BCZ2610DL 848JPX93A0 (801) G B OWNER’S MANUAL BRUSHCUTTER BCZ2610DL GB-1
BCZ2610DL Husqvarna Zenoah Co., Ltd. BCZ2610DL 80100101 and up 1st January 2008 Masahiko GOUDA EXPLANATION OF SYMBOLS AND SAFETY WARNINGS WARNING!!! RISK OF DAMAGING HEARING Wear head, eye and ear protection. MODEL Blade 25.4 cm3 Line head 25.4 cm3 SOUND LEVEL ISO 22868 ISO 10884 LwA LpAav guaranteed 86 dB(A) 104 dB(A) 95 dB(A) 112 dB(A) VIBRATION LEVEL ISO 22867 ahv.eq 5.0 m/s2 3.3 m/s2 5.9 m/s2 3.
BCZ2610DL SAFETY FIRST Instructions contained in warnings within this manual marked with a symbol concern critical points which must be taken into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions carefully and follow them without fail. WARNINGS IN THE MANUAL WARNING This mark indicates instructions, which must be followed in order to prevent accidents, which could lead to serious bodily injury or death.
BCZ2610DL 2. Specification Overall size (L W H) ........................................................... 1830 x 400 x 365 mm Dry weight .......................................................................................................... 6.0 kg Engine Type ............................................................................ Air-cooled 2-stroke gasoline Model ............................................................................................ Zenoah GZ25N Displacement ...........
BCZ2610DL 5. For safe operation 1. Read this manual carefully until you completely understand and follow all safety and operating instructions. 2. Keep this manual handy so that you may refer to it later whenever any questions arise. Also note, if you have any questions which cannot be answered herein, contact the dealer from whom you purchased the product. 3. Always be sure to include this manual when selling, lending, or otherwise transferring the ownership of this product. 4.
BCZ2610DL 5. For safe operation BEFORE STARTING THE ENGINE 1. The area within a perimeter of 15 m of the person using the product should be considered a hazardous area into which no one should enter. If necessary, yellow warning rope, warning signs should be placed around the perimeter of the area.
BCZ2610DL 5. For safe operation • IF SOMEONE COMES 1. Guard against hazardous situations at all times. Warn adults to keep pets and children away from the area. Be careful if you are approached. Injury may result from flying debris. 2. If someone calls out or otherwise interrupts you while working, always be sure to turn off the engine before turning around. MAINTENANCE 1.
BCZ2610DL 6. Set up SUSPENSION POINT NOTE Be the SUSPENSION POINT in the location of the arrow mark. SUSPENSION POINT arrow mark INSTALLING HANDLE NOTE The handle is put during the arrow mark. • Mount the handle to the shaft tube and suspension point it at a location that is comfortable to you. G N MI ACIN P S About 48 cm INSTALLING CUTTING ATTACHMENT GUARD FOR LINE HEAD • Attach the cutting attachment guard with the bolts provided while inserting the spacer between the guard and the pipe.
BCZ2610DL 7. Fuel ■ FUEL WARNING • Gasoline is very flammable. Avoid smoking or bringing any flame or sparks near fuel. Make sure to stop the engine and allow it cool before refueling the unit. Select outdoor bare ground for fueling and move at least 3 m (10 ft) away from the fueling point before starting the engine. • The Zenoah engines are lubricated by oil specially formulated for air-cooled 2-cycle gasoline engine use.
BCZ2610DL 8. Operation WARNING STARTING ENGINE WARNING The cutting head will start rotating upon the engine starts. 1. Feed fuel into the fuel tank and tighten the cap securely. The product is equipped with a centrifugal clutch mechanism, so the cutting attachment begins to rotate as soon as the engine is started by putting the throttle into the start position.
BCZ2610DL 8. Operation ADJUSTING THROTTLE CABLE • The normal play is 1 or 2 mm when measured at the carburetor side end. Readjust with the cable adjuster as required. METAL BLADE USAGE 1. Check the bolt to fasten the blade and be sure the bolt has no fault, and no abrasion. 2. Be sure that the blade and the holder have been fastened according to instruction and the blade turns smoothly without abnormal noise.
BCZ2610DL 8. Operation CUTTING METHOD (a) Use the front left side cutting. (b) Guide the blade from your right to left with it tilted slightly to your left. (c) When mowing a wide area, start working from your left end to avoid interference of cut grass. (d) The blade may be seized by weeds if the engine speed is too low, or the blade cuts too deep into weeds. Adjust the engine speed and cutting depth according to the condition of object.
BCZ2610DL 9.
BCZ2610DL 9. Maintenance IMPORTANT • Note that using any spark plug other than those designated may result in the engine failing to operate properly or in the engine becoming overheated and damaged. • To install the spark plug, first turn the plug until it is finger tight, then tighten it a quarter turn more with a socket wrench. TIGHTENING TORQUE: 9.8 ~ 11.8 N.m. (1 ~ 1.2 kgm) MUFFLER WARNING AIR FILTER • The air filter, if clogged, will reduce the engine performance.
BCZ2610DL 9. Maintenance 10. Storage • When checking the machine to make sure that it is okay before using it, check the area around the muffler and remove any wood chips or leaves w h i ch h av e a t t a ch e d t h e m s e l v e s t o t h e brushcutter. Failing to do so could cause the muffler to become overheated and that in turn could cause the engine to catch on fire. Always make sure that the muffler is clean and free of wood chips, leaves, and other waste before use.
BCZ2610DL 12. Troubleshooting guide Case 1. Starting failure CHECK fuel tank fuel filter carburetor adjustment screw sparking (no spark) spark plug → → → → → → PROBABLE CAUSES incorrect fuel fuel filter is clogged out of normal range spark plug is fouled/wet plug gap is incorrect disconnected Case 2.
