BCZ3200DL / BCZ3200DW 848JCG93A0 (511) G B OWNER’S MANUAL BRUSHCUTTERS BCZ3200DL BCZ3200DW GB-1
BCZ3200DL / BCZ3200DW DIRECTIVE 89/336/EEC, 98/37/EC BCZ3200DL BCZ3200DW 41200101 and up EXPLANATION OF SYMBOLS AND SAFETY WARNINGS WARNING!!! RISK OF DAMAGING HEARING IN NORMAL CONDITIONS OF USE, THIS MACHINE MAY INVOLVE A DAILY LEVEL OF PERSONAL EXPOSURE TO NOISE FOR THE OPERATOR EQUAL TO OR GREATER THAN 85 dB(A) MODEL EN27917 LpA BCZ3200DL 29.5 cm3 BCZ3200DW 29.5 cm3 98 dB(A) 97 dB(A) SOUND LEVEL ISO 10884 LwA guaranteed measured 110 dB(A) 84.3 dB(A) 111 dB(A) 86.
BCZ3200DL / BCZ3200DW SAFETY FIRST Contents Instructions contained in warnings within this manual marked symbol concern critical points which must be taken with a into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions carefully and follow them without fail. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12.
BCZ3200DL / BCZ3200DW 2. Specification BCZ3200DL / BCZ3200DW Overall size (L 3 W 3 H) ............................. 1860 x 395 x 325 / 1860 x 610 x 520 mm Dry weight .................................................................................................. 5.7 / 6.1 kg Engine Model ............................................................................................ Zenoah GZ30N Displacement ........................................................................................... 29.
BCZ3200DL / BCZ3200DW 5. For safe operation 1. Read this manual carefully until you completely understand and follow all safety and operating instructions. 2. Keep this manual handy so that you may refer to it later whenever any questions arise. Also note, if you have any questions which cannot be answered herein, contact the dealer from whom you purchased the product. 3. Always be sure to include this manual when selling, lending, or otherwise transferring the ownership of this product. 4.
BCZ3200DL / BCZ3200DW 5. For safe operation BEFORE STARTING THE ENGINE 1. The area within a perimeter of 15 m (50 ft) of the person using the product should be considered a hazardous area into which no one should enter. If necessary, yellow warning rope, warning signs should be placed around the perimeter of the area.
BCZ3200DL / BCZ3200DW 5. For safe operation eration or immediately after shutting down the engine. Doing so could result in serious burns or electrical shock. • IF SOMEONE COMES 1. Guard against hazardous situations at all times. Warn adults to keep pets and children away from the area. Be careful if you are approached. Injury may result from flying debris. 2. If someone calls out or otherwise interrupts you while working, always be sure to turn off the engine before turning around. MAINTENANCE 1.
BCZ3200DL / BCZ3200DW 6. Set up INSTALLING HANDLE (BCZ3200DL) • Mount the handle to the shaft tube and clamp it at a location that is comfortable to you. INSTALLING LINE HEAD 1. While locking the gear shaft by inserting the angled bar(1) into the holder(A)(2) on the angle transmission, loosen and remove the nut (left-handed). 2. Fit the line head assembly to the gear shaft. Tighten it securely by hand. INSTALLING HANDLE (BCZ3200DW) 1. Loosen the 4bolts on the upper cap and insert the handles equally.
BCZ3200DL / BCZ3200DW 7. Fuel ■ FUEL WARNING • Gasoline is very flammable. Avoid smoking or bringing any flame or sparks near fuel. Make sure to stop the engine and allow it cool before refueling the unit. Select outdoor bare ground for fueling and move at least 3 m (10 ft) away from the fueling point before starting the engine. • The Komatsu Zenoah engines are lubricated by oil specially formulated for air-cooled 2-cycle gasoline engine use.
BCZ3200DL / BCZ3200DW 8. Operation STARTING ENGINE WARNING WARNING The cutting head will start rotating upon the engine starts. 1. Feed fuel into the fuel tank and tighten the cap securely. 2. Rest the unit on a flat, firm place. Keep the cutting head off the ground and clear of surrounding objects, as it will start rotating upon starting of the engine. 3. Push the primer several times until overflown fuel flows out in the clear tube.
BCZ3200DL / BCZ3200DW 8. Operation ADJUSTING THROTTLE CABLE • The normal play is 1 or 2 mm when measured at the carburetor side end. Readjust with the cable adjuster as required. 1-2 mm (.04 in) METAL BLADE USAGE 1. Check the nut to fasten the blade and be sure the nut has no fault, and no abrasion. 2. Be sure that the blade and the holder have been fastened according to instruction and the blade turns smoothly without abnormal noise.
BCZ3200DL / BCZ3200DW 8. Operation CUTTING METHOD (a) Use the front left side cutting. (b) Guide the blade from your right to left with it tilted slightly to your left. (c) When mowing a wide area, start working from your left end to avoid interference of cut grass. (d) The blade may be seized by weeds if the engine speed is too low, or the blade cuts too deep into weeds. Adjust the engine speed and cutting depth according to the condition of object. c.
BCZ3200DL / BCZ3200DW 8. Operation 3. Use a slow, deliberate action to cut heavy growth. The rate of cutting motion will depend on the material being cut. Heavy growth will require slower action than will light growth. 4. Never swing the unit so hard as you are in danger of losing your balance or control of the unit. 5. Try to control the cutting motion with the hip rather than placing the full workload on the arm and hands.
BCZ3200DL / BCZ3200DW 9. Maintenance REFILLING TRIMMING LINE 1. For replacement line, use a diameter of 2.4mm(.095in). The spool is capable for a line upto 6m(20ft) on the 10cm(4”) head. Avoid using a larger line as it may cut down the trimming performance. WARNING • For safety reasons, do not use metalreinforced line. 2. Pinch the slotted area on the both sides of the spool housing to unhook the bottom cap. 3. Take out the spool and pull off the old line.
BCZ3200DL / BCZ3200DW 9. Maintenance MUFFLER that it is necessary to remove the engine cover shown in in order to be able to view the upper part of the cylinder. WARNING • Inspect periodically, the muffler for loose fasteners, any damage or corrosion. If any sign of exhaust leakage is found, stop using the machine and have it repaired immediately. • Note that failing to do so may result in the engine catching on fire.
BCZ3200DL / BCZ3200DW 12. Troubleshooting guide Case 1. Starting failure CHECK fuel tank fuel filter carburetor adjustment screw sparking (no spark) spark plug → → → → → → PROBABLE CAUSES incorrect fuel fuel filter is clogged out of normal range spark plug is fouled/wet plug gap is incorrect disconnected Case 2.
