NS2522 115 34 40-10 (002) G B OWNER’S MANUAL POWER SPRAYER NS2522 Original Language GB-1
NS2522 EC DECLARATION OF CONFORMITY (Applies to Europe only) The undersigned manufacturer, Husqvarna Zenoah Co.,Ltd., 1-9, Minamidai, Kawagoe, Saitama, Japan, declares under sole responsibility that the following products referred to in this declaration conform with the requirement of the following COUNCIL’S DIRECTIVE. The products referred to are : DESIGNATION MANUFACTURER MODELS SERIAL NUMBERS DATING : Power sprayer : Husqvarna Zenoah Co., Ltd.
NS2522 SAFETY PRECAUTIONS Contents Warning labels bearing the mark on the product and in this Manual refer to important safety matters. Please familiarize yourself with them and observe them well. If a warning label on the product becomes soiled or detached, please order a replacement label from your dealer and attach it in the requisite place. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13.
NS2522 2.
NS2522 5. For safe operation Before using this product, please read this Operator's Manual thoroughly to ensure correct operation. The following are precautions that should be observed in order to use the product smoothly. Elsewhere in the Manual, the warning mark is used to bring your attention to these precautions. BEFORE USING THE PRODUCT • This product has been designed mainly for the purpose of spraying pest control chemicals and weedkillers.
NS2522 5. For safe operation IMPORTANT Check and follow the local regulations as to sound level and hours of operations for the product. PRECAUTIONS BEFORE SPRAYING • Make sure you have the correct protective clothing, headgear, rubber gloves and boots, a protective mask, goggles, a towel, protective cream, etc., to prevent chemicals from coming into contact with your skin or entering your lungs. When spraying, please wear this protective gear to prevent any risk of injury. 1. 2. 3. 4. 5. 6. 7. 8. 9.
NS2522 5. For safe operation • While spraying please be careful of the wind direction and always stand on the upwind side, to avoid spraying yourself with chemicals. • Should you begin to feel even slightly unwell while spraying, consult a doctor immediately. When doing so, inform the doctor of the name of the chemical you were using, the conditions of use, etc. • If the sprayer is tilted the chemical may leak out through the air holes in the cap.
NS2522 6. Set up A Package contains the items as illustrated.
NS2522 6. Set up ■ Connecting the spray hose and nozzle ■ Adjusting spray pressure • NS2522 has a pressure regulating dial to change spray pressure. Set the pressure at a level appropriate to the spray conditions. Set the pressure regulating dial as follows: • Turn in a clockwise direction to increase the pressure. • Turn in a counterclockwise direction to decrease the pressure. a h f e a. b. c. d. e. f. g. h.
NS2522 7. Fuel ■ FUEL WARNING • Gasoline is very flammable. Avoid smoking or bringing any flame or sparks near fuel. Make sure to stop the engine and allow it cool before refueling the unit. Select outdoor bare ground for fueling and move at least 3 m (10 ft) away from the fueling point before starting the engine. 4. Pour in the rest of gasoline and agitate again for at least one minute.
NS2522 8. Chemical filling WARNING • Chemical substances should be handled correctly, observing the precautions marked on the container. Some chemicals are extremely hazardous to humans and animals, and handling errors can cause serious poisoning or even fatal accidents. • When not in use, chemical substance containers should be stored separately from other containers out of the reach of children. ■ Procedure for filling 1.
NS2522 9. Operation 3. Place the sprayer in a stable location, and pull the starter knob with the right hand while holding the chemical tank down with the left hand. The starter knob should first be pulled out lightly, then, when resistance is felt, pulled more swiftly and vigorously. ■ Spraying WARNING • Please use correctly, observing the precautions in this Manual ("For Safe Operation", p5 to 7).
NS2522 10. Maintenance System/components ENGINE fuel leaks, fuel spillage fuel tank, air filter, fuel filter idle speed adjuster spark plug intake air cooling vent throttle lever, stop switch screws/nuts/bolts Procedure wipe out inspect/clean see adjusting idling speed clean and readjust plug gap clean check operation tighten/replace WARNING • Make sure that the engine has stopped and is cool before performing any service to the machine. Contact with hot muffler may result in a personal injury.
NS2522 10. Maintenance • When replacing plugs, please use designated items. NOTE • Warm up the engine before adjusting the idling speed. NGK (BPMR7A) IMPORTANT • If too much fuel is absorbed or poor quality oil is used, the spark plug electrodes become dirty, making the engine harder to start. • Note that using any spark plug other than those designated may result in the engine failing to operate properly or in the engine becoming overheated and damaged.
NS2522 10. Maintenance on the part of the brushcutter. G B (1) Intake air cooling vent 11. Storage WARNING • When draining fuel, please be careful not to spill it. If fuel is spilt, wipe off thoroughly. In addition, please be sure to close the storage container cap tightly. IMPORTANT • If fuel is left in the engine for protracted periods, the inside of the carburetor may become clogged and cause engine malfunction (faulty starting and insufficient output).
NS2522 13. Disposal • • When you dispose of the machine, do not disassemble the machine. When you dispose of the machine, fuel, oil, be sure to follow your local regulations. Limited warranty Should any failure occur on the product under normal operating conditions within the applicable warranty period, the failed part will be replaced or repaired free of charge by a ZENOAH® authorized dealer.
