HT2310 / CHT2310 848D0593A0 (706) G B OWNER’S MANUAL HEDGE TRIMMER HT2310 CHT2310 GB-1
HT2310 / CHT2310 EXPLANATION OF SYMBOLS AND SAFETY WARNINGS HT2310 WARNING!!! RISK OF DAMAGING HEARING Wear head, eye and ear protection. CHT2310 WARNING!!! RISK OF DAMAGING HEARING Wear head, eye and ear protection. MODEL HTZ2310 CHTZ2310 3 22.5 cm 22.5 cm3 SOUND LEVEL ISO 11094 prEN774 LwA(guaranteed) LpAav 108 dB(A) 106 dB(A) 97 dB(A) 95 dB(A) VIBRATION LEVEL ISO 8662 ahv,eq A(8) 2 9.8 m/s 12.
HT2310 / CHT2310 G B EC DECLARATION OF CONFORMITY We, ZENOAH CO., LTD. 1-9, Minamidai, Kawagoe, Saitama, Japan declare in sole responsibility that the following products referred to in this declaration conform with DIRECTIVE 89/336/EEC, 98/37/EC 2000/14/EC Internal control production.
HT2310 / CHT2310 1. Parts location 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. Right handle Fuel tank Starter Left handle Throttle lever Ignition switch Throttle Cable Muffler Blade Front handle Rear handle Plate receive 2. Specification Model ............................................................................................. HT2310 / CHT2310 Type ................................................................................................ double-action type HT2310 / CHT2310 .....................
HT2310 / CHT2310 3. Warning labels on the machine Read owner’s manual before operating this machine. Wear head, eye and ear protection. If warning label peels off or becomes soiled and impossible to read, you should contact the dealer from which you purchased the product to order new labels and affix them in the required location(s). Never modify your machine. We won’t warrant the machine, if you use the remodeled hedge trimmer or if you don’t observe the proper usage written in the manual.
HT2310 / CHT2310 5. For safe operation 1. THIS MACHINE CAN CAUSE SERIOUS INJURIES. Read this manual carefully until you completely understand and follow all safety and operating instructions. Also, know how to stop the machine quickly in an emergency. 2. Keep this manual handy so that you may refer to it later whenever any questions arise. Also note, if you have any questions which cannot be answered herein, contact the dealer from whom you purchased the product. 3.
HT2310 / CHT2310 5. For safe operation NOTE WARNING Check and follow the local regulations as to sound level and hours of operations for the product. Never place the throttle into the high-speed position when starting the engine. BEFORE STARTING THE ENGINE 1. The area within a perimeter of 15 m of the person using the product should be considered a hazardous area into which no one should enter. If necessary, yellow warning rope, warning signs should be placed around the perimeter of the area.
HT2310 / CHT2310 5. For safe operation 7. While operating the machine be always sure of a safe and secure operating position especially when using steps or a ladder. • IF SOMEONE COMES 1. Guard against hazardous situations at all times. Warn adults to keep pets and children away from the area. Be careful if you are approached. Injury may result from flying debris. 2. If someone calls out or otherwise interrupts you while working, always be sure to turn off the engine before turning around. MAINTENANCE 1.
HT2310 / CHT2310 6. Fuel ■ FUEL • Gasoline is very flammable. Avoid smoking or bringing any flame or sparks near fuel. Make sure to stop the engine and allow it cool before refueling the unit. Select outdoor bare ground for fueling and move at least 3 m (10 ft) away from the fueling point before starting the engine. agitate depending on oil ingredients, sufficient agitation is necessary for the engine to last long.
HT2310 / CHT2310 7. Operation STARTING ENGINE 5. Place the unit on a flat, firm place. Keep the cutting head clear of everything around it. WARNING The cutting head will start moving upon the engine starts. 6. While holding the unit firmly, pull out the starter rope quickly until engine fires. 1. Release the throttle lever and make sure it is fully back. 2. Set the ignition switch to the “I” position. b b a a [HT2310] (a) Throttle lever [CHT2310] (b) Ignition switch 3.
HT2310 / CHT2310 7. Operation ･ Use only as much throttle as is needed to do the job. CUTTING WORK Excessive engine speed is unnecessary. WARNING • Weather conditions and altitude may effect ･ Avoid cutting thick branches, for which will damage the blades and shorten the life of drive systems. carburation. • Do not allow anyone to stay close to the hedgetrimmer while working or while adjusting the carburetor.
HT2310 / CHT2310 8.
HT2310 / CHT2310 8. Maintenance AIR FILTER • The air filter, if clogged, will reduce the engine performance. Check and clean the filter element in warm, soapy water as required. Dry completely before installing. If the element is broken or shrunk, replace with a new one. SPARK PLUG • Starting failure and misfiring are often caused by a fouled spark plug. Clean the spark plug and check that the plug gap is in the correct range. For a replacement plug, use the correct type specified by ZENOAH. 0.6~0.
HT2310 / CHT2310 8. Maintenance PROCEDURES TO BE PERFORMED AFTER EVERY 100 HOURS OF USE 1. Remove the muffler, insert a screwdriver into the vent, and wipe away any carbon buildup. Wipe away any carbon buildup on the muffler exhaust vent and cylinder exhaust port at the same time. 2. Tighten all screws, bolts, and fittings. 3. Check to see if any oil or grease has worked its way in between the clutch lining and drum, and if it has, wipe it away using oil-free, lead-free gasoline. 9. Storage 1.
HT2310 / CHT2310 11. Troubleshooting guide Case 1. Starting failure CHECK fuel tank fuel filter carburetor adjustment screw sparking (no spark) spark plug Æ Æ Æ Æ Æ Æ PROBABLE CAUSES incorrect fuel fuel filter is clogged out of normal range spark plug is fouled/wet plug gap is incorrect disconnected Case 2.
