EBZ8001 115335710 (001) Original Instruction G B OWNER’S MANUAL BLOWER EBZ8001 GB-1
EBZ8001 EC DECLARATION OF CONFORMITY (Applies to Europe only) The undersigned manufacturer, Husqvarna Zenoah Co.,Ltd., 1-9, Minamidai, Kawagoe, Saitama, Japan, declares under sole responsibility that the following products referred to in this declaration conform with the requirement of the following COUNCIL’S DIRECTIVE. The products referred to are : DESIGNATION MANUFACTURER MODEL SERIAL NUMBERS DATING : BLOWER (Back-pack garden blower) : Husqvarna Zenoah Co., Ltd.
EBZ8001 SAFETY FIRST Instructions contained in warnings within this manual marked with a symbol concern critical points which must be taken into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions carefully and follow them without fail. WARNINGS IN THE MANUAL WARNING This mark indicates instructions, which must be followed in order to prevent accidents, which could lead to serious bodily injury or death.
EBZ8001 2. Specification Model Dimensions (LxWxH)** Dry weight* Fuel tank capacity Engine type Displacement Air filter Carburetor Ignition system Spark plug Muffler Operating engine speed Fuel consumption Air volume* Max. Air volume** Max. Air velocity* mm kg liter cm3 rpm liter/h cu.m/min. cu.m/min. m/sec. EBZ8001 380 x 490 x 496 12.6 2.3 Air cooled 2-cycle gasoline engine 71.9 2-stage fresh flow filter system Rotary Digital Ignition NGK CMR7H (Noise-proof) Spark arrester equipped 2000 to 6700 1.9 19.
EBZ8001 5. For safe operation 1. Read this manual carefully until you completely understand and follow all safety and operating instructions. 2. Keep this manual handy so that you may refer to it later whenever any questions arise. Also note, if you have any questions which cannot be answered herein, contact the dealer from whom you purchased the product. 3. Always be sure to include this manual when selling, lending, or otherwise transferring the ownership of this product. 4.
EBZ8001 5. For safe operation 1. Operate power equipment only at reasonable hours-not early in the morning or late at night when people might be disturbed. Comply with times listed in local ordinances. 2. To reduce sound levels, limit the number of pieces of equipment used at any one time. 3. Operate power blowers at the lowest possible throttle speed to do the job. 4. Check your equipment before operation, especially the muffler, air intakes and air filters.
EBZ8001 5. For safe operation f) Pay attention to the direction of the wind, do not work against the wind. g) Never point a blower tube toward an open flame to avoid the possibility of igniting the unit, causing injury to yourself or damage to surroundings. 3. To minimize blowing time. a) Use rakes and brooms to loosen debris before blowing. b) In dusty conditions, slightly dampen surfaces or use mister attachment when water is available.
EBZ8001 6. Set up FLEXIBLE HOSE and SWIVEL JOINT 1. Connect the blower and swivel joint with flexible hose. Clamp both ends of the flexible hose securely with the hardware supplied with the unit. (2) (3) (1) (1) (2) (3) (4) WAIST BELT • The waist belt is attached to the rings on the left and right sides of the frame. Flexible hose Swivel joint Clamp (Large) Clamp (Small) (4) • Be sure to always tighten the buckle in front of your body.
EBZ8001 7. Fuel ■ FUEL • Gasoline is very flammable. Avoid smoking or bringing any flame or sparks near fuel. Make sure to stop the engine and allow it cool before refueling the unit. Select outdoor bare ground for fueling and move at least 3 m (10 ft) away from the fueling point before starting the engine. • The Zenoah engines are lubricated by oil specially formulated for air-cooled 2-cycle gasoline engine use.
EBZ8001 8. Operation STARTING ENGINE NOTE IMPORTANT When the engine fails to start after several attempts due to overchoking, open the choke and repeat pulling the rope. • Avoid operating the blower with the flexible tube and swivel joint disconnected. That will reduce the cooling air and the engine could be damaged by overheating. ADJUSTING IDLE SPEED • The idling speed is set for 2000 rpm at the factory.
EBZ8001 9. Maintenance Maintenance, replacement, or repair of the emission control device and systems may be performed by any non-road engine repair establishment or individual.
EBZ8001 9. Maintenance SPARK PLUG • The spark plug may gather carbon deposits on its firing end with reasonable use. Remove and inspect the spark plug every 25 hours and clean the electrodes as necessary with a wire brush. The spark gap should be adjusted to .025 in (0.6~0.7mm). (1) (2) (3) (4) • Plug manufacturers recommend replacing the plug twice a year to avoid unexpected plug failure in a job. REPLACEMENT PLUG IS NGK CMR7H.
EBZ8001 9. Maintenance AIR INLET NET IMPORTANT • Blowing air is taken in from the air inlet net. When air flow has dropped down during operation, stop the engine and inspect the air inlet net for blocking by obstacles. • Note that failure to remove any such obstacles may result in the engine becoming overheated and damaged. HARNESS • If the harness is damaged it may break during use, thus causing the product to fall and resulting in personal injury.
EBZ8001 12. Troubleshooting guide Case 1. Starting failure CHECK fuel tank fuel filter carburetor adjustment screw sparking (no spark) spark plug → → → → → → PROBABLE CAUSES incorrect fuel fuel filter is clogged out of normal range spark plug is fouled/wet plug gap is incorrect disconnected Case 2.
