search results: 4. x After entering a couple of characters, the names that match the string appear in a list. x Tap automatically. to open the list of results before it appears Select the settlement from the list. 4. Tap the 5. The map appears with the selected point in the middle. Tap from the Cursor menu.
4. 5. 6. Select the street from the list. Enter the house number: 1. Tap 2. Enter the house number on the keyboard. 3. Tap . to finish entering the address. The map appears with the selected point in the middle. Tap from the Cursor menu. The route is then automatically calculated, and you can start navigating. 3.1.2.
3.1.4 Selecting the destination from the POIs You can select your destination from the POIs included with ZENEC Navigation Software or from the ones you have previously created. The procedure is explained starting from the Navigation menu. , . 1. Tap the following buttons: 2. Select the area around which the POI should be searched for: x : The POI will be searched for around a given address. x : The map appears with the Cursor in the middle.
5. Tap the desired POI in the list. 6. The map appears with the selected point in the middle. Tap from the Cursor menu. The route is then automatically calculated, and you can start navigating. 3.1.5 Selecting the destination from the History The destinations that you have set earlier appear in the History. The procedure is explained starting from the Navigation menu. , . 1. Tap the following buttons: 2. If necessary, move between pages with 3. Tap the desired item. 4.
3.2 Creating a multi-point route (inserting a via point) Multi-point routes are created from simple routes, so a route must be active first. One of the ways of expanding the route is to keep the destination, and to add via points (intermediate destinations). 1. Select a new location as you did in the previous sections. This will be the additional destination in the route. 2. The map appears with the selected point in the middle, and the Cursor menu opens automatically. 3.
to open the full Cursor menu with the additional functions. 3. Tap 4. Tap to add the point as a new final destination demoting the previous one to the last intermediate destination. 5. [optional] To add more points to the route, repeat the above steps as many times as you like. Every time a new point is added, the route is recalculated automatically and you can start navigating right away. 3.4 Editing the route Tap the following buttons: , , .
4. . The simulation can be aborted any time by tapping 3.6 Pausing the active route You do not need to pause the active route: when you start driving again, ZENEC Navigation Software restarts the voice instructions from your position. 3.7 Deleting the next via point from the route The easiest way to delete the upcoming route point (the next via point) is to open the Route Information screen by tapping the Turn Preview field ( ) on the Map screen, and then tapping . You have another option.
3.9 Saving a route The procedure is explained starting from the Map screen. 1. Tap the following buttons: 2. Enter a name for the saved route, and then tap , , . . When you save a route, ZENEC Navigation Software not only saves the route points but the whole itinerary: x The saved route might have been influenced by TMC information. When you later use the route, it appears as it was saved. But if it needs to be recalculated, the current TMC information will be used in the new route.
4 Reference Guide On the following pages you will find the description of the different menu screens of ZENEC Navigation Software. The Navigation menu: ZENEC Navigation Software starts with the Navigation menu. From there you can access the following screens: Screen Button Description Map The Map screen. Find Selecting the destination (for example an address or a POI) or using the search engine of ZENEC Navigation Software for any other reason (for example to look for the phone number of a POI).
Symbol Name Trip data GPS position quality Action Opens the Trip Information screen Opens the Quick menu Top row Next street Bottom row Current street and house n/a numbers on left and right Map view modes , , Menu n/a Switches between 2D and 3D map modes: x 2D North-up x 2D rotated x 3D rotated Opens the Navigation menu Repeat Voice Instruction Repeats the last voice guidance instruction with updated distance information.
Symbol Name Action Tilt up, tilt down Tilts the 3D map Zoom in, zoom out Scales the map Return to GPS position (appears when GPS position is available and you have moved the map) Tap this button to move the map back to the current GPS position. If the map has been rotated in 3D mode, automatic map rotation is also reenabled. Enable Smart Zoom (replaces the previous button if there is no GPS position or the map has not been moved) Tap this button once to enable Smart Zoom.
4.1.1 Icons on the map There are several status icons on the map. Most of them also function as a button. The information they provide is as follows: x GPS position quality x Sound status (muted or enabled) x TMC reception and processing status 4.1.1.1 GPS position quality indicator This area is a status indicator, and also acts as a button that opens the Quick menu. GPS reception quality shows the current accuracy of the position information.
4.1.1.3 Next two route events (Turn Preview fields) There are two fields reserved on the Map screen to display the next two manoeuvres (route events that are listed in the Itinerary). Both the type of the event (turn, roundabout, exiting motorway, etc.) and its distance from the current GPS position is displayed. Most of these icons are very intuitive and you also know them as road signs. The following table lists some of the frequently shown route events.
4.1.2 Objects on the map 4.1.2.1 Streets and roads ZENEC Navigation Software shows the streets in a way that is similar to how the paper road maps show them. Their width and colours correspond to their importance: you can easily tell a motorway from a small street. Tip! If you prefer not to see street names during navigation, turn them off (page 61). 4.1.2.2 3D object types To enable or disable 3D visualisation on the map, tap the following buttons: , , , .
Symbol Name Description When you are using a saved route, ZENEC Navigation Software asks you if you want to use your GPS position or the first point in the saved route as the start point. You can also modify the start point in the Cursor menu. If you do so, automatic off-route recalculation needs to be turned off to keep the selected point as the start point.
Button Description Closes the Cursor menu, and returns to the previous screen. Zooms out the map. Zooms in the map. With the Cursor menu open, you can still move or scale the map, and tap the map anywhere to place the Cursor to a new location, but when you use this button, the Cursor jumps back to the place where it was at the time when you opened the Cursor menu. Displayed at the Cursor if it is at the same location with which the Cursor menu was opened.
Button Description If the Cursor is at or near a Pin, this button replaces the previous one, and deletes the Pin the Cursor is near to. The Cursor is saved as the location of a Road Safety Camera (speed camera or red light camera). A new screen appears where you can set the type of the camera, the direction of the measured traffic, and the speed limit checked for (if applicable).
You have the following data and functions on this screen: Name Route line Estimated Arrival Distance Left Time Left Method Warning icons Description Function The upper part of this screen shows your planned route as a horizontal line. Its leftmost point is the start of the route, the rightmost one is the final destination, and you can see your via point flags along the line, spaced in proportion to their distance.
When you open the screen, all route data fields contain information about reaching your final and the fields concerning your route display data for the next via destination. Tap point. Tap the button repeatedly to toggle between the two options. You have the following data and functions on this screen: Name Description or Shows whether the route data fields show information about the final destination (checkered flag) or about the next via point (yellow flag) .
Most of the fields on this screen have a symbol next to them. This symbol shows whether the field it is attached to is shown on the map as a Trip Data. It also shows the position of the data as follows: Symbol Description This value is not shown on the map screen. This value appears on the map screen in the Trip Data area. This is the value at the top. This value appears on the map screen in the Trip Data area. This is the value in the middle. This value appears on the map screen in the Trip Data area.
4.1.7 Quick menu The Quick menu is a selection of controls that are frequently needed during navigation. It can be opened directly from the Map screen by tapping . If you tap any of the switches in the Quick menu, the Map screen immediately returns. A switch is on if its lamp is lit. Name Main function (single tap) Function (tap and hold) If you only adjust the volume, you need to use this Opens the Navigation menu. button to return to the Map screen. Mutes all sounds of ZENEC Navigation Software.
4.1.8 GPS Data screen Tap the following buttons: to see the status of GPS reception. Icon Colour Green Yellow Grey Red , and then Name GPS position quality indicator to open the GPS Data screen and Description ZENEC Navigation Software has a connection to the GPS receiver and GPS position information is available in 3D: ZENEC Navigation Software can calculate both your horizontal and vertical GPS position.
Icon Colour Name Description ones are used by the GPS receiver to calculate your current location. Coordinates n/a Your current GPS position in WGS84 format. Dark bars are for the yellow and lit bars are for the green satellites. The more satellites your GPS tracks (the green ones), the better is your calculated position. Status bar for the satellites n/a 4.2 Find menu Select the destination of your route. Tap the following buttons: Button , .
Button Description Reference You can modify the route: remove route points or change their page 38 order. Erase the active route with all its route points (start point, via page 39 points and destination). If you later decide that you need the same route, you will have to rebuild it from scratch. You can save the active route for later use. page 40 You can load a previously saved route for navigation. page 40 You can run a demonstration of the route at normal speed.
4.4.1 Manage Saved Routes You can manage the previously saved routes. Tap the following buttons: , , . Button Description Button with the name of the saved route Opens the selected route for editing. Deletes the selected route. Clears the list of saved routes. Moves between pages for additional list items. , 4.4.2 Manage History You can manage the list of locations you used lately. Tap the following buttons: , , . Button Description Deletes the selected item in the History.
Button / Icon Description Opens the selected POI group for editing. Tap to filter the list to contain only the POIs that you saved. Tap to see all POIs in the list. Creates a new POI group at the given group level. Moves between pages for additional list items. , This POI group is not shown on the map. This POI group and all its subgroups are shown on the map. This POI group and some of its subgroups are shown on the map. This POI group contains POIs that you saved.
4.4.4 Manage Favourites You can manage the list of your Favourites. Tap the following buttons: , , . Button Button with the name of the Favourite Description Opens the selected Favourite for editing. Deletes the selected item in the list of Favourites. Clears the list of Favourites. Moves between pages for additional list items. , 4.4.5 User Data Management You can manage the data you have saved (Pins, POIs, Favourites, and History) and the settings you have made in the program.
4.5 Settings menu You can configure the program settings, and modify the behaviour of ZENEC Navigation Software. Tap the following buttons: , . The Settings menu has two pages of submenus. Tap Button to access the other options. Description Reference You can fine-tune the appearance and content of the Map page 61 screen. You can control how ZENEC Navigation Software behaves page 62 during navigation. These settings determine how routes will be calculated.
4.5.1 Map Screen settings You can fine-tune the appearance and content of the Map screen. Tap the following buttons: , . Button 3D Settings , Description Use 3D settings to determine which of the present 3D objects are shown on the map, and adjust the level of 3D visual detail. The options are as follows: x Landmarks: Landmarks are 3D artistic or block representations of prominent or well-known objects. 3D landmarks are only available in selected cities and countries.
4.5.2 Navigation settings You can control how ZENEC Navigation Software behaves during navigation. Tap the following buttons: , , . Button Keep Position on Road Description This feature allows car drivers to always correct GPS position errors by matching the vehicle position to the road network. By turning off this feature you also turn off the GPS position error filtering. The position shown on the map will be subject to all position errors and position fluctuations.
Button Description of the excluded road types, they will be used, but only as much as necessary. In this case a warning icon will be shown on the Route Information screen, and the part of the route not matching your preference will be displayed in a different colour on the map. Route Calculation Method You can choose from different route types.
Route Calculation Method types: Fast Option Description Gives the quickest possible route if you can travel at or near the speed limit on all roads. Usually the best selection for fast and normal cars. Short Gives a route that has the smallest total distance of all possible routes between the route points. Usually practical for slow vehicles.
Time and Time Zone Settings: Button Description Auto Time Correction to GPS Use this feature to synchronise the clock of your device to the highly accurate time provided by the GPS receiver. Use Auto Time Zone Use this feature to synchronise the time zone of the clock of your device to the time zone based on your current GPS position. This is useful if you travel abroad. Set Time Zone Set time zone manually if you do not want to synchronise the time zone automatically.
Button Description Baud Rate The communication speed used between the TMC receiver and the application. Tap this button and let ZENEC Navigation Software find and connect to the TMC receiver. Autodetect With a TMC receiver already connected, the content of the screen is different: Button Description Use Auto-tuner If Auto-tuner is enabled, the tuner of ZENEC Navigation Software sweeps through the FM CCIR radio band searching for a TMC signal.
5 Glossary 2D/3D GPS reception The GPS receiver uses satellite signals to calculate its (your) position and needs at least four signals to give a three-dimensional position, including elevation. Because the satellites are moving and because objects can block the signals, your GPS device might not receive four signals.
Overview mode You can instruct ZENEC Navigation Software to automatically switch to Overview mode if the next route event is in a distance. In Overview mode the map is shown in 2D but scaled down to a predefined zoom level. When you approach the next route event, the previous 2D or 3D map view returns automatically. Route A series of destinations to be reached one after the other. A simple route contains one start point and only one destination.
6 End User Licence Agreement 1 The contracting parties 1.1 This Agreement has been entered into by and between NNG Global Services LLC. (registered seat: 23 Bérc utca, H-1016 Budapest, Hungary; Company reg.no.: 01-09-913383) as Licensor (hereinafter: Licensor) and You as the User (hereinafter: User; the User and the Licensor jointly referred to as: Parties) in subject of the use of the software product specified in this Agreement. 2 Conclusion of the Agreement 2.
6.2 The User is entitled to make one backup copy of the Software Product. However, if the Software Product operates after installation without the use of the original media copy, then the original media copy shall be deemed to be a backup copy. In all other cases, the User is only entitled to use the backup copy if the original media copy of the Software Product has been ascertainably and unequivocally rendered unsuitable for its lawful and intended use. 7 Limitations of use 7.1 The User is not entitled 7.
9.1 The Licensor hereby informs the User that, if the Licensor finds its rights under the Copyright Act to be breached, the Licensor may 9.1.1 seek judicial recognition of this breach; 9.1.2 demand that the breach cease and order the person in breach to refrain from continuing such actions; 9.1.3 demand that the person under breach give proper compensation (even by way of publicity at the expense of the person in breach); 9.1.4 claim the return of the increase of assets due to the breach; 9.1.
72 ZE-NA2000_UserManual_UK.indd 72 23.04.
ZE-NA2000_UserManual_UK.indd 73 23.04.
MODEL NO: ZE-DVBT1 0 1 CH DVB-T TUNER ZENEC · By ACR AG · Bohrturmweg 1 · Bad Zurzach · Switzerland ZE-NA2000_UserManual_UK.indd 74 23.04.