PSZ2600 848A5393A2 (806) G B OWNER’S MANUAL POLE SAW PSZ2600 GB-1
PSZ2600 EC DECLARATION OF CONFORMITY Husqvarna Zenoah Co., Ltd. We, 1-9, Minamidai, Kawagoe, Saitama, Japan declare in sole responsibility that the following products referred to in this declaration conform with DIRECTIVE 89/336/EEC, 98/37/EC, prEN11806 : 1996 The products referred to are : DESIGNATION : POLE SAW MODELS : PSZ2600 SERIAL NUMBERS : 700101 and up The company named above will keep on file the following technical documentation for any inspection purpose.
PSZ2600 SAFETY FIRST Instructions contained in warnings within this manual marked with a symbol concern critical points which must be taken into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions carefully and follow them without fail. WARNINGS IN THE MANUAL WARNING This mark indicates instructions, which must be followed in order to prevent accidents, which could lead to serious bodily injury or death.
PSZ2600 2. Specification PSZ2600 Overall size (L x W x H) ................ 2085 x 250 x 310mm Dry weight ........................................................... 5.40kg Engine Type ................... Air-cooled 2-stroke gasoline Model .................................... Zenoah GZ25N Displacement ................................... 25.4cm3 Max. output ... 1.2Hp (0.9kW)at 7500min-1(rpm) Idle speed .................... 3000±200min-1(rpm) Fuel ....................
PSZ2600 5. For safe operation 1. Read this manual carefully until you completely understand and follow all safety and operating instructions. 2. Keep this manual handy so that you may refer to it later whenever any questions arise. Also note, if you have any questions which cannot be answered herein, contact the dealer from whom you purchased the product. 3. Always be sure to include this manual when selling, lending, or otherwise transferring the ownership of this product. 4.
PSZ2600 5. For safe operation IMPORTANT Remove any obstacle before beginning work. 4. Inspect the entire unit for loose fasteners and fuel leakage. Make sure that the cutting attachment is properly installed and securely fastened. 5. Always use the shoulder strap. Adjust the strap for comfort before starting the engine. The strap should be adjusted so the left hand can comfortably hold the handlebar grip approximately waist high. STARTING THE ENGINE 1.
PSZ2600 5. For safe operation HANDLING FUEL 1. The engine of the ZENOAH product is designed to run on a mixed fuel, which contains highly flammable gasoline. Never store cans of fuel or refill the tank of the unit in any place where there is a boiler, stove, wood fire, electrical sparks, welding sparks, or any other source of heat or fire which might ignite the fuel. 2. Never smoke while operating the unit or refilling its fuel tank. 3.
PSZ2600 6. Set up MOUNTING ENGINE A standard package contains the items as shown below. 1. Push the drive shaft housing toward the clutch housing and rotate it by hand to check that the drive shaft is engaged with the gears. 2. Insert the drive shaft housing into the clutch housing until it bottoms, and align the positioning holes on the clutch housing and the shaft tube and install the screw. When difficult to engage, twist the engine slightly. 3. Fasten the clamp securely with two screws.
PSZ2600 6. Set up 7. Fuel and chain oil 4. Adjust the chain tension by turning the tensioner screw until the tie straps just touch the bottom side of the bar rail. ■ FUEL WARNING • Gasoline is very flammable. Avoid smoking or bringing any flame or sparks near fuel. Make sure to stop the engine and allow it cool before refueling the unit. Select outdoor bare ground for fueling and move at least 3 m (10 ft) away from the fueling point before starting the engine.
PSZ2600 7. Fuel and chain oil sary for the engine to last long. Be careful that, if the agitation is insufficient, there is an increased danger of early piston seizing due to abnormally lean mixture. 5. Put a clear indication on the outside of the container to avoid mixing up with gasoline or other containers. 6. Indicate the contents on outside of container for easy identification. 8. Operation WARNING The cutting head will start rotating upon the engine starts. 1.
PSZ2600 8. Operation 6. While holding the unit firmly, pull out the starter rope quickly until engine fires. STOPPING ENGINE G B 1. Release the throttle lever and run the engine for half a minute. 2. Shift the ignition switch (a) to the STOP position. WARNING The product is equipped with a centrifugal clutch mechanism, so the cutting attachment begins to rotate as soon as the engine is started by putting the throttle into the start position.
PSZ2600 8. Operation Checking oil supply After starting the engine, run the chain at medium speed and see if chain oil has scattered off, as shown in the figure. IMPORTANT The oil flow adjusting screw must be pressed in slightly in order to turn. Failure to do so could damage the pump and screw. 3.
PSZ2600 9.
PSZ2600 9. Maintenance SPARK ARRESTER • The muffler is equipped with a spark arrester to prevent red hot carbon from flying out of the exhaust outlet. Periodically inspect and clean as necessary with a wire brush. In the State of California it is required by law (Section 4442 of the California Public Resources Code) to equip a spark arrester when a gas powered tool is used in any forest covered, brush covered, or grass covered unimproved land. 1.
PSZ2600 9. Maintenance SPROCKET Check for extensive wear, and replace it when the teeth are worn over 0.3 mm. After every cutter has been set, check the depth gauge and file it to the proper level as illustrated. (MA7) 0.3 mm G B (1) Sprocket SAW CHAIN 0.25" (0.65 mm) WARNING It is very important for smooth and safe operation to keep the cutters always sharp. Your cutters need to be sharpened when: • Sawdust becomes powder-like. • You need extra force to saw in. • The cut way does not go straight.
PSZ2600 10. Storage 11. Disposal Aged fuel is one of major causes of engine starting failure. Before storing the unit, empty the fuel tank and run the engine until it uses all the fuel left in the fuel line and the carburetor. Store the unit indoor taking necessary measures for rust prevention. When disposing your machine, fuel or oil for the machine, be sure to allow your local regulations. 12. Troubleshooting guide Case 1.
