Water Dispenser User Manual

ManualsBrandsZenith ManualsWater DispenserHYDROTAP 36651

Domestic models

37671 Zenith HydroTap BC60/85

37601 Zenith HydroTap BF60 (Ambient)

37691 Zenith HydroTap B60

37676 Zenith HydroTap BCD60/85

37606 Zenith HydroTap BFD60 (Ambient)

37696 Zenith HydroTap BD60

30009 Zenith HydroTap HT60

30609 Zenith HydroTap HTD60

36051 Zenith HydroTap HT60/85

36651 Zenith HydroTap HTD60/85

Zenith HydroTap

Filtered boiling and chilled drinking water for kitchens and tea rooms.

Commercial Models

30281 Zenith HydroTap BC150/175

30271 Zenith HydroTap BC100/125

37201 Zenith HydroTap B10OF

38201 Zenith HydroTap B150F

37291 Zenith HydroTap B100

38291 Zenith HydroTap B150

Disabled Models

37276 Zenith HydroTap BCD100/125

38286 Zenith HydroTap BCD150/175

37206 Zenith HydroTap BD10OF

38206 Zenith HydroTap BD150F

37296 Zenith HydroTap BD100

38296 Zenith HydroTap BD150

Installation and Operating Instructions

81467 - February 2005

Summary of content (20 pages)

PAGE 1
Installation and Operating Instructions Zenith HydroTap ® Filtered boiling and chilled drinking water for kitchens and tea rooms.
PAGE 2
Contents Read These Warnings First . . . . . . . . . . . . . . . . . . . . . . . . . .3 Models covered by these instructions . . . . . . . . . . . . . . . . . .4 Installation Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Special tools required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Installation procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Step A - Installing the tap (all models) . . . . . . . . . . . .
PAGE 3
Read These Warnings First Safety Do not allow young children, handicapped or infirm persons, to use the Zenith HydroTap without supervision. Refrigerant The Zenith HydroTap Chilling unit contains 134A refrigerant under pressure. No part of the unit should be exposed to a naked flame. Maintenance of the refrigeration unit must be carried out by an accredited service provider or qualified refrigeration mechanic.
PAGE 4
# Section Heading Read These Warnings First continued Frost Protection If this appliance is located where the ambient air temperature could fall below 5ºC when the heater is not in use, do not turn off the appliance electrically. This safeguard does not offer the same protection to the connecting pipework and fittings. Installation Environment Considerations This unit is intended for indoor use only and should never be installed outdoors or exposed to the elements of nature.
PAGE 5
Installation Requirements continued • This switch must provide all-pole disconnection and a contact separation of at least 3mm installed in accordance with wiring rules. • Cold water supply with a minimum working pressure of 175 kPa and a maximum working pressure of 700 kPa connected via an isolation valve. If pressure is likely to exceed 700 kPa, install a 500 kPa Pressure Limiting Valve.
PAGE 6
Installation procedure continued Step B - Installing the undersink unit (all models) SPECIAL NOTE: The HydroTap undersink units are heavy, take note of the weights listed in the table on page 4. If you think you cannot lift the unit safely, get help and avoid possible injury. Before positioning the heater connect the braided water inlet hose (supplied) to the cold water inlet on the unit. This is located at the rear of the unit.
PAGE 7
Installation procedure continued Step D - Connecting the water supply (all models) To prevent sediment from entering the Zenith HydroTap at connection, flush water through the supply line thoroughly before connection to the Zenith HydroTap. Open the access door and check that the filter is in place and secure. Connect the water supply to the undersink unit using the attached flexible hose. Turn on water and check for leaks. If no leaks are evident turn the poer on.
PAGE 8
Font installation procedure 1. Position the Font template (provided) on the bench area. Ensure the position you select is within the length of the supply tube and USB cable fixed to the Tap Head Assembly. These cannot be extended. 2. Check again for correct positioning. The supply hoses must have constant fall back to the tank assembly. Cut the holes as shown on the template. 3.
PAGE 9
Operating the Tap Blue Chilled Water Light On all the time: This indicates that the chilled water temperature is within the usable range. Flashing slowly : This indicates that the chilled water is not at the right temperature. Wait up to 20 minutes.When the chilled water is ready, the light will stop flashing. Note: The Zenith HydroTap is designed to dispense chilled water in the temperature range 5°C to 10°C. During heavy usage, the temperature can rise out of this range.
PAGE 10
Cleaning Do not use strong, corrosive, spray or abrasive cleaners. Clean with a soft cloth or brush and mild soap and water. Do not spray water over the tap as it may damage the low-voltage electronics. Undersink units must never be cleaned with water jets. Replacing the Filter (filtered models only) The Zenith HydroTap notifies the user when filter replacement is due. The default seting is 6000L. When a filter change is due, the Change Filter light flashes once a minute and remains so until reset.
PAGE 11
Setting the Energy Saver Timer (products with this feature only) Plus Adjust Button Mode Plus Button Minus Adjust Button Mode Minus Button Normal Operation (not available on HT boiling only series) Set Time To change time, press either Mode ∧ or Mode ∨ button until Set Time is on the display screen. Press ∧ Adjust button to increase time or ∨ Adjust button to decrease time. Time increases or decreases in increments of one minute. Hold the Adjust buttons down for rapid increases or decreases.
PAGE 12
Auxiliary Fan Attachment Auxiliary fan connection Cold water connection Electrical connections (excluding HT boiling only models) The HydroTap is equipped with an auxiliary connection point for an exhaust fan on the rear panel close to the cold water inlet / flex and plug area. The fan kit is available as a spare part. The fan operates in parallel with the Condensor fan helping to remove heat from the cupboard space.
PAGE 13
Trouble Shooting Symptom Possible Cause Solution No LED display, no tap head lights or, no water when tap levers are operated. No power. Check power supply. Plug is not located in power socket. Ensure power plug is correctly fitted and switch is turned ON. Tap loom is not connected to HydroTap unit. Check loom connection. Possible internal fault. Contact local Zenith service provider. Program in OFF cycle Check LCD for information. Water supply isolated. Check water supply is on.
PAGE 14
Exploded View Chiller Module and Spare Parts Item Kit No. Description Item Kit No.
PAGE 15
Exploded View Boiler Module and Spare Parts Item Kit No. Description Item Kit No.
PAGE 16
Exploded View HT Series Boiling Only and Spare Parts ITEM KIT NO.
PAGE 17
Notes Zenith Hydro Tap Installation and Operating Instructions - 81467 - February 2005 Page 17 of 20
PAGE 18
Notes Page 18 of 20 Zenith Hydro Tap Installation and Operating Instructions - 81467 - February 2005
PAGE 19
Notes Zenith Hydro Tap Installation and Operating Instructions - 81467 - February 2005 Page 19 of 20
PAGE 20
# Warranty Information The Zenith appliance you have chosen is precision-built from the finest materials available and should give many years of trouble free service. Certain warranties may be implied by law into your contract with Zenith. The warranty provided below is additional to these implied warranties and nothing set out below shall limit your statutory rights or rights at law.