Installation Guide

ManualsBrandsZenith ManualsBathroom97-in H Steel Chrome Tension Pole Freestanding Shower Caddy

Pg 1 of 7

www.zennahome.com IS3221-I4

MCS 5/13/2016

Assembly Instructions - Model 2132HB (Bronze) / 2132S (Chrome)

Instrucciones de Ensamblado - Modelo 2132HB (Bronce) / 2132S (Cromo)

Instructions de montage - Modèle 2132HB (Bronze) / 2132S (Chromé

)

Before You Begin:

Thank you for purchasing this product. Please identify all parts and hardware pieces before you begin.

When laying out parts, place them on a soft surface to prevent scratching.

If any pieces are missing, call our Toll Free Number 1-800-892-3986 between 8:00AM-5:00PM EST Monday

through Friday or contact our website at www.zennahome.com for more information.

Antes de que empiece:

Muchas gracias por comprar este

producto.

Identifique todas las piezas y las piezas de ferretería antes de

comenzar. Al distribuir las piezas, colóquelas sobre una superficie suave para evitar que se rayen.

Si faltaran piezas, llame a nuestro número gratuito 1-800-892-3986 entre las 8:00 a.m.- 5:00 p.m., hora

del este, de lunes a viernes o contáctenos a través de nuestro sitio web en www.zennahome.com para

solicitar mas información.

Avant de commencer :

Merci d’avoir acheté ce produit. Veuillez identifier toutes les pièces et les accessoires de montage avant de

commencer. Lorsque vous déballez les pièces, placez-les sur une surface non rugueuse afin d’éviter les

éraflures.

S’il venait à vous manquer des pièces, appelez notre numéro sans frais 1.800.892.3986 entre 8 h et 17 h

(heure de l’Est des États-Unis), du lundi au vendredi, ou contactez notre site Web à www.zennahome.com

pour de plus amples informations.

Summary of content (7 pages)

PAGE 1
Assembly Instructions - Model 2132HB (Bronze) / 2132S (Chrome) Instrucciones de Ensamblado - Modelo 2132HB (Bronce) / 2132S (Cromo) Instructions de montage - Modèle 2132HB (Bronze) / 2132S (Chromé) Before You Begin: Thank you for purchasing this product. Please identify all parts and hardware pieces before you begin. When laying out parts, place them on a soft surface to prevent scratching.
PAGE 2
List of Parts: Lista de Partes: Liste des pièces : (A) 1 Straight tube (with spring packed inside) 1 Tubo recto (resorte empacado dentro del tubo) 1 tube droit (ressort à l'intérieur du tube) (D) 1 Short tapered tube 1 Tubo corto con ahusamiento 1 tube conique court (B) 2 Long tapered tubes 2 Tubos largos con ahusamiento 2 longs tubes coniques (C) 1 1/2” diameter tube 1 Tubo con diámetro de ½" 1 tube de 12,7 mm (1/2 po) de diamètre (E) 3 Shelves 3 Repisas 3 étagères métalliques (H) 2 Plastic T-caps 2
PAGE 3
1. NOTE: No matter the distance tubes (A) and (C), are ALWAYS used. Measure the distance between the tub ledge or the shower stall floor to the ceiling to the nearest inch. See chart to know what tubes (B) and (D) that are needed. REMARQUE : quelle que soit la distance, les tubes (A) et (C) sont TOUJOURS utilisés. Mida la distancia entre el reborde de la bañera o el piso del cubículo de la ducha hasta el cielorraso redondeando a la siguiente pulgada.
PAGE 4
2.NOTE: Assembly shown for 92 - 97 in. installation. Place a wedge (G) (tapered or rounded end up) on one of the long tapered tubes (B) approximately half way down. Slide shelf with towel bar (F) down the tube and fit over the wedge. Repeat process for one of the middle shelves (E). Shelves can be adjusted by moving the wedges up or down. Repeat process for other long tapered tube (B) and other shelves (E). NOTA: Ensamble mostrado para instalación de 92 a 97 pulgadas.
PAGE 5
3.Place the tapered end of the tube with the two shelves on it into the untapered end of the other tube with the shelves on it. Coloque el extremo con ahusamiento del tubo con las dos repisas dentro del extremo sin ahusamiento del tubo con el ensamble de gabinete en él. B Enfilez l'extrémité conique du tube muni des deux étagères dans l'extrémité non conique du tube supportant le serviteur. B 4.Place the straight tube (with spring packed inside) (A) on top of the assembly.
PAGE 6
5.Slide the plastic end cap with hole (J) on the 1/2” tube (C). Place a T-cap (H) on each end of the 1/2” tube (C). H Deslice la cubierta terminal de plástico con orificio (J) en el tubo de ½" (C). Coloque una cubierta en forma de "T" (H) en cada extremo del tubo de ½" (C). C Enfilez l'embout en plastique perforé (J) dans le tube de 12,7 mm (1/2 po) (C). Placez ensuite un embout en T (H) à chaque extrémité de ce tube (C). J H 6.
PAGE 7
. 1. Slip the tapered end of the short tapered tube (D) into the untapered end of the bottom tube of the assembly. Place the soft vinyl end cap (I) on the bottom of the assembly. 2. Place the tape strips (K) around the seams of the tubes. (This will protect the tubes from moisture.) 3. Lift the entire assembly into position over the tub ledge or shower stall floor. 4. Compress top of unit against the ceiling at desired location. Move the bottom end into place so that the unit is in a vertical position. 1.