SERVICE MANUAL Model Series: P60W26 Product Type: Chassis: Manual Series: Manual Part #: Model Line: Product Year: Plasma HDTV NP-00KA/B PV154 923-03493 E 2002 CONTENTS Safety .......................................................... 2 Servicing/Troublshooting ............................... 4 Model Part Lists .......................................... 12 Exploded Views ........................................... 13 Schematics .................................................
PRODUCT SAFETY IMPORTANT SAFETY NOTICE TIPS ON PROPER INSTALLATION This manual was prepared for use only by properly trained audio-visual service technicians. 1. Never install any receiver in a closed-in recess, cubbyhole, or closely fitting shelf space over, or close to, a heat duct, or in the path of heated air flow. 2. Avoid conditions of high humidity such as: outdoor patio installations where dew is a factor, near steam radiators where steam leakage is a factor, etc. 3.
TABLE OF CONTENTS IMPORTANT SAFETY NOTICE .................................. 2 TABLE OF CONTENTS ............................................ 3 GENERAL INFO ................................................... 5 FEATURES ..................................................... 5 SPECIFICATIONS ............................................. 5 FRONT .......................................................... 7 BACK ........................................................... 7 REMOTE CONTROL ........................
-4-
GENERAL INFO GENERAL INFO SPEAKER STAND H x W x D ............................... 8.70" x 8.60" x 8.70" Weight ........................................................ 4 lbs. UPC Code ...................................... 04464200552 8 FEATURES 60" PLASMA HDTV MONITOR Groundbreaking display technology delivers superior image clarity, color, and brightness in large-format televisions that are less than 4" thick ACCESSORIES 15-Wire RGB Cable .............................................
GENERAL INFO Color Gradation Filter ......................................... Yes Input Signal ............ NTSC, HD, VGA, SVGA, XGA, SXGA Display modes ........................... Normal, Wide, Zoom Side Panels (Gray Bars for 4:3 Display) .................. Yes AUDIO Mono/Stereo/MTS/SAP ......................... Mono/Stereo Bass/Treble/Balance ........................................... Yes Total Audio (Watts) .......................... 20W (2 x 10W) Speaker Size (Dimensions) .......
GENERAL INFO FRONT Input Select Sub Power INPUT VOLUME SELECT ON/OFF Remote Control Sensor Main power button Volume BACK S-Video Y Y PV154 - 923-03493 PB PR PB PR ½ (+) Audio Inputs 7 ( ) ( ) AC INPUT (+) S-Video (+) ( ) ( ) (+) P60W26 - SERVICING
GENERAL INFO REMOTE CONTROL POWER ON POWER ON Toggles the on on and off. SYSTEM OFF SLEEP MUTE * MUTE Toggles the sound on and off. 1 3 2 VIDEO PC Toggles through available video inputs. Composite, Component, RGB-PC, & RGB-DTV 4 5 7 8 VIDEO/PC THUMBSTICK Navigates the on-screen menus and adjusts system settings and preferences. Use the arrows to navigate menus and press the center to select. INPUT SELECT Auto Picture Control Turns sound Off and On while picture remains.
GENERAL INFO INSTALLATION It is recommended that this product only be used at an altitude of less than 6562 feet (2000m) to get the best quality picture and sound. This plasma display is designed to be mounted horizontally (wide viewing). - Your P42W22, P42W22B models (Monitor) can be installed on a wall or on a desktop pedestal. Wall mount and stands are optional and not supplied with the monitor. (For further information, refer to the optional Tilt/Wall Mounting Bracket Installation and Setup Guide.
USER MENUS USER MENUS APC (AUTO PICTURE CONTROL) APC is used to set the Monitor for the best picture appearance. Press the apc button. Use the APC or volume buttons to select the picture appearance setup. APC is not available in RGB or PIP mode. Each press of vol buttons selects the menu option. Available options are select CLEAR, SOFT or USER. User refers to manual adjustments made to the picture menu options. SPECIAL LANGUAGE ARC SCREEN TRANSPARENCY PIP SET ID COLOR TEMP.
USER MENUS Tips • If a still picture is on the screen for more than 5 minutes, the image becomes dark. This is a protective feature designed to lessen the chance of a ghost image burning onto the monitor screen. If another function is activated, normal screen brightness is restored. This feature isn’t available for RGB input source. SPECIAL LANGUAGE ARC SCREEN TRANSPARENCY PIP SET ID COLOR TEMP. SCREEN Use this option to correct trembling or instability of a videotape image.
USER MENUS PICTURE FORMAT Use the ratio button to select the desired picture format. Each time you press ratio or volume buttons, you cycle through 16:9, 4:3, and ZOOM. With RGB-PC as the source, you can select either 16:9 or 4:3 screen aspect ratios. With the RGB-DTV source, you can select the 16:9 screen aspect ratio. If 4:3 mode is used for a long time, the outline of the image may remain on the screen after you change to the 16:9 screen aspect ratio.
SERVICING ADJUSTMENT INSTRUCTIONS These instructions are applied to all of the PDP monitor, NP-00KB. Because this is not a hot chassis, it is not necessary to use an isolation transformer. However, the use of isolation transformer will help protect test instruments. Adjustment must be done in the correct order. If there is no specific designation, the adjustment must be performed at 25±5oC of temperature and 65±10% of relative humidity.
SERVICING (3) To adjust Low Light, place the sensor to the ninth pattern (Dark). Then select the W/B by pressing the ADJ button on the remote or adjustment and press the VOL + button to enter Adjustment Mode. Select the G cut and B cut, press the VOL +/- Key and adjust it until color coordination becomes (R cut fixation): color coordination : X=0.283±0.005, Y=0.295±0.
SERVICING SERVICE MENU Service Menu Adjustments for Plasma Display Once the Main Video Scan Converter module is installed, the unit will power on as soon as A/C is applied. The EEPROM data will be set to Factory default values. The following charts and instructions will allow you to set access the service menu and make any necessary adjustments during the repair and installation of the PDP.
SERVICING No Video Nothing output of image. Check Input of AC. (85~225V) Abnormal Connect plug with the set. Normal Check ST-BY LED ON Main S/W ON. Abnormal Check AC Line Fuse. Normal Check LED YELLOW Sub S/W ON. Abnormal Check OPEN with PFC R8301, R8302, R8303. Abnormal Replace R8301, R8302, R8303. Normal Abnormal Check OPEN with R8538, R8539, 8540. Normal Check normal operation with VS, VA PACK. Check operation of FAN. Check output of 5V MONI, 5V CTL. Normal Check CRTL Pack VS On.
SERVICING Abnormal Picture Abnormal Picture Abnormal Check JAGASM IC501 Input PC signal. Normal Check CXA2101 IC203 Check SII150 IC901 Normal Check ADV7123 IC406 Check cable of pin 21 P901 Normal Check FLI2220 IC404 Normal Check FLI2200 IC403 Normal Check VPC3230 IC201 Normal Check Input jack & Connector. No Sound Check connector speaker to set. PV154 - 923-03493 Check MSP3401 IC601 17 Check LA4282 IC603 Check Input Jack.
PARTS MODEL PARTS All FC models are module level repair only. Parts contact information is below. Voice: 1-888-3-ZENITH Fax: 1-888-6-ZENITH Mail: Zenith National Parts 201 James Record Road Huntsville, AL 35824-1513 580 590 600 610 620 630 6871VSMB46A 6871VSM668A 6871VSM669A 6871VSM670A 6871VSM676B 6871VSMC90A 640 6871VSMB57A PCB ASSEMBLY,SUB VER.
DIAGRAMS DIAGRAMS EXPLODED VIEW 300 305 301 302 306 303 101 304 640 201 331 620 202 212 560 203 211 550 310 213 330 204 210 206 209 205 214 208 200 207 600 590 540 610 530 520 580 630 401 400 PV154 - 923-03493 19 P60W26 - DIAGRAMS
~ PV154 - 923-03493 POWER CONTROL 20 PFC 380V Power Switching FET PFC INDUCTOR UC 3854 HIGH POWER FACTOR PREREGULATOR PFC Pack Aux.
PV154 - 923-03493 Control (RS232C) YCbCr/ YPbPr CVBS Y/C 21 L R AUDIO AMP LA4282 (L & R) AUDIO AUDIO SWITCH (LA7222) COLOR DECODER (VPC3230D) 5 YUV 16 4 H/V/ FIELD/ LLC1 2 H MEMORY (4M-BYTE) DEINTERLACE (FLI2200) Rx,Tx RGBHV H/V RGB 2 30 16 YUV 30 ROM (AT29C010) (74HCT373) RGBHV DAC (ADV7123) 5 RGB Y,Pb,Pr(MNT) 3 ENHANCER (FLI2220) 5 H/V/CLK/ HBLK/VBLK RGB 3 SCALER (JAGASM) MEMORY (8M-BYTE) 48 MICOM 2 H/V Clamp V H 2 H/V TMDS TX (SII150) EEPROM X2416P PORT
2 1 3 4 5 6 7 8 9 G N/C GND 15V GND 5V N/C GND 15V GND 5V N/C GND 15V GND 5V P15 P1003B 5VA 5VA 5VA 5VA P1807 TP5 (GN) TP6 (VA) CN8 5V GND 15V GND N/C 5V GND 15V GND N/C N/C PFC+ PFC+ + CN2 TP2 (GND) N/C PFC+ PFC+ TP1 (380V) TP4 (VS) TP3 ( GN) P21 VS ADJ N/C 5V NOMI VSVA ON GND ST-BY5V P-CTL A/C ON CN3 + A-B+ Not Used A-GND P6 VSVA ON RUSH CTL. GND STB 5V P7 C FANGND FANVCC GND GND 12V 12V GND GND GND 5V 5V 5V 5V GND 15V GND N/C CN1 V SVA ON RUSH CTL.
Schematics SMPS Circuit 1 2 3 4 5 6 7 8 9 10 G F E D C B A PV154 - 923-03493 CRITICAL SAFETY COMPONENTS ARE IDENTIFIED BY THE SYMBOL REPLACE ONLY WITH PART NUMBERS SPECIFIED. . 23 NOTE: WAVEFORMS AND VOLTAGES WERE MEASURED AT 120VAC, CHANNEL 5, AND NSTC COLOR BARS.
Video/Scan Converter Circuit 1/3 1 2 3 4 5 6 7 8 G F E D C B A PV154 - 923-03493 CRITICAL SAFETY COMPONENTS ARE IDENTIFIED BY THE SYMBOL REPLACE ONLY WITH PART NUMBERS SPECIFIED. . 24 NOTE: WAVEFORMS AND VOLTAGES WERE MEASURED AT 120VAC, CHANNEL 5, AND NSTC COLOR BARS.
Video/Scan Converter Circuit 2/3 1 2 3 4 5 6 7 8 9 10 G F E D C B A PV154 - 923-03493 CRITICAL SAFETY COMPONENTS ARE IDENTIFIED BY THE SYMBOL REPLACE ONLY WITH PART NUMBERS SPECIFIED. . 25 NOTE: WAVEFORMS AND VOLTAGES WERE MEASURED AT 120VAC, CHANNEL 5, AND NSTC COLOR BARS.
Video/Scan Converter Circuit 3/3 1 2 3 4 5 6 7 8 G F E D C B A PV154 - 923-03493 CRITICAL SAFETY COMPONENTS ARE IDENTIFIED BY THE SYMBOL REPLACE ONLY WITH PART NUMBERS SPECIFIED. . 26 NOTE: WAVEFORMS AND VOLTAGES WERE MEASURED AT 120VAC, CHANNEL 5, AND NSTC COLOR BARS.
Main & Power PCB Layout 2 1 3 4 5 6 7 8 9 10 G 0$,1 723 32:(5 723 F E D 32:(5 %27720 0$,1 %27720 C B A PV154 - 923-03493 CRITICAL SAFETY COMPONENTS ARE IDENTIFIED BY THE SYMBOL REPLACE ONLY WITH PART NUMBERS SPECIFIED. . 27 NOTE: WAVEFORMS AND VOLTAGES WERE MEASURED AT 120VAC, CHANNEL 5, AND NSTC COLOR BARS.
SMPS PCB Layout 1 2 3 4 5 6 7 8 G F 32:(5 0$,1 %27720 32:(5 0$,1 723 E D C B A PV154 - 923-03493 CRITICAL SAFETY COMPONENTS ARE IDENTIFIED BY THE SYMBOL REPLACE ONLY WITH PART NUMBERS SPECIFIED. . 28 NOTE: WAVEFORMS AND VOLTAGES WERE MEASURED AT 120VAC, CHANNEL 5, AND NSTC COLOR BARS.
Other PCB Layouts 1 G 2 3 &21752/ 723 4 5 6 7 8 32:(5 3)& 723 32:(5 9$ 723 32:(5 96 723 32:(5 3)& %27720 32:(5 9$ %27720 32:(5 96 %27720 9 10 &21752/ %27720 F $ 9 723 E 32:(5 6 : 723 32:(5 6 : %27720 $ 9 3$&. 723 D $ 9 %27720 $ 9 3$&. %27720 C B 32:(5 &21752/ 723 )$1 &21752/ 723 A 32:(5 &21752/ %27720 )$1 &21752/ %27720 PV154 - 923-03493 CRITICAL SAFETY COMPONENTS ARE IDENTIFIED BY THE SYMBOL REPLACE ONLY WITH PART NUMBERS SPECIFIED. .