BC2310DL 848J9893A1 (708) G B OWNER’S MANUAL BRUSHCUTTERS BC2310DL GB-1
BC2310DL EXPLANATION OF SYMBOLS AND SAFETY WARNINGS WARNING!!! RISK OF DAMAGING HEARING Wear head, eye and ear protection. MODEL EN27917 LpA BC2310DL 22.5 cm3 97.3 dB(A) SOUND LEVEL ISO 22868 : 2005 LwA guaranteed measured 110 dB(A) 107.9 dB(A) VIBRATION LEVEL ISO 22867 : 2004 idling racing 3.5 m/s2 5.
BC2310DL G B EC DECLARATION OF COMFORMITY We, ZENOAH CO., LTD.
BC2310DL 1. Parts location 5 (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) (12) (13) (14) Primer pump Air cleaner cover Choke lever Fuel tank Starter knob Line head Gear case Cutting attachment guard Loop handle Shaft tube Suspention point Throttle trigger Stop switch Throttle cable 3 14 13 12 9 10 8 6 2. Specification Overall size (L 3 W 3 H) ........................................................... 1765 x 330 x 310 mm Dry weight ..................................................................
BC2310DL 3. Warning labels on the machine 15m (50ft) G B (1) (1) (2) (3) (4) (5) (6) (7) (2) (3) (4) (5) (6) (7) Read owner’s manual before operating this machine. Wear head, eye and ear protection. Wear foot protection. Wear gloves. Beware of thrown objects. Warning / Attention Keep all children, bystanders and helpers 15 meters away from the machine.
BC2310DL 5. For safe operation 1. Read this manual carefully until you completely understand and follow all safety and operating instructions. 2. Keep this manual handy so that you may refer to it later whenever any questions arise. Also note, if you have any questions which cannot be answered herein, contact the dealer from whom you purchased the product. 3. Always be sure to include this manual when selling, lending, or otherwise transferring the ownership of this product. 4.
BC2310DL 5. For safe operation BEFORE STARTING THE ENGINE 1. The area within a perimeter of 15 m of the person using the product should be considered a hazardous area into which no one should enter. If necessary, yellow warning rope, warning signs should be placed around the perimeter of the area.
BC2310DL 5. For safe operation could result in serious burns or electrical shock. • IF SOMEONE COMES 1. Guard against hazardous situations at all times. Warn adults to keep pets and children away from the area. Be careful if you are approached. Injury may result from flying debris. 2. If someone calls out or otherwise interrupts you while working, always be sure to turn off the engine before turning around. MAINTENANCE 1.
BC2310DL 6. Set up INSTALLING HANDLE • Mount the handle to the shaft tube and clamp it at a location that is comfortable to you. G B (1) (1) About 28cm (11 inches) INSTALLING CUTTING ATTACHMENT GUARD • Attach the cutting attachiment guard with the bolts provided while inserting the spacer between the guard and the pipe. • Attach the guard skirt on the guard. INSTALLING CUTTING HEAD 1. Remove the plastic tube that is attached to the gear shaft. 2.
BC2310DL 7. Fuel ■ FUEL WARNING • Gasoline is very flammable. Avoid smoking or bringing any flame or sparks near fuel. Make sure to stop the engine and allow it cool before refueling the unit. Select outdoor bare ground for fueling and move at least 3 m (10 ft) away from the fueling point before starting the engine. • The Zenoah engines are lubricated by oil specially formulated for air-cooled 2-cycle gasoline engine use.
BC2310DL 8. Operation STARTING ENGINE WARNING WARNING The cutting head will start rotating upon the engine starts. 1. Feed fuel into the fuel tank and tighten the cap securely. The product is equipped with a centrifugal clutch mechanism, so the cutting attachment begins to rotate as soon as the engine is started by putting the throttle into the start position.
BC2310DL 8. Operation ADJUSTING THROTTLE CABLE • The normal play is 1 or 2 mm when measured at the carburetor side end. Readjust with the cable adjuster as required. TRIMMING GRASS AND WEEDS • Always remember that the TIP of the line does cutting. You will achieve better results by not crowding the line into the cutting area. Allow the unit to trim at its own pace. 1. Hold the unit so the head is off the ground and is tilted about 20 degrees toward the sweep direction. .
BC2310DL 9.
BC2310DL 9. Maintenance SPARK PLUG • Starting failure and misfiring are often caused by a fouled spark plug. Clean the spark plug and check that the plug gap is in the correct range. For a replacement plug, use the correct type specified by ZENOAH. GEAR CASE • The reduction gears are lubricated by multipurpose, lithium-based grease in the gear case. Supply new grease every 25 hours of use or more often depending on the job condition.
BC2310DL 9. Maintenance PROCEDURES TO BE PERFORMED AFTER EVERY 100 HOURS OF USE 4. Wind up the line in the correct direction as indicated on the spool. G B 1. Remove the muffler, insert a screwdriver into the vent, and wipe away any carbon buildup. Wipe away any carbon buildup on the muffler exhaust vent and cylinder exhaust port at the same time. 2. Tighten all screws, bolts, and fittings. 5.
BC2310DL 12. Troubleshooting guide Case 1. Starting failure CHECK fuel tank fuel filter carburetor adjustment screw sparking (no spark) spark plug → → → → → → PROBABLE CAUSES incorrect fuel fuel filter is clogged out of normal range spark plug is fouled/wet plug gap is incorrect disconnected Case 2.
