BCZ2610DL 115 34 07-10 (001) G B OWNER’S MANUAL BRUSHCUTTER BCZ2610DL Original Language GB-1
BCZ2610DL EC DECLARATION OF CONFORMITY (Applies to Europe only) The undersigned manufacturer, Husqvarna Zenoah Co.,Ltd., 1-9, Minamidai, Kawagoe, Saitama, Japan, declares under sole responsibility that the following products referred to in this declaration conform with the requirement of the following COUNCIL’S DIRECTIVE. The products referred to are : DESIGNATION MANUFACTURER MODELS SERIAL NUMBERS DATING : Brushcutter : Husqvarna Zenoah Co., Ltd.
BCZ2610DL SAFETY FIRST Instructions contained in warnings within this manual marked with a symbol concern critical points which must be taken into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions carefully and follow them without fail. WARNINGS IN THE MANUAL WARNING This mark indicates instructions, which must be followed in order to prevent accidents, which could lead to serious bodily injury or death.
BCZ2610DL 2. Specification Overall size (L W H) ........................................................... 1830 x 400 x 365 mm Dry weight .......................................................................................................... 5.8 kg Engine Type ............................................................................ Air-cooled 2-stroke gasoline Model ............................................................................................ Zenoah GZ25N Displacement ...........
BCZ2610DL 5. For safe operation 1. Read this manual carefully until you completely understand and follow all safety and operating instructions. 2. Keep this manual handy so that you may refer to it later whenever any questions arise. Also note, if you have any questions which cannot be answered herein, contact the dealer from whom you purchased the product. 3. Always be sure to include this manual when selling, lending, or otherwise transferring the ownership of this product. 4.
BCZ2610DL 5. For safe operation BEFORE STARTING THE ENGINE 1. The area within a perimeter of 15 m of the person using the product should be considered a hazardous area into which no one should enter. If necessary, yellow warning rope, warning signs should be placed around the perimeter of the area.
BCZ2610DL 5. For safe operation • IF SOMEONE COMES 1. Guard against hazardous situations at all times. Warn adults to keep pets and children away from the area. Be careful if you are approached. Injury may result from flying debris. 2. If someone calls out or otherwise interrupts you while working, always be sure to turn off the engine before turning around. MAINTENANCE 1.
BCZ2610DL 6. Set up A Package contains the items as illustrated. 1 3 2 4 7 5 6 14 12 9 8 16 11 15 13 10 (1) (2) (3) (4) (5) (6) (7) (8) GB-8 Unit Harness Handle Screw Cutting attachment guard Gurad skirt Spacer Trimmer head (9) (10) (11) (12) (13) (14) (15) (16) Blade Cover Blade cover Hexagon socket (S16/S17) with torx driver (T-27) Spanner (S8/S10) Bar (Ф4.
BCZ2610DL 6. Set up SUSPENSION POINT NOTE Be the SUSPENSION POINT in the location of the arrow mark. SUSPENSION POINT arrow mark INSTALLING HANDLE NOTE The handle is put during the arrow mark. • Mount the handle to the shaft tube and suspension point it at a location that is comfortable to you. MIN CING SPA About 48 cm HARNESS WARNING ALWAYS WEAR THE PROVIDED HARNESS WHEN USING THE MACHINE! Always make sure the machine is hooked securely to the harness.
BCZ2610DL 7. Fuel ■ FUEL WARNING • Gasoline is very flammable. Avoid smoking or bringing any flame or sparks near fuel. Make sure to stop the engine and allow it cool before refueling the unit. Select outdoor bare ground for fueling and move at least 3 m (10 ft) away from the fueling point before starting the engine. • The Zenoah engines are lubricated by oil specially formulated for air-cooled 2-cycle gasoline engine use.
BCZ2610DL 8. Operation WARNING STARTING ENGINE WARNING The cutting head will start rotating upon the engine starts. 1. Feed fuel into the fuel tank and tighten the cap securely. The product is equipped with a centrifugal clutch mechanism, so the cutting attachment begins to rotate as soon as the engine is started by putting the throttle trigger into the start position.
BCZ2610DL 8. Operation ADJUSTING THROTTLE CABLE • The normal play is 1 or 2 mm when measured at the carburetor side end. Readjust with the cable adjuster as required and tighten the screw up. (3) (2) (1) METAL BLADE USAGE 1. Check the bolt to fasten the blade and be sure the bolt has no fault, and no abrasion. 2. Be sure that the blade and the holder have been fastened according to instruction and the blade turns smoothly without abnormal noise. (1) Cable adjuster (2) 0.
BCZ2610DL 8. Operation CUTTING METHOD (a) Use the front left side cutting. (b) Guide the blade from your right to left with it tilted slightly to your left. (c) When mowing a wide area, start working from your left end to avoid interference of cut grass. (d) The blade may be seized by weeds if the engine speed is too low, or the blade cuts too deep into weeds. Adjust the engine speed and cutting depth according to the condition of object.
BCZ2610DL 9.
BCZ2610DL 9. Maintenance IMPORTANT • Note that using any spark plug other than those designated may result in the engine failing to operate properly or in the engine becoming overheated and damaged. • To install the spark plug, first turn the plug until it is finger tight, then tighten it a quarter turn more with a socket wrench. TIGHTENING TORQUE: 9.8 ~ 11.8 N.m. (1 ~ 1.2 kgm) MUFFLER WARNING AIR FILTER • The air filter, if clogged, will reduce the engine performance.
BCZ2610DL 9. Maintenance 10. Storage INTAKE AIR COOLING VENT Aged fuel is one of major causes of engine starting failure. Before storing the unit, empty the fuel tank and run the engine until it uses all the fuel left in the fuel line and the carburetor. Store the unit indoor taking necessary measures for rust prevention. WARNING • Check the intake air cooling vent after every 25 hours of use for blockage, and remove any waste which has attached itself to the brushcutter.
BCZ2610DL 12. Troubleshooting guide Case 1. Starting failure CHECK fuel tank fuel filter carburetor adjustment screw sparking (no spark) spark plug → → → → → → PROBABLE CAUSES incorrect fuel fuel filter is clogged out of normal range spark plug is fouled/wet plug gap is incorrect disconnected Case 2.
