EXZ2610DL 115 62 07-26 (309) OWNER’S MANUAL MULTI PURPOSE TRIMMER EXZ2610DL GB-1 01-EXZ2610DL_四 Page 1 13.10.16, 9:26 AM Adobe PageMaker 6.
EXZ2610DL EXPLANATION OF SYMBOLS AND SAFETY WARNINGS WARNING!!! RISK OF DAMAGING HEARING Wear head, eye and ear protection. MODEL BC-EX LRT-EX PS-EX2 25.4 cm3 25.4 cm3 25.4 cm3 SOUND LEVEL1) ISO 22868 ISO 11094 ISO 11680-1 LwA LpAeq guaranteed 95 dB(A) 99 dB(A) 118 dB(A) 96 dB(A) VIBRATION LEVEL2) ISO 22867 ahv.eq 5.3 m/s2 5.
EXZ2610DL EC DECLARATION OF CONFORMITY (Applies to Europe only) The undersigned manufacturer, Husqvarna Zenoah Co.,Ltd., 1-9, Minamidai, Kawagoe, Saitama, Japan, declares under sole responsibility that the following products referred to in this declaration conform with the requirement of the following COUNCIL’S DIRECTIVE. The products referred to are : DESIGNATION MANUFACTURER MODEL SERIAL NUMBERS DATING : MULTI PURPOSE TRIMMER : Husqvarna Zenoah Co., Ltd.
EXZ2610DL 1. Parts location EXZ2610DL-PUO 14 6 1 2 3 13 4 7 9 12 5 8 11 BC-EX 16 15 17 LRT-EX 18 19 PS-EX2 10 11. Loop handle 12. Suspension point 13. Stop switch 14. Throttle cable 15. Throttle trigger 16. Throttle set button 17. Shaft tube 18. Knob bolt 19. Spark arrester 10. Stater knob 11. Fuel tank 12. Primer 13. Choke lever 14. Air cleaner cover 15. Trimmer guard 16. Angle transmission 17. Trimmer head 18. Blade 19. Transmission 20. Guide bar 21. Saw chain 22. Chain cover 23.
EXZ2610DL 2. Specification Engine Type ............................................................................ Air-cooled 2-stroke gasoline Model ............................................................................................ Zenoah GZ25N Displacement ........................................................................................... 25.4 cm3 Max. output .................................................. 1.2 Hp (0.9 kW) at 7500/min-1 (rpm) Idle speed ..............................
EXZ2610DL 3. Warning labels on the machine 15m (50ft) (1) (1) (2) (3) (4) (5) (6) (7) (2) (3) (4) (5) (6) (7) Read owner’s manual before operating this machine. Wear head, eye and ear protection. Wear foot protection. Wear gloves. Beware of thrown objects. Warning / Attention Keep all children, bystanders and helpers 15 meters away from the machine.
EXZ2610DL 5. For safe operation 1. Read this manual carefully until you completely understand and follow all safety and operating instructions. 2. Keep this manual handy so that you may refer to it later whenever any questions arise. Also note, if you have any questions which cannot be answered herein, contact the dealer from whom you purchased the product. 3. Always be sure to include this manual when selling, lending, or otherwise transferring the ownership of this product. 4.
EXZ2610DL 5. For safe operation BEFORE STARTING THE ENGINE 1. The area within a perimeter of 15 m of the person using the product should be considered a hazardous area into which no one should enter. If necessary, yellow warning rope, warning signs should be placed around the perimeter of the area.
EXZ2610DL 5. For safe operation (PS-EX only) 7. Never operate the pruner at an angle greater than 60° in order to reduce the risk of being struck by falling objects during operation. WARNING Approaching or contacting electric power lines with the pruner may cause serious injury or death from electrocution. Electricity can jump from one point to another by means of arcing or may be conducted through damp branches.
EXZ2610DL 5. For safe operation (PS-EX only) 1. When you finish cutting in one location and wish to continue work in another spot, turn off the engine, lift up the unit and carry it paying attention to the blade. 2. Never forget to place the protective cover over the blades. 3. When hand-carrying the product, cover over the cutting attachment if necessary, lift up the product and carry it paying attention to the cutting attachment. 4.
EXZ2610DL 6. Set up A Package contains the items as illustrated.
EXZ2610DL 6. Set up MOUNTING ENGINE INSTALLING HANDLE (BC-EX, LRT-EX only) NOTE The handle is put during the arrow mark. 1. Push the shaft tube toward the clutch housing and rotate it by hand to check that the power transmission shaft is engaged with the gears. 2. Insert the power transmission shaft into the clutch housing until it bottoms, and align the positioning holes on the clutch housing and the shaft tube and install the screw. When difficult to engage, twist the engine slightly. 3.
EXZ2610DL 6. Set up (BC-EX only) INSTALLING CUTTING ATTACHMENT GUARD FOR TRIMMER HEAD • Attach the cutting attachment guard with the bolts combined to the shaft tube while inserting the spacer between the guard and the shaft tube. 4. When correctly adjusted, check the correct working of the harnesses' QUICK RELEASE. INSTALLING TRIMMER HEAD 1. While locking the gear shaft, by inserting the supplied tool into the upper holder on the angle transmission, loosen and remove the hexagon nut (left-handed). 2.
EXZ2610DL 6. Set up (LRT-EX only) 6. Set up (PS-EX2 only) ATTACHING THE TRIMMING MECHANISM ATTACHING THE PRUNING MECHANISM (1) (4) (2) (3) (1) Tube (2) Transmission (3) Screw hole (4) Screw (5) Fastening bolt (5) 1. Remove the screw screwed into the end of the transmission. 2. Insert the end of the tube into the transmission. 3. Line up the hole on the end of the transmission into which the screw is to be inserted with the screw hole on the tube, and screw the screw firmly in. 4.
EXZ2610DL 6. Set up (PS-EX2 only) WARNING WARNING Pay attention to the correct direction of the saw chain. 3. Fit the chain tension adjuster nut into the lower hole of the guide bar, then install the chain cover, and fasten the mounting nut to finger tightness. BALANCE UNIT 1. Put on harness and attach unit to harness. 2. Depending on the working posture, slide clamp up or down until unit balances and the harness fits your body.
EXZ2610DL 7. Fuel and chain oil ■ FUEL WARNING • Gasoline is very flammable. Avoid smoking or bringing any flame or sparks near fuel. Make sure to stop the engine and allow it cool before refueling the unit. Select outdoor bare ground for fueling and move at least 3 m (10 ft) away from the fueling point before starting the engine. • The Zenoah engines are lubricated by oil specially formulated for air-cooled 2-cycle gasoline engine use.
EXZ2610DL 8. Operation STARTING ENGINE WARNING The cutting attachment will start rotating upon the engine starts. 5. Set the stop switch to the “-” position. Set the throttle trigger to the start position (1 → 2 → 3). Place the unit on a flat, firm place. Keep the cutting head clear of everything around it. (1) 1 1. Feed fuel into the fuel tank and tighten the cap securely. 2 3 (1) Stop switch 6. While holding the unit firmly, pull out the starter rope quickly until engine fires.
EXZ2610DL 8. Operation 7. Move the choke lever downward to open the choke. And restart engine. (1) (2) (3) ADJUSTING THROTTLE CABLE • The normal play (1) of the throttle cable (2) is 1 or 2mm when measured at the carburetor side end. Turn the cable adjuster (3) in clockwise or counterclockwise to obtain the normal play. After that lock the cable adjuster by tightening the nut (4) up.
EXZ2610DL 8. Operation (BC-EX only) CUTTING WORK (TRIMMER HEAD USAGE) WARNING 1. Always wear eye protection such as safety goggles. Never lean over the rotating cutting attachment. Rocks or other debris could be thrown into eyes and face and cause serious personal injury. 2. Keep the cutting attachment guard in place at all times when the unit is operated. TRIMMING GRASS AND WEEDS • Always remember that the TIP of the line does cutting.
EXZ2610DL 8. Operation CUTTER CUTTER APPLIAPPLICATION CATION CHART CHART (Optional blade usage BC-EX only) 9” 9" 8-tooth: 8-tooth: 6298-15343 9” 9" 4-tooth: 4-tooth: 6298-14243 Trimmer head head 848-BU3-6914 Heavy Heavy weeds weeds Light Light weeds weeds Grass Grass CHOOSE THE BLADE Choose a suitable recommended cutting attachment according to the object to be cut. IMPORTANT Change the loop handle to the J-handle for safe operation.
EXZ2610DL 8. Operation (Optional blade usage BC-EX only) STARTING THE ENGINE Please refer to 5. For safe operation (P. 7 ~ 9), 8. Operation (P. 16 ~ 17). WARNING The product is equipped with a centrifugal clutch mechanism, so the cutting attachment begins to rotate as soon as the engine is started by putting the throttle trigger into the start position.
EXZ2610DL 8. Operation (Optional blade usage BC-EX only) WARNING Make sure to use harness and cutting attachment guard. If not, it is very dangerous when you slip or lose your balance. MAINTENANCE BLADE • Check the blade and the fasteners for looseness, cracking, or bending. • Check the cutting edges and reform with a flat file. Point: WARNING Saw blade CONTROLLING BLADE BOUNCE Blade thrust can cause serious personal injury. Carefully study this section.
EXZ2610DL 8. Operation (LRT-EX only) WARNING This product is equipped with extremely sharp blades, and when used improperly these blades can be extremely dangerous and improper handling can cause accidents, which may in turn lead to serious injury or death. For this reason, you should always be careful to follow the following instructions when using your trimmer. • Never hold the trimmer in a way in which the blades are pointed towards someone else.
EXZ2610DL 8. Operation (PS-EX2 only) Adjust the pump as follows: 1. Stop the engine and make sure the stop switch is in the OFF position. (b) 30° (c) 30° (a) 2. With a screwdriver, turn the oil flow rate adjusting screw to the desired direction. (a) Clockwise-oil flow increase (b) Counter clockwise-oil flow decrease (c) Middle WARNING • Always wear work gloves made of leather or some other sturdy material when using the pruner.
EXZ2610DL CUTTING UNIT SHAFT ENGINE 9. Maintenance Every Every Every Every 25 50 100 Before 15 System/components Procedure Note hours hours hours hours use after after after after fuel leaks, fuel spillage wipe out ✔ fuel tank, air filter, fuel filter inspect/clean ✔ ✔ replace, if necessary see adjusting replace carburetor idle speed adjuster ✔ idling speed (p. 22) if necessary GAP: .025 in (0.6 ~ 0.
EXZ2610DL 9. Maintenance SPARK PLUG • Starting failure and misfiring are often caused by a fouled spark plug. Clean the spark plug and check that the plug gap is in the correct range. For a replacement plug, use the correct type specified by ZENOAH. SPARK ARRESTER • The muffler is equipped with a spark arrester to prevent red hot carbon from flying out of the exhaust outlet. Periodically inspect and clean as necessary with a wire brush in the repair specialty store.
EXZ2610DL 9. Maintenance IMPORTANT • If waste gets stuck and causes blockage around the intake air cooling vent, it may cause the engine to overheat, and that in turn may cause mechanical failure on the part of the brushcutter. 9. Maintenance (BC-EX only) REFILLING TRIMMING LINE 1. For replacement line, use a diameter of 2.4mm(.095in). The spool is capable for a line upto 6m(20ft) on the 10cm(4”) head. Avoid using a larger line as it may cut down the trimming performance.
EXZ2610DL 9. Maintenance (BC-EX only) 9. Maintenance (LRT-EX only) ANGLE TRANSMISSION BLADES • When refilling the tank or resting, it is often a good idea to use the time to oil the cutting blades. • If a gap exists between the upper and lower blades, follow the procedure below to adjust them so that they fit more closely together. • The reduction gears are lubricated by multipurpose, lithium-based grease in the angle transmission.
EXZ2610DL 9. Maintenance (PS-EX2 only) OILING PORT Dismount the guide bar and check the oiling port for clogging. (1) DRIVE SPROCKET Regularly check the degree of wear on the drive sprocket. Replace if wear is excessive. (1) Oiling port GUIDE BAR Remove sawdust in the guide bar groove and the oiling port. (1) Drive Sprocket (1) OTHERS Check for fuel leakage and loose fastenings or damage to major parts, especially housing joints and guide bar mounting.
EXZ2610DL 9. Maintenance (PS-EX2 only) SAW CHAIN After every cutter has been set, check the depth gauge and file it to the proper level as illustrated. WARNING It is very important for smooth and safe operation to keep the cutters always sharp. Your cutters need to be sharpened when: • Sawdust becomes powder-like. • You need extra force to saw in. • The cut way does not go straight. • Vibration increases. • Fuel consumption increases. Cutter setting standards: 0.25" (0.
EXZ2610DL 12. Troubleshooting guide Case 1. Starting failure CHECK fuel tank fuel filter carburetor adjustment screw sparking (no spark) spark plug → → → → → → PROBABLE CAUSES incorrect fuel fuel filter is clogged out of normal range spark plug is fouled/wet plug gap is incorrect disconnected → → → → → → ACTION drain it and use correct fuel clean adjust to normal range clean/dry correct (GAP: 0.6 ~ 0.
To Dealer: Please complete the following form at time of sale. Product Model: ZENOAH EXZ2610 BC-EX LRT-EX PS-EX2 Date of Purchase: D / M / Y Equipment No.: Engine No.: Use: Private: Professional Rental Purchaser: Name: Dealer: Address/Phone: Name: Address/Phone: To Purchaser: When your unit requires any repair, please bring or send it to the dealer with this sheet attached. PRINTED IN JAPAN 01-EXZ2610DL_四 Page 32 13.10.16, 9:26 AM Adobe PageMaker 6.