HB2302 / HBZ2602 115 33 78-10 (001) Original Instruction G B OWNER’S MANUAL BLOWER HB2302 HBZ2602 GB-1
HB2302 / HBZ2602 EC DECLARATION OF CONFORMITY (Applies to Europe only) The undersigned manufacturer, Husqvarna Zenoah Co.,Ltd., 1-9, Minamidai, Kawagoe, Saitama, Japan, declares under sole responsibility that the following products referred to in this declaration conform with the requirement of the following COUNCIL’S DIRECTIVE. The products referred to are : DESIGNATION MANUFACTURER MODELS : BLOWER (Hand-held garden blower) : Husqvarna Zenoah Co., Ltd.
HB2302 / HBZ2602 SAFETY FIRST Instructions contained in warnings within this manual marked with a symbol concern critical points which must be taken into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions carefully and follow them without fail. WARNINGS IN THE MANUAL WARNING This mark indicates instructions, which must be followed in order to prevent accidents, which could lead to serious bodily injury or death.
HB2302 / HBZ2602 2. Specification Model Dimesion (L x W x H) ** Dry weight* Fuel tank capacity HB2302 HBZ2602 327 x 225 x 360 327 x 269 x 360 kg 3.9 4.2 liter 0.75 0.65 Air cooled Strato-charged air cooled Engine Type 2-cycle gasoline engine 2-cycle gasoline engine Displacement cm3 22.5 25.4 Air filter Dry polyurethane foam Carburetor Diaphragm, rotary valve type Ignition system T.C.I. C.D.I.
HB2302 / HBZ2602 5. For safe operation WARNING 1. Read this manual carefully until you completely understand and follow all safety and operating instructions. 2. Keep this manual handy so that you may refer to it later whenever any questions arise. Also note, if you have any questions which cannot be answered herein, contact the dealer from whom you purchased the product. 3. Always be sure to include this manual when selling, lending, or otherwise transferring the ownership of this product. 4.
HB2302 / HBZ2602 5. For safe operation 8. The ignition system of your unit produces an electromagnetic field of a very low intensity. This field may interfere with some pacemakers. To reduce the risk of serious or fatal injury, persons with pacemaker should consult their physician and the pacemaker manufacturer before operating this tool.
HB2302 / HBZ2602 5. For safe operation WARNING • Never use the blower without the screen at the air intake of the blower. Before each use, check that, the screw (1) is securely tightened and is free from any damage. • Never remove debris from the intake screen while the engine is running. Contact with rotating blower fan may result in a serious personal injury.
HB2302 / HBZ2602 5. For safe operation WARNING The temperature of the machine may increase after stopping the engine. Especially never forget to cool down the engine before refueling the machine. 10. After using blowers and other equipment, CLEAN UP! Dispose of debris in trash receptacles. MAINTENANCE 1. In order to maintain your product in proper working order, perform the maintenance and checking operations described in the manual at regular intervals. 2.
HB2302 / HBZ2602 6. Set up BLOWER PIPE • Align groove in blower pipe with projection on blower housing. G B • Slide the pipe onto the blower housing. INSTALLING SUPPORT HANDLE • This handle is supplied with the blower. • Fit the holes of volute and handle, tighten the screws. • Be sure to tighten the screws straightly. (1) Support Handle (2) Holes (3) Screws • Rotate the pipe clockwise to lock it into place.
HB2302 / HBZ2602 7. Fuel ■ FUEL • Gasoline is very flammable. Avoid smoking or bringing any flame or sparks near fuel. Make sure to stop the engine and allow it cool before refueling the unit. Select outdoor bare ground for fueling and move at least 3 m (10 ft) away from the fueling point before starting the engine. • The Zenoah engines are lubricated by oil specially formulated for air-cooled 2-cycle gasoline engine use.
HB2302 / HBZ2602 8. Operation STARTING ENGINE 1. Rest the unit on a flat, firm place. 2. Pump the primer until fuel flows out in the clear tube. (1) Primer 3. Move the choke lever upward to close the choke. 6. When the engine has started, move the choke lever gradually downward to open the choke. 7. Allow the engine to warm up for a half minute before starting operation. RESTARTING ENGINE WHILE ENGINE IS HOT 1. When restarting the engine immediately after stopping it, leave the choke open. 2.
HB2302 / HBZ2602 9. Maintenance Maintenance, replacement, or repair of the emission control device and systems may be performed by any non-road engine repair establishment or individual.
HB2302 / HBZ2602 9. Maintenance FUEL FILTER • A clogged fuel filter may cause poor acceleration of the engine. Check periodically to see if the filter is clogged with dirt. The filter can be taken out of the fueling port using a small wire hook. Disconnect the filter assembly from the fuel pipe and unhook the retainer to disassemble it. Clean the components with gasoline. MUFFLER WARNING • Inspect periodically, the muffler for loose fasteners, any damage or corrosion.
HB2302 / HBZ2602 9. Maintenance 10. Storage AIR INTAKE SCREEN (AIR INLET NET) BEFORE STORING THE BLOWER: 1. Drain a fuel tank and push the primer bulb until it becomes empty of fuel. 2. Remove the spark plug and drop a spoonful of 2-cycle oil into the cylider. Crank the engine several times and install the spark plug. 3. Store unit in a dry, dust free place, out of the reach of children. IMPORTANT • Blowing air is taken in from the air inlet net.
HB2302 / HBZ2602 13. Troubleshooting guide Case 1. Starting failure CHECK fuel tank fuel filter carburetor adjustment screw sparking (no spark) spark plug → → → → → → PROBABLE CAUSES incorrect fuel fuel filter is clogged out of normal range spark plug is fouled/wet plug gap is incorrect disconnected Case 2.
