SERVICE MANUAL Product Type: HD PERSONAL VIDEO RECORDER & RECEIVER Manual Series: HDR230 Manual Part #: 3829RVN006M Model Line: A Product Year: 2003 CONTENTS Summary .................................................... 1 Exploded View ........................................... 2 Electrical .................................................... 3 Parts List ....................................................
SECTION 1 SUMMARY CONTENTS OVERVIEW................................................................................................................1-2 PRODUCT SAFETY SERVICING GUIDELINES FOR VIDEO PRODUCTS............1-3 SERVICING PRECAUTIONS....................................................................................1-4 SPECIFICATIONS .....................................................................................................1-5 LOCATION OF CUSTOMER CONTROLS ...............................
OVERVIEW 1.1 Explanation - HD PERSONAL VIDEO RECORDER & RECEIVER or PVR(Personal Video Recorder)-STB(Set-Top Box) stores video and audio data into HDD with a specific form while receiving the ground wave of HD digital broadcasting only or gives additional related services. - Configuration It uses IBM PPC405GP of PowerPC series as CPU, which supports PCI Bus I/F for PVR.
PRODUCT SAFETY SERVICING GUIDELINES FOR VIDEO PRODUCTS IMPORTANT SAFETY NOTICE A.C. Voltmeter This manual was prepared for use only by properly trained audio-video service technicians. When servicing this product, under no circumstances should the original design be modified or altered without permission from Zenith Electronics Corporation.
SERVICING PRECAUTIONS CAUTION: Before servicing the HD PERSONAL VIDEO RECORDER & RECEIVER covered by this service data and its supplements and addends, read and follow the SAFETY PRECAUTIONS. NOTE: if unforeseen circumstances create conflict between the following servicing precautions and any of the safety precautions in this publications, always follow the safety precautions.
SPECIFICATIONS Television System Channel Coverage Input/ Output ATSC ANT Input ANT Loop Out Component Video Output NTSC, DTV standard (1080i, 720p, 480p, 480i) Terrestrial: 2-69, Cable: 1-125 Digital Audio Output Analog Audio Output Authorized Service Port ANT IN (1) (ATSC-8VSB over CATV or Terrestrial) Out To TV (1) Component Out (1), Typical RCA Jack Connectors 1080i, 720p, 480p YPbPr RGB Out(1), 15-Pin connector S-Video Out (1), 4-pin Mini-DIN 480i Y/C Video Out (1), Typical RCA Jack Connectors 480i C
LOCATION OF CUSTOMER CONTROLS FRONT Arrow Buttons ( / / / EXIT SELECT ) GUIDE MENU RECORD DISPLAY FORMAT Power Remote Control Sensor Standby indicator Disk Full indicator Display format indicator Reserved REC indicator Record indicator REAR ANT LOOP OUT OUTPUT SELECTION OPTICAL (Digital audio out jack) VIDEO OUT COAXIAL (Digital audio out jack) YPbPr OUT AUTHORIZED SERVICE ONLY RGB OUT ANT IN AC Power Cord AUDIO OUT (Left/Right) S-VIDEO OUT 1-6
REMOTE CONTROL Mode indicator TV/INPUT POWER MODE MENU CC SIGNAL RATIO SURF INFO Numbers Dash (-) SELECT ( MUTE VOL(Volume) (+/-) CH (Channel) (+/-) FLASHBK ) GUIDE RESERVED REC PROGRAM LIST REPEAT RECORD/EDIT STOP REPLAY LIVE TV/END Arrow Buttons ( (SELECT) PAUSE PLAY/SLOW FF REW TIMESHIFT EXIT Component Control Buttons 1-7 / / / )
SECTION 2 CABINET & MAIN CHASSIS CONTENTS EXPLODED VIEWS .....................................................................................................................2-2 1. Cabinet and Main Frame Section ...........................................................................................2-2 2. Packing Accessory Section ....................................................................................................
EXPLODED VIEWS 1. Cabinet and Main Frame Section NOTE) Refer to “SECTION 4 REPLACEMENT PARTS LIST” in order to look for the part number of each part.
2.
SECTION 3 ELECTRICAL CONTENTS 1. WIRING DIAGRAM.............................................3-2 2. SYSTEM S/W UP-DATE & DIAGNOSTIC S/W..3-3 3. ELECTRICAL TROUBLESHOOTING GUIDE .................................................................3-7 1) INITIAL...........................................................3-7 2) POWER(SMPS) PART ..................................3-8 3) SYSTEM PART............................................3-10 4) VIDEO PART................................................
1. WIRING DIAGRAM Main Power Connector Power On Live +5V GND +12V GND +12V GND +3.3V +3.3V +3.3V GND +5V +5V GND +5.5V Power Board Digital Board Total :15 Line HDD I/F Connector DATA[0~15] 16 +5.
2. SYSTEM S/W UP-DATE & DIAGNOSTIC S/W • System S/W Up-date 1) Connect the serial cable between the connector for a service and the serial port of PC, and run TeraTerm Program on the PC. 2) Switch to System Code Up-data mode by press select key and left Volume(F ) key together at the front. 3) TeraTerm screen - “Preparation for S/W Up-data is completed” message is displayed on the screen. - Select ‘Send file’ from File menu of TeraTerm and select the file for Up-data.
• Using Diagnostic S/W Preparation for diagnostic using test code stored at flash memory 1) At Power Up, connect the serial cable to the port for a service, place the cursor on TeraTerm screen, and turn the power of HDR230 on with “Shift+T” of the PC keyboard pressed.
Screen shot during Test Run the test by press “ T” and then “Enter” key ============================System Test============================== System SDRAM Test----------------------------->OK(32MB) Flash Memory Test Start ....
Screen shot during Test *************************System Test Result************************** 01. System SDRAM Test------------------------------>OK 02. Flash Memory Test--------------------------------->OK 03. HD1 Test---------------------------------------------->OK 04. Audio Decoder Test-------------------------------->OK 05. HD1 DMA Test-------------------------------------->OK 06 .I2C EEPROM Test--------------------------------->OK 07. VSB Test---------------------------------------------->OK 08.
3. ELECTRICAL TROUBLESHOOTING GUIDE 1) INITIAL Front Power LED is red? Power LED Lights red No Check whether the power cord is connected Yes Turn on the power switch or Turn on the power switch of the remote control Yes Power LED Is flashing green repeatedly for a specific time No Check whether the battery is correctly inserted into the remote control Yes Channel number is displayed on the screen.
2) POWER(SMPS) PART (1) No 5.0VA (2) No 5.4V NO 5.0VA. NO 5.4V. YES Is the F101 normal? YES NO Is Vcc (5.6v) approved NO to Q151 Emitter? Replace the F101. (Use the same Fuse) YES Is the BD101 normal? YES NO Replace the BD101. Is Q152 Collector is GND potential? YES Is the TH01 normal? YES NO Check or Replace the Q151. Replace the TH01. YES Is Vcc (14~22v) approved NO to IC101 PIN3? YES Is the D102 normal? NO Check or Replace the D102. Are the D121 normal? NO Replace the D121.
(3) No 3.3V (4) No 12V NO 3.3V. NO 12V. YES YES Is there about 3.5V at NO the IC155/IC156 Pin1? Is there about 14V at NO the IC157/IC158 Pin1? Check or Replace the D123/D124. YES Is there about 4.5~5V at the IC155/IC156 Pin1? Check or Replace the D125/D126. YES NO Check the µ-com pin PWR CTL signal Is there about 4.5~5V at the IC157/IC158 Pin4? YES YES Check or Replace the IC155/IC156. Check or Replace the Q157/IC158.
3) SYSTEM PART When the screen is not displayed after the power is turned on Check with the terminal after Check the terminal message connecting the test cable to by using Password “debugLST2400” the port for a service Check whether 3.3V is supplied at Power Connector 8,9,10-Pin Yes Operating normally at the terminal No Yes Check 2.5V output at 3-pin of CPU power IC155 No Yes Check whether the clock of 33.
4) VIDEO PART Component signal is missing yes Normal RGB output No Pr signal : Check whether the signal is flown or not J118.13-> F111-> R472 -> C474 -> IC152.7 Check whether R431 and R432 have bad soldering No Pb signal : Check whether the signal is flown or not J118.15-> F113-> R476 -> C476 -> IC152.8 Check whether R445 and R446 have bad soldering no Check whether L122 terminal is +9V Check whether R507, R508, R244, R245 and R246 have bad soldering No Pr signal : Check whether there exists Q114.
RGB signal is missing yes Component port Normal output? no Check the direction of IC151 Check IC151.4 -> 9V, IC151.11 -> ground Check whether there exists Pin 7, 8 and 12 signals of IC151 from VGA connector Red : J111.1 -> F106 -> R471 -> C471 Green : J111.2 -> F107 -> R473 -> C472 Blue : Check J111.3 -> F108 -> R474 -> C473 signal Check whether R429, R430, R439, R440, R441 and R442 have bad soldering Check L122 terminal is +9V.
A/V Out port No video screen signal no S-video port No signal Check J118.5 -> F114 -> R467 -> C742 -> C741->R746-> R737->Q709->L709->R723->Q706->R728 signal. Check whether Q703.base is Low(0V) (Mute Off) Check whether L112 terminal is +9V yes yes RGB/YPbPr Normal output? no yes No S-video screen color Check Front Display format LED System error Check F118 -> R478 -> C746->IC165.7->C744->R748-> R739->Q711->L711->R725->Q708 terminal C_OUT signal.
5) AUDIO PART When there is no sound after the power is normally turned on, Video is normally displayed Check whether the rear audio output terminal is correctly connected to TV or AMP Check whether the input is correctly selected No Check whether the volume of TV or AMP is correctly selected Yes Check whether the volume is correctly selected No Control the volume.
6) VSB PART When the screen is not displayed or distorted LED103 : On LED104 : Off LED103 : Off LED104 : On LED103 : Flashing LED104 : On See ‘Video’ of 3.3 Troubleshooting guide Is the channel on air selected? Did you check the clock used at IC146 and IC156? Did you check the power used at each part by referring to the block diagram? Did you select the channel on air? Check the clock by referring to VSB section of 3.4 Wiring diagram and Waveform.
7) PVR PART When TV is normally operated but PVR does not function "PVR function doesn't work properly" of the SETUP menu. Error code = 121 Yes Check PCI Clock Check 33.33MHz output at IC102 8-Pin No Error code = 124 No Check HDD Cable and HDD Power Cable connection Error code = 125 Error code = 131 Check PCI Clock Check 33.
5. VOLTAGE MEASURED VALUE 1) CAPACITOR Capacity 0.47uF 1uF 10uF/16 Circuit No. C746 C288 C289 C398 C454 C455 C456 C457 C458 C100 C101 C107 C110 C207 C208 C209 C210 C213 C226 C254 C269 C272 C283 C293 C295 C297 C336 C357 C358 C397 C483 C484 C488 C492 C493 C496 C500 C503 C507 C511 C700 C705 C725 DTV (+) 3.158 4.79 2.24 7.03 3.5 0 4.96 7.81 6.64 2.48 2.48 3.23 3.23 3.23 3.23 3.23 2.44 2.44 1.68 9.04 9.04 9.04 4.95 9.04 4.95 4.54 3.23 3.23 3.23 7.03 5.04 12.25 3.23 4.96 4.96 2.52 3.22 5.04 9.02 5.81 0 5.36 3.
Capacity 22uF/16 47uF 100uF 220uF Circuit No. C739 C211 C212 C249 C250 C299 C302 C305 C306 C369 C379 C380 C383 C385 C386 C395 C412 C428 C441 C443 C497 C505 C510 C704 C278 C279 C301 C310 C318 C600 C607 C244 C487 C489 C490 C495 C509 C609 C237 C252 C393 C394 C712 DTV (+) 4.78 3.22 2.43 4.5 4.5 3.86 3.86 4.61 4.61 3.23 12.26 5.79 5.04 5.03 9.01 9.01 2.43 3.24 12.25 9.05 2.5 9.03 9.02 2.41 4.59 4.59 8.74 3.23 3.23 5.04 5.03 3.13 3.24 4.96 3.24 2.52 9.02 5.03 3.19 3.23 5 5.01 4.92 PVR (-) 0 0 0 2.31 2.
Capacity 470uF Circuit No. C273 C451 C452 C453 C471 C472 C473 C474 C475 C476 C741 C742 C743 C747 DTV (+) 3.23 2.26 2.26 2.26 4.53 4.53 4.53 4.53 4.53 4.53 1.748 3.43 1.796 3.201 PVR (-) 0 0.98 0.98 0.98 0 0 0 0 0 0 0 0 0 0 Top/Bottom 3.22 2.23 2.23 2.24 4.53 4.53 4.53 4.53 4.53 4.53 1.748 3.431 1.796 3.202 3-37 Top/Bottom 0 1.17 1.17 1.16 0.2 1.3 0.
2) DIODE Capacity SD05 LED Circuit No. D100 D101 D102 D103 D104 D105 D106 D107 D108 D119 D120 D121 D122 D123 D124 D125 D126 D127 D128 D129 D131 D132 D133 D134 D135 D136 D137 D138 D140 D141 D142 D143 D144 D145 D146 D147 D148 LED103 LED104 LED105 DTV (+) 0 -0.75 0.09 3.23 3.23 3.23 3.23 3.09 3.2 0 0 0 0 0 0 2.77 0 2.77 0.11 2.77 0.11 1.64 -0.718 2.77 2.77 2.77 0.11 2.77 0.18 0.011 0.09 3.17 3.17 3.2 3.17 3.17 0.008 2.8 0.17 0 PVR (-) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 2.77 0 0 0 0 0 0 3.22 3.22 3.22 2.94 3.
Circuit No. Part Name Circuit No. SLUV2.8 D109 D110 D111 D112 D113 D114 D115 D116 D117 1 PVR 2 0 0 0 0 0 0 0 0 0 3 0.33 0.24 0.27 0.01 0 0.01 0.15 0 0.08 1 2 0 0 0 0 0 0 0 0 0 3 0 0 0 0 0 0 0 0 0 Reference Item Video Signal 3) TRANSISTOR Part Name Circuit No. KRC101S Q703 Q704 Q705 KTA1504 Q114 Q115 Q116 Q706 Q707 Q708 Q709 Q710 Q711 KTC3875 Q108 Q109 Q110 Q111 BF799W Q112 Q113 KRA102S Q102 Q103 Q104 Q105 KRC102S Q119 Q120 Q121 Q702 BSS83 Q100 Q101 Circuit No. E(S) 0 0 0 2.05 1.97 1.95 1.51 1.
9. REFERENCE 1) RESET BLOCK DIAGRAM +3.
2) POWER BLOCK DIAGRAM PVR Digital Board IC141 +12V Regulator 7809 Power Suppl ier +5V Tuner TDPC-H901P IC143 +9V SAW Filter & RF TR IC144 IC147 Down Converter IC156 +5V +5.4V Regulator 78R05 IC161 Power_On Live_+5V +3.3V IC146 VSB Chip GND LGDT3102 +12V +12V UPC2798 System Memory GND +12V +3.3V-1 Regulator +2.5V EZ1580 IC155 +3.3V-1 +3.3V GND CPU [PPC405GP] IC100 HD-1 +3.3V Flash Memory [29F323TE] +5V +5V GND Flash Memory [29F323TE] IC109 IC108 System CPLD [EPM3128A] +5.
4.
2) DIGITAL SYSTEM [SYSTEM MEMORY] PART 2 1 3 3-19 3-20
3) VIDEO [PLL] PART 2 1 3-21 3-22
4) VIDEO [OUTPUT CONNECTOR] PART BMK800 BMK800 33PF 33PF 33PF BMK800 3 1 2 3-23 3-24
5) AUDIO PART 2 1 3 /STI4600_RESET R775 Q712 KRA102S R774 Q713 3:K7 CA_SPDIF_MUTE 22 DGND 3-25 3-26 4
6) PVR [CLOCK] PART 2 1 3 3-27 3-28
7) VSB [VSB DECODER] PART 1 3-29 3-30
8) VSB [DOWN CONVERTER] PART 1 3-31 3-32
9) MICOM [DOWN CONVERTER] PART 1 3-33 3-34
6. BLOCK DIAGRAMS 1) OVERALL BLOCK DIAGRAM 16(32)MByte SDRAM SDRAM (2Mx32Bit) (2Mx32Bit) VSB Tuner (ATSC) SAW Filter External PLL/VCXO Glue Logic SDRAM SDRAM (2Mx32Bit) (2Mx32Bit) Coaxial SPDIF out 128-Bit I/F Audio Decoder HD-1 F Conn. Spliter I2C_A Down Converter VSB Decoder -TP De-Mux -MPEG Decoding : MP@HL -Format Converter -Host I/F, Memory I/F -Digital I/F -Video DAC, NTSC Encoder VSB TP TP MUX RCA Conn. I2C_C - Dolby AC -3 - MPEG Audio - SPDIF Out ITU-R.
2) POWER BLOCK DIAGRAM 2 18 4 16 17 12V REG BLOCK (IC157, IC158, R156 R157, C155, C156) (D125, D126, C128 C126, L122, C130) TO HDD 5V 12V 3.3V REG S/W BLOCK 7 14 15 (IC155, IC156, R154 R155, R159, R158 C154) (D123, D124, C125, C126, L123, C127) From Main PWR ON/OFF 13 5VA REG BLOCK 12 (IC152, C152) 8 10 11 5V REG & S/W BLOCK (D121, C122 L121, C124) (IC151, R151, C151) 5.4V S/W BLOCK (Q151, R160, R161 R162, Q152, R152 R153, C157) 3-42 3-43 TO MAIN 5.0VA 12V 5.0V 3.3V 5.
3) SYSTEM BLOCK DIAGRAM 32Mbyte System Memor y PCI_Bus 16Mbyte 33.3MHz- 1 16Mbyte 8M x 16 (4 bank ) OCM Ctrl Timers I-OCM MMU D-OCM Arb Interrupt Control PPC405GP [456-PBGA, 2.5V, 3.3V] Clock Generator ICS387 33.3MHz- 1 33.3MHz- 2 12MHz Ethernet MAL DMA Ctrl 100MHz Processor Bus(PLB) 64-bit Code Decompression SDRAM Controller SRAM/ROM Peripheral Controller External Bus Master Controller OPB Bridge On-chip Peripheral BUS(OPB) 14.
4) VIDEO BLOCK DIAGRAM RGB HD 1 Chip Audio & Data I/F PES output to AC-Decoder TP Input VSB Chip TP Input PDR-Pro Chip 74CBTLV 16292 Mux MP@HL Video Decoder Multi-stream Format Converter & Display Controller Post Processing CSC & LUT 2-D Graphics & OSD BP Filter DAC x3 BP Filter PWM Gen.
5) VIDEO PLL BLOCK DIAGRAM HD-1 VDP_CLK 27MHz AC-3 Decoder Clock 74.175MHz or 81MHz 74LCX 253 27MHz SYS_CLK S1 NTSC_CLK ICS621M Clock Buffer 49FCT 3805 Clock Buffer MAIN_PWM Clock Synthesis Control Clock Synthesis Control S0 Output Buffer Output Buffer Output Buffer VCXO 27MHz 81MHz FR_RATE60 74.
6) AUDIO BLOCK DIAGRAM STi4600 AC -3 Decoder PPC405GP CPU Per_Data[0:7] Per_Addr[0:7] /CS6 PER_RW /PER_OE /RQ4 Data Address System CPLD /CS /RD /WR REQ MCLK SCLK LRCLK PCM_OUT0 27MHz HD-1 PLL CS4340 Audio DAC PCMCLK Per_Data[0:7] Per_Addr[0:4] Per_Addr[20:23] HD-1 Address Data Decoder TDA7440D Volume Controller SIN LRCLKIN STR REQ Variable(or fixed) Audio L/R Out MC33078 OP AMP Audio Mute I2C Bus_B IE958_OUT PES0_DATA PES0_STROBE 74LCX157 Mux PES0_REQ Audio Mute DS8921 422 Driver 35101
7) TUNER/VSB & MICOM BLOCK DIAGRAM VSB DTV Tuner TDPC-H901P 5V X-Tal OSC 38MH z 25MH z I2C_A RF Spliter SAW Filter IF In USP-NT-012 X6965D IF Amplifier IF Amplifier BF799 BF799 SAW Filter X6931D I2C_C Down Converter VSB Decoder Error_LED UPC2798 LGDT3102 Lock_LED VSB_Reset L_5V 12V 5.4V 9V Regulator 7809 9V Regulator 78R05 5V +5V +3.3V VSB TP out 8MHz Power Switch TP out +2.5V Front Switch Front I/F Conn. LED LED Driver TR Front I/F Conn.
8) PVR BLOCK DIAGRAM E-IDE I/F Connector PCI-IDE Controller PCI0649 33MHz VSB_TP[0:7] & Control Signals from VSB part PCI Bus TP_OUT[0:7] & Control Signals TP_OUT[0:7] & Control Signals to HD-1 PDR-Pro PVR CPLD VSB_ TP[0:7] &CLK HDD PCI I/F Signals From CPU 304 PQFP [EPM3128A] DATA_A [0: 31] UP SDRAM 2Mx32bit [K4S643232] ADR_A [0:10] DATA_B [0: 31] ADR_B [0:10] FIFO 512byte [IDT72V211] DN SDRAM 2Mx32bit [K4S643232] 3-54 3-55
7. CIRCUIT DIAGRAMS 1) POWER CIRCUIT DIAGRAM No power. BD101, TH01 are defective. 12VA no power. D125/D126 are defective. 3.3V no power. D123/D124 are defective. 5.4V, 5.0V/5.0VA no power. D121 is defective. 330µF Switching Error. IC101 is defective. Switching Error. IC102, IC103 are defective. No Power. F101 is defective. _OPTIONAL PART 100Ω '03. 3. 15 HDR230 NOTES) Symbol denotes AC ground. NOTES) Symbol denotes DC chassis ground.
2) SYSTEM CIRCUIT DIAGRAM 1 PCI BUS PER_DATA PER_ADDR CPU CLOCK SMEM_DATA '03. 3.
3) SYSTEM CIRCUIT DIAGRAM 2 PC_MUTE 11 : B5 CA_SPDIF_MUTE /SYS_RESET_2 /STI4600_RESET 7 : B5 3:J2:5:B5:F2 7:A4 TO CPU P8, P9 '03. 3.
4) SYSTEM CIRCUIT DIAGRAM 3 S MEM DATA S MEM ADDR '03. 3.
5) VIDEO CIRCUIT DIAGRAM 1 27 PER-ADDR PER-DATA Valid TP DATA/CLK '03. 3.
6) VIDEO CIRCUIT DIAGRAM 2 PER-ADDR '03. 3.
7) AUDIO CIRCUIT DIAGRAM /STI4600_RESET R775 Q712 KRA102S R774 Q713 3:K7 CA_SPDIF_MUTE 22 DGND PER-DATA PER-ADDR DIGITAL AUDIO P6 ANALOG AUDIO P11 PES P5 '03. 3.
8) PVR CIRCUIT DIAGRAM 1 PCI CLOCK PCI BUS(P2) VSBIN TP DATA,CLOCK,VALID '03. 3.
9) PVR CIRCUIT DIAGRAM 2 VSB TP(Clock,valid,data) PDR TP(Clock,valid,data) VSBN TP(Clock,valid,data) CLOCK P3 '03. 3. 15 HDR230 PCI BUS(P.
10) VSB CIRCUIT DIAGRAM DNS IF '03. 3.
11) AUDIO/VIDEO OUTPUT CIRCUIT DIAGRAM BMK800 BMK800 BMK800 BMK800 BMK800 C768 DNS R772 DNS PC_MUTE BMK800 R773 DNS BMK800 P B Y.OUT Pr Pb G FROM P.7 C.OUT CVBS OUT Y D RGB HS/D RGB HS 33PF 33PF 33PF 33PF 33PF BMK800 '03. 3.
12) POWER, IF, µ-COM, VIDEO CIRCUIT DIAGRAM Y.OUT '03. 3. 15 HDR230 C.
13) FRONT CIRCUIT DIAGRAM LEFT RIGHT '03. 3.
8.
2) DIGITAL MAIN PRINTED CIRCUIT DIAGRAMS(BOTTOM) 3-84 3-85
3) KEY(LEFT) PRINTED CIRCUIT DIAGRAM 4) KEY(RIGHT) PRINTED CIRCUIT DIAGRAM LOCATION GUIDE 3-86 3-87
5) POWER PRINTED CIRCUIT DIAGRAM LOCATION GUIDDE 3-88 3-89
NOTES) NOTES) NOTES) NOTES) Warning Parts that are shaded are critical With respect to risk of fire or electricial shock. SECTION 4 REPLACEMENT PARTS LIST MODEL:(A)HDR230(ZENITH) RUN DATE:MAR.13.2003 NSP:Not Service Part .CABINET & MAIN FRAME SECTION S AL LOCA.
.ELECTRICAL SECTION S AL LOCA.NO PART NO(LG) A DESCRIPTION SPECIFICATION C100 0CH8106F611 O CAPACITOR,CHIP[AL. ELECTROLYTI 10UF 16V M 85STD(CYL) R/TP C101 0CH8106F611 O CAPACITOR,CHIP[AL. ELECTROLYTI 10UF 16V M 85STD(CYL) R/TP C101 624-088F O CAPACITOR,DRAWING PCX2 275V 0.1UF,M (PILKO) C102 0CH1104K512 O CAPACITOR,FIXED CERAMIC(Temp.c 0.1UF 50V 10% B(5YP) 1608 R/TP C102 624-088F O CAPACITOR,DRAWING PCX2 275V 0.
S AL LOCA.NO PART NO(LG) A DESCRIPTION SPECIFICATION C138 0CH1104K512 O CAPACITOR,FIXED CERAMIC(Temp.c 0.1UF 50V 10% B(5YP) 1608 R/TP C139 0CH1104K512 O CAPACITOR,FIXED CERAMIC(Temp.c 0.1UF 50V 10% B(5YP) 1608 R/TP C140 0CH1104K512 O CAPACITOR,FIXED CERAMIC(Temp.c 0.1UF 50V 10% B(5YP) 1608 R/TP C141 0CH1104K512 O CAPACITOR,FIXED CERAMIC(Temp.c 0.1UF 50V 10% B(5YP) 1608 R/TP C142 0CH1104K512 O CAPACITOR,FIXED CERAMIC(Temp.c 0.
S AL LOCA.NO PART NO(LG) A DESCRIPTION SPECIFICATION C189 0CH1104K512 O CAPACITOR,FIXED CERAMIC(Temp.c 0.1UF 50V 10% B(5YP) 1608 R/TP C190 0CH1104K512 O CAPACITOR,FIXED CERAMIC(Temp.c 0.1UF 50V 10% B(5YP) 1608 R/TP C191 0CH1104K512 O CAPACITOR,FIXED CERAMIC(Temp.c 0.1UF 50V 10% B(5YP) 1608 R/TP C192 0CH1104K512 O CAPACITOR,FIXED CERAMIC(Temp.c 0.1UF 50V 10% B(5YP) 1608 R/TP C193 0CH1104K512 O CAPACITOR,FIXED CERAMIC(Temp.c 0.
S AL LOCA.NO PART NO(LG) A DESCRIPTION SPECIFICATION C258 0CC102CK41A O CAPACITOR,FIXED CERAMIC(TEMP.C 1000PF 1608 50V 5% R/TP NP0 C259 0CH4151K412 O CAPA,CHIP CERAMIC M/L T.C F/S 150P 50V J COG 1.6X0.8 R/TP C260 0CH1104K512 O CAPACITOR,FIXED CERAMIC(Temp.c 0.1UF 50V 10% B(5YP) 1608 R/TP C261 0CC100CK41A O CAPACITOR,FIXED CERAMIC(Temp.c 10PF 1608 50V 5% R/TP NP0 C262 0CH1104K512 O CAPACITOR,FIXED CERAMIC(Temp.c 0.
S AL LOCA.NO PART NO(LG) A DESCRIPTION SPECIFICATION C315 0CH1104K512 O CAPACITOR,FIXED CERAMIC(Temp.c 0.1UF 50V 10% B(5YP) 1608 R/TP C316 0CH1104K512 O CAPACITOR,FIXED CERAMIC(Temp.c 0.1UF 50V 10% B(5YP) 1608 R/TP C317 0CH1104K512 O CAPACITOR,FIXED CERAMIC(Temp.c 0.1UF 50V 10% B(5YP) 1608 R/TP C318 0CE476SF6DC O CAPACITOR,FIXED ELECTROLYTIC 47UF MVG 16V 20% SMD R/TP C319 0CH1104K512 O CAPACITOR,FIXED CERAMIC(Temp.c 0.
S AL LOCA.NO PART NO(LG) A DESCRIPTION SPECIFICATION C372 0CH1104K512 O CAPACITOR,FIXED CERAMIC(Temp.c 0.1UF 50V 10% B(5YP) 1608 R/TP C373 0CH1104K512 O CAPACITOR,FIXED CERAMIC(Temp.c 0.1UF 50V 10% B(5YP) 1608 R/TP C374 0CH1104K512 O CAPACITOR,FIXED CERAMIC(Temp.c 0.1UF 50V 10% B(5YP) 1608 R/TP C375 0CH1104K512 O CAPACITOR,FIXED CERAMIC(Temp.c 0.1UF 50V 10% B(5YP) 1608 R/TP C376 0CH1104K512 O CAPACITOR,FIXED CERAMIC(Temp.c 0.
S AL LOCA.NO PART NO(LG) A DESCRIPTION SPECIFICATION C442 0CH1104K512 O CAPACITOR,FIXED CERAMIC(Temp.c 0.1UF 50V 10% B(5YP) 1608 R/TP C443 0CE226SF6DC O CAPACITOR,FIXED ELECTROLYTIC 22UF MVG 16V 20% SMD R/TP C444 0CH1104K512 O CAPACITOR,FIXED CERAMIC(Temp.c 0.
S AL LOCA.NO PART NO(LG) A DESCRIPTION SPECIFICATION C521 0CH4151K412 O CAPA,CHIP CERAMIC M/L T.C F/S 150P 50V J COG 1.6X0.8 R/TP C522 0CH4151K412 O CAPA,CHIP CERAMIC M/L T.C F/S 150P 50V J COG 1.6X0.8 R/TP C600 0CE476SF6DC O CAPACITOR,FIXED ELECTROLYTIC 47UF MVG 16V 20% SMD R/TP C601 0CH4200K412 O CAPACITOR,FIXED CERAMIC(High d 20PF 50V 5% NP0 1608 R/TP C602 0CH1104K512 O CAPACITOR,FIXED CERAMIC(Temp.c 0.
S AL LOCA.NO PART NO(LG) A DESCRIPTION SPECIFICATION C762 0CH4330K412 O CAPACITOR,CHIP[CERAMIC M/L TC 33P 50V J COG 1.6X0.8 R/TP C763 0CH4330K412 O CAPACITOR,CHIP[CERAMIC M/L TC 33P 50V J COG 1.6X0.8 R/TP C764 0CH4330K412 O CAPACITOR,CHIP[CERAMIC M/L TC 33P 50V J COG 1.6X0.8 R/TP C766 0CH1103K562 O CAPACITOR,FIXED CERAMIC(Temp.c 0.01UF 50V 10% X7R(X) 1608 R/T C769 0CH1104K512 O CAPACITOR,FIXED CERAMIC(Temp.c 0.
S AL LOCA.NO PART NO(LG) A DESCRIPTION SPECIFICATION D143 0DR050008AA O DIODE,RECTIFIERS SD05.TC R/TP SEMTECH SOD323 5V D144 0DR050008AA O DIODE,RECTIFIERS SD05.TC R/TP SEMTECH SOD323 5V D145 0DR050008AA O DIODE,RECTIFIERS SD05.TC R/TP SEMTECH SOD323 5V D146 0DR050008AA O DIODE,RECTIFIERS SD05.TC R/TP SEMTECH SOD323 5V D147 0DR050008AA O DIODE,RECTIFIERS SD05.TC R/TP SEMTECH SOD323 5V D148 0DR050008AA O DIODE,RECTIFIERS SD05.
S AL LOCA.NO PART NO(LG) A DESCRIPTION SPECIFICATION IC146 0ICTMLG005A O IC,CUSTOMIZED LGDT3102 LG IC 80P HQFP TP AVS IC147 6200QL3001F O FILTER(CIRC),SAW X6931D EPCOS ST 44.
S AL LOCA.NO PART NO(LG) A DESCRIPTION SPECIFICATION F108 6200JB8009L O FILTER(CIRC),EMC EMC BMK800 50V 0.2A NIIGATA R/ F109 6200JB8009L O FILTER(CIRC),EMC EMC BMK800 50V 0.2A NIIGATA R/ F110 6200JB8009L O FILTER(CIRC),EMC EMC BMK800 50V 0.2A NIIGATA R/ F111 6200JB8009L O FILTER(CIRC),EMC EMC BMK800 50V 0.2A NIIGATA R/ F112 6200JB8009L O FILTER(CIRC),EMC EMC BMK800 50V 0.2A NIIGATA R/ F113 6200JB8009L O FILTER(CIRC),EMC EMC BMK800 50V 0.
S AL LOCA.NO PART NO(LG) A DESCRIPTION SPECIFICATION L801 0LA0102K018 O INDUCTOR AXIAL LEAD 10M K 2.3X3.4 L5 TP LED103 0DL211009AA O LED SML-211UT TP ROHM RED . LED104 0DL210008GA O LED SML-210MT R/TP ROHM GREEN 16 LED105 0DL210008GA O LED SML-210MT R/TP ROHM GREEN 16 TRANSFORMER T101 6170RNGW15A O TRANSFORMER,SMPS[COIL] SJE-W15A SOOJUNG PVR-STB TH01 6322B62204A O THERMISTOR,PTC NTPAN4R0LDRB0 MURATA 4.
S AL LOCA.NO PART NO(LG) A DESCRIPTION SPECIFICATION AR109 0RRZVTA001S O RESISTOR,DRAWING 3.3K OHM 1 / 16 W 3216 5% R/TP AR110 0RRZVTA001J O RESISTOR,DRAWING 4.7K OHM 1 / 16 W 3216 5% R/TP AR111 0RRZVTA001J O RESISTOR,DRAWING 4.7K OHM 1 / 16 W 3216 5% R/TP AR112 0RRZVTA001S O RESISTOR,DRAWING 3.3K OHM 1 / 16 W 3216 5% R/TP AR113 0RRZVTA001S O RESISTOR,DRAWING 3.3K OHM 1 / 16 W 3216 5% R/TP AR114 0RRZVTA001S O RESISTOR,DRAWING 3.
S AL LOCA.NO PART NO(LG) A DESCRIPTION SPECIFICATION R138 0RH3301C622 O RESISTOR,METAL GLAZED(CHIP) 3.3K OHM 1 / 16 W 1608 5.00% D R139 0RH3301C622 O RESISTOR,METAL GLAZED(CHIP) 3.3K OHM 1 / 16 W 1608 5.00% D R140 0RH4701C622 O RESISTOR,METAL GLAZED(CHIP) 4.7K OHM 1 / 16 W 1608 5.00% D R142 0RH2201C622 O RESISTOR,METAL GLAZED(CHIP) 2.2K OHM 1 / 16 W 1608 5.00% D R146 0RH2201C622 O RESISTOR,METAL GLAZED(CHIP) 2.2K OHM 1 / 16 W 1608 5.
S AL LOCA.NO PART NO(LG) A DESCRIPTION SPECIFICATION R227 0RH1002C622 O RESISTOR,METAL GLAZED(CHIP) 10K OHM 1 / 16 W 1608 5.00% D R231 0RH0000C622 O RESISTOR,METAL GLAZED(CHIP) 0 OHM 1 / 16 W 1608 5.00% D R234 0RH0000C622 O RESISTOR,METAL GLAZED(CHIP) 0 OHM 1 / 16 W 1608 5.00% D R236 0RH1001C622 O RESISTOR,METAL GLAZED(CHIP) 1K OHM 1 / 16 W 1608 5.00% D R237 0RH1001C622 O RESISTOR,METAL GLAZED(CHIP) 1K OHM 1 / 16 W 1608 5.
S AL LOCA.NO PART NO(LG) A DESCRIPTION SPECIFICATION R300 0RH5601C622 O RESISTOR,METAL GLAZED(CHIP) 5.6K OHM 1 / 16 W 1608 5.00% D R301 0RH2200C622 O RESISTOR,METAL GLAZED(CHIP) 220 OHM 1 / 16 W 1608 5.00% D R302 0RH3300C622 O RESISTOR,METAL GLAZED(CHIP) 330 OHM 1 / 16 W 1608 5.00% D R303 0RH1001C622 O RESISTOR,METAL GLAZED(CHIP) 1K OHM 1 / 16 W 1608 5.00% D R304 0RH1001C622 O RESISTOR,METAL GLAZED(CHIP) 1K OHM 1 / 16 W 1608 5.
S AL LOCA.NO PART NO(LG) A DESCRIPTION SPECIFICATION R387 0RH4700C622 O RESISTOR,METAL GLAZED(CHIP) 470 OHM 1 / 16 W 1608 5.00% D R388 0RH0752C622 O RESISTOR,METAL GLAZED(CHIP) 75 OHM 1 / 16 W 1608 5.00% D R390 0RH0222C622 O RESISTOR,METAL GLAZED(CHIP) 22 OHM 1 / 16 W 1608 5.00% D R391 0RH0000C622 O RESISTOR,METAL GLAZED(CHIP) 0 OHM 1 / 16 W 1608 5.00% D R395 0RH2201C622 O RESISTOR,METAL GLAZED(CHIP) 2.2K OHM 1 / 16 W 1608 5.
S AL LOCA.NO PART NO(LG) A DESCRIPTION SPECIFICATION R464 0RH4703C622 O RESISTOR,METAL GLAZED(CHIP) 470K OHM 1 / 16 W 1608 5.00% D R465 0RH1001C622 O RESISTOR,METAL GLAZED(CHIP) 1K OHM 1 / 16 W 1608 5.00% D R466 0RH1001C622 O RESISTOR,METAL GLAZED(CHIP) 1K OHM 1 / 16 W 1608 5.00% D R467 0RH0682C622 O RESISTOR,METAL GLAZED(CHIP) 68 OHM 1 / 16 W 1608 5.00% D R469 0RH1001C622 O RESISTOR,METAL GLAZED(CHIP) 1K OHM 1 / 16 W 1608 5.
S AL LOCA.NO PART NO(LG) A DESCRIPTION SPECIFICATION R724 0RH7500C622 O RESISTOR,METAL GLAZED(CHIP) 750 OHM 1 / 16 W 1608 5.00% D R725 0RH7500C622 O RESISTOR,METAL GLAZED(CHIP) 750 OHM 1 / 16 W 1608 5.00% D R728 0RH0332C622 O RESISTOR,METAL GLAZED(CHIP) 33 OHM 1 / 16 W 1608 5.00% D R729 0RH0332C622 O RESISTOR,METAL GLAZED(CHIP) 33 OHM 1 / 16 W 1608 5.00% D R730 0RH0332C622 O RESISTOR,METAL GLAZED(CHIP) 33 OHM 1 / 16 W 1608 5.
S AL LOCA.
