EBZ8001 115 40 01-73 (010) G B OWNER’S MANUAL BLOWER EBZ8001 GB-1
EBZ8001 SAFETY FIRST Instructions contained in warnings within this manual marked symbol concern critical points which must be taken with a into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions carefully and follow them without fail. WARNINGS IN THE MANUAL WARNING This mark indicates instructions, which must be followed in order to prevent accidents, which could lead to serious bodily injury or death.
EBZ8001 2. Specification Model Dimensions (LxWxH)** Dry weight* Fuel tank capacity Engine type Displacement Air filter Carburetor Ignition system Spark plug Muffler Operating engine speed Fuel consumption Air volume* Max. Air volume** Max. Air velocity* mm kg liter 3 cm rpm liter/h cu.m/min. cu.m/min. m/sec. EBZ8001 380 x 490 x 496 12.6 2.3 Air cooled 2-cycle gasoline engine 71.9 2-stage fresh flow filter system Rotary Digital Ignition NGK CMR7H (Noise-proof) Spark arrester equipped 2000 to 6700 1.
EBZ8001 5. For safe operation WARNING 1. Read this manual carefully until you completely understand and follow all safety and operating instructions. 2. Keep this manual handy so that you may refer to it later whenever any questions arise. Also note, if you have any questions which cannot be answered herein, contact the dealer from whom you purchased the product. 3. Always be sure to include this manual when selling, lending, or otherwise transferring the ownership of this product. 4.
EBZ8001 5. For safe operation 8. The ignition system of your unit produces an electromagnetic field of a very low intensity. This field may interfere with some pacemakers. To reduce the risk of serious or fatal injury, persons with pacemaker should consult their physician and the pacemaker manufacturer before operating this tool. WORKING CIRCUMSTANCE 1. To reduce the risk of injury associated with exhaust fume inhalation, do not operate in unventilated area.
EBZ8001 5. For safe operation WARNING • Check to see if the shock-absorbing rubber mount has become cracked or otherwise damaged. Note that failing to replace this rubber mount when it has become cracked or damaged may cause the engine to come loose from its frame during use, thus resulting in possible serious bodily injury. • If cracked, be sure to replace without delay.
EBZ8001 engine. Especially never forget to cool down the engine before refueling the machine. 10. In an emergency, pull up the lower portion of both strap buckles to loosen the straps. Move yourself away from the unit. 11. After using blowers and other equipment, CLEAN UP! Dispose of debris in trash receptacles. MAINTENANCE 1. In order to maintain your product in proper working order, perform the maintenance and checking operations described in the manual at regular intervals. 2.
EBZ8001 6. Set up FLEXIBLE HOSE and SWIVEL JOINT 1. Connect the blower and swivel joint with flexible hose. Clamp both ends of the flexible hose securely with the hardware supplied with the unit. (2) (3) (1) (1) (2) (3) (4) WAIST BELT • The waist belt is attached to the rings on the left and right sides of the frame. Flexible hose Swivel joint Clamp (Large) Clamp (Small) (4) • Be sure to always tighten the buckle in front of your body.
EBZ8001 7. Fuel ■ FUEL • Gasoline is very flammable. Avoid smoking or bringing any flame or sparks near fuel. Make sure to stop the engine and allow it cool before refueling the unit. Select outdoor bare ground for fueling and move at least 3 m (10 ft) away from the fueling point before starting the engine. • The Zenoah engines are lubricated by oil specially formulated for air-cooled 2-cycle gasoline engine use.
EBZ8001 8. Operation STARTING ENGINE NOTE IMPORTANT When the engine fails to start after several attempts due to overchoking, open the choke and repeat pulling the rope. • Avoid operating the blower with the flexible tube and swivel joint disconnected. That will reduce the cooling air and the engine could be damaged by overheating. ADJUSTING IDLE SPEED • The idling speed is set for 2000 rpm at the factory.
EBZ8001 9. Maintenance Maintenance, replacement, or repair of the emission control device and systems may be performed by any non-road engine repair establishment or individual.
EBZ8001 9. Maintenance SPARK PLUG • The spark plug may gather carbon deposits on its firing end with reasonable use. Remove and inspect the spark plug every 25 hours and clean the electrodes as necessary with a wire brush. The spark gap should be adjusted to .025 in (0.6~0.7mm). (1) (2) (3) (4) • Plug manufacturers recommend replacing the plug twice a year to avoid unexpected plug failure in a job. REPLACEMENT PLUG IS NGK CMR7H.
EBZ8001 9. Maintenance AIR INLET NET IMPORTANT • Blowing air is taken in from the air inlet net. When air flow has dropped down during operation, stop the engine and inspect the air inlet net for blocking by obstacles. • Note that failure to remove any such obstacles may result in the engine becoming overheated and damaged. HARNESS • If the harness is damaged it may break during use, thus causing the product to fall and resulting in personal injury.
EBZ8001 12. Troubleshooting guide Case 1. Starting failure CHECK fuel tank fuel filter carburetor adjustment screw sparking (no spark) spark plug → → → → → → PROBABLE CAUSES incorrect fuel fuel filter is clogged out of normal range spark plug is fouled/wet plug gap is incorrect disconnected Case 2.
