BC2003 / TR2002 848J5J93A2 (801) G B OWNER’S MANUAL BRUSHCUTTERS BC2003 TR2002 GB-1
BC2003 / TR2002 EXPLANATION OF SYMBOLS AND SAFETY WARNINGS WARNING!!! RISK OF DAMAGING HEARING Wear head, eye and ear protection. MODEL SOUND LEVEL ISO 22868 ISO 10884 LpAav 3 21.7 cm 97 dB(A) LWA (guaranteed) 108 dB(A) VIBRATION LEVEL ISO 22867 ahv. eq 4.9 m/s 2 A(8) 3.
BC2003 / TR2002 G B Husqvarna Zenoah Co., Ltd. 80100001 and up 1st January 2008 Masahiko GOUDA SAFETY FIRST Instructions contained in warnings within this manual marked symbol concern critical points which must be taken with a into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions carefully and follow them without fail.
BC2003 / TR2002 1. Parts location (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) (12) (13) (14) 5 [BC2003] Primmer Air cleaner cover Choke lever Fuel tank Starter knob Line head Angle transmission Cutting attachment guard Handle Shaft tube Suspension point Throttle trigger Stop switch Throttle cable 3 14 2 1 13 3 11 14 12 2 1 9 13 4 11 12 9 10 10 7 8 6 7 8 6 2. Specification Overall size (L W H) ............................ 1795 x 230 x 303 / 1795 x 340 x 303 mm Dry weight .........
BC2003 / TR2002 3. Warning labels on the machine 15m (50ft) G B (1) (1) (2) (3) (4) (5) (6) (7) (2) (3) (4) (5) (6) (7) Read owner’s manual before operating this machine. Wear head, eye and ear protection. Wear foot protection. Wear gloves. Beware of thrown objects. Warning / Attention Keep all children, bystanders and helpers 15 meters away from the machine.
BC2003 / TR2002 5. For safe operation 1. Read this manual carefully until you completely understand and follow all safety and operating instructions. 2. Keep this manual handy so that you may refer to it later whenever any questions arise. Also note, if you have any questions which cannot be answered herein, contact the dealer from whom you purchased the product. 3. Always be sure to include this manual when selling, lending, or otherwise transferring the ownership of this product. 4.
BC2003 / TR2002 5. For safe operation BEFORE STARTING THE ENGINE 1. The area within a perimeter of 15 m of the person using the product should be considered a hazardous area into which no one should enter. If necessary, yellow warning rope, warning signs should be placed around the perimeter of the area.
BC2003 / TR2002 5. For safe operation • IF SOMEONE COMES 1. Guard against hazardous situations at all times. Warn adults to keep pets and children away from the area. Be careful if you are approached. Injury may result from flying debris. 2. If someone calls out or otherwise interrupts you while working, always be sure to turn off the engine before turning around. MAINTENANCE 1.
BC2003 / TR2002 6. Set up INSTALLING HANDLE HARNESS WARNING ALWAYS WEAR THE PROVIDED HARNESS WHEN USING THE MACHINE! • Install the handle to the shaft tube and clamp. INSTALLING CUTTING ATTACHMENT GUARD • Attach the guard to the bracket on the main pipe and fix it with 2 screws. Always make sure the machine is hooked securely to the harness. If you don't, you will be unable to control the machine safely. This can result in injury to yourself or others.
BC2003 / TR2002 7. Fuel ■ FUEL WARNING • Gasoline is very flammable. Avoid smoking or bringing any flame or sparks near fuel. Make sure to stop the engine and allow it cool before refueling the unit. Select outdoor bare ground for fueling and move at least 3 m (10 ft) away from the fueling point before starting the engine. • The Zenoah engines are lubricated by oil specially formulated for air-cooled 2-cycle gasoline engine use.
BC2003 / TR2002 8. Operation STARTING ENGINE WARNING WARNING The cutting head will start rotating upon the engine starts. 1. Feed fuel into the fuel tank and tighten the cap securely. The product is equipped with a centrifugal clutch mechanism, so the cutting attachment begins to rotate as soon as the engine is started by putting the throttle into the start position.
BC2003 / TR2002 8. Operation ADJUSTING THROTTLE CABLE • The normal play is 1 or 2 mm when measured at the carburetor side end. Readjust with the cable adjuster as required. TRIMMING GRASS AND WEEDS • Always remember that the TIP of the line does cutting. You will achieve better results by not crowding the line into the cutting area. Allow the unit to trim at its own pace. 1. Hold the unit so the head is off the ground and is tilted about 20 degrees toward the sweep direction.
BC2003 / TR2002 9.
BC2003 / TR2002 9. Maintenance SPARK PLUG • Starting failure and misfiring are often caused by a fouled spark plug. Clean the spark plug and check that the plug gap is in the correct range. For a replacement plug, use the correct type specified by ZENOAH. ANGLE TRANSMISSION • The reduction gears are lubricated by multipurpose, lithium-based grease in the angle transmission. Supply new grease every 25 hours of use or more often depending on the job condition.
BC2003 / TR2002 9. Maintenance PROCEDURES TO BE PERFORMED AFTER EVERY 100 HOURS OF USE 3. Take out the spool and pull off the old line. Put one end of new line through the spool holes and pull it until the length is equal between each part of the line. G B 1. Remove the muffler, insert a screwdriver into the vent, and wipe away any carbon buildup. Wipe away any carbon buildup on the muffler exhaust vent and cylinder exhaust port at the same time. 4.
BC2003 / TR2002 12. Troubleshooting guide Case 1. Starting failure CHECK fuel filter carburetor adjustment screw sparking (no spark) spark plug → → → → → PROBABLE CAUSES fuel filter is clogged out of normal range spark plug is fouled/wet plug gap is incorrect disconnected Case 2.
