SGCZ2600DL/SGCZ2600DW 848JN093A1 (704) G B OWNER’S MANUAL RECIPROCATORS SGCZ2600DL SGCZ2600DW GB-1
SGCZ2600DL/SGCZ2600DW EC DECLARATION OF COMFORMITY We, ZENOAH CO., LTD. 1-9, Minamidai, Kawagoe, Saitama, Japan declare in sole responsibility that the following products referred to in this declaration conform with DIRECTIVE 89/336/EEC, 98/37/EC EN ISO 11806 : 1997 2000 / 14 / EC Internal control production.
SGCZ2600DL/SGCZ2600DW SAFETY FIRST Instructions contained in warnings within this manual marked symbol concern critical points which must be taken with a into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions carefully and follow them without fail. WARNINGS IN THE MANUAL WARNING This mark indicates instructions, which must be followed in order to prevent accidents, which could lead to serious bodily injury or death.
SGCZ2600DL/SGCZ2600DW 2. Specification Model Overall size (LxWxH) Dry weight Engine SGCZ2600DL SGCZ2600DW 1930 x 250 x 250 1930 x 610 x 415 6.7 6.9 Air-cooled 2-stroke gasoline Zenoah GZ25N 1.2Hp (0.9kW) at 7500min-1 3000± 200min-1 25.4 Mixture (Gasoline 50 : Oil 1) (when using ZENOAH genuine oil) Walbro Diaphragm type NGK CMR7A 0.65 Centrifugal clutch, Rigid drive shaft 7.
SGCZ2600DL/SGCZ2600DW 5. For safe operation 1. Read this manual carefully until you completely understand and follow all safety and operating instructions. 2. Keep this manual handy so that you may refer to it later whenever any questions arise. Also note, if you have any questions which cannot be answered herein, contact the dealer from whom you purchased the product. 3. Always be sure to include this manual when selling, lending, or otherwise transferring the ownership of this product. 4.
SGCZ2600DL/SGCZ2600DW 5. For safe operation BEFORE STARTING THE ENGINE 1. The area within a perimeter of 15 m (50 ft) of the person using the product should be considered a hazardous area into which no one should enter. If necessary, yellow warning rope, warning signs should be placed around the perimeter of the area.
SGCZ2600DL/SGCZ2600DW 5. For safe operation could result in serious burns or electrical shock. • IF SOMEONE COMES 1. Guard against hazardous situations at all times. Warn adults to keep pets and children away from the area. Be careful if you are approached. Injury may result from flying debris. 2. If someone calls out or otherwise interrupts you while working, always be sure to turn off the engine before turning around. MAINTENANCE 1.
SGCZ2600DL/SGCZ2600DW 6. Set up MOUNTING ENGINE 1. Install the engine to the drive shaft so that the cylinder head and the stop switch may come on the same side. 2. Using attached four bolts, secure the connection firmly with equal force (Torque: 25in-lbs)(Torque: 2.8 N.m.). MOUNTING ENGINE Install the engine to the drive shaft. Using attached 4 socket screws, secure the connection firmly with equal force. Bolt Stop switch INSTALLING HANDLE 1.
SGCZ2600DL/SGCZ2600DW 6. Set up CUTTERCASE WARNING The blade has very sharp edges. Be sure to use protective gloves whenever handling it. G B 1. Remove the fastening screw(long) and the lock screw(short) from the cuttercase. 2. While aligning the locking holes, install the cuttercase assembly to the shaft casing. 3. Align the locking holes and screw in the lock screw to the bottom by hand, then secure it with the wrench provided.
SGCZ2600DL/SGCZ2600DW 7. Fuel ■ FUEL WARNING • Gasoline is very flammable. Avoid smoking or bringing any flame or sparks near fuel. Make sure to stop the engine and allow it cool before refueling the unit. Select outdoor bare ground for fueling and move at least 3 m (10 ft) away from the fueling point before starting the engine. • The Zenoah engines are lubricated by oil specially formulated for air-cooled 2-cycle gasoline engine use.
SGCZ2600DL/SGCZ2600DW 8. Operation 8. While holding the unit firmly, pull out the starter rope quickly. STARTING ENGINE WARNING The cutting head will start rotating upon the engine starts. 1. Rest the unit on a flat, firm place. Keep the cutting head off the ground and clear of surrounding objects as it will start rotating upon starting of the engine. 2. Push the primer pump several times until overflown fuel flows out in the clear tube.
SGCZ2600DL/SGCZ2600DW 8. Operation ADJUSTING THE MAXIMUM SPEED • The screw at the throttle lever is for adjusting the maximum rpm. • Turning the screw crock-wise, the rpm becomes down, the otherwise, the rpm becomes up. (STANDARD OPERATION SPEED: 8000 to 9500 rpm) Running engine with faster engine speed than 9500 rpm may damage the engine, slower engine speed than 8000 rpm may cause of the poor cutting ability.
SGCZ2600DL/SGCZ2600DW 8. Operation CUTTING WORK This machine does cutting not by a rotary cutter like conventional trimmers but by a pair of special blades that moves round within a limited angle at a speed of approximately 1/30 of conventional trimmers. This unique mechanism has brought you many benefits as following; 1. Since the blade does not cause grass chips and pebbles to be thrown around, you may use less care about your clothing or surrundings. 2.
SGCZ2600DL/SGCZ2600DW 9.
SGCZ2600DL/SGCZ2600DW 9. Maintenance WARNING Make sure that the engine has stopped and is cool before performing any service to the machine. Contact with moving cutting head or hot muffler may result in a personal injury. AIR FILTER • The air filter, if clogged, will reduce the engine performance. Check and clean the filter element in warm, soapy water as required. Dry completely before installing. If the element is broken or shrunk, replace with a new one.
SGCZ2600DL/SGCZ2600DW 9. Maintenance INTAKE AIR COOLING VENT PROCEDURES TO BE PERFORMED AFTER EVERY 100 HOURS OF USE WARNING • Never touch the cylinder, muffler, or spark plugs with your bare hands immediately after stopping the engine. The engine can become very hot when in operation, and doing so could result in severe burns.
SGCZ2600DL/SGCZ2600DW 12. Troubleshooting guide Case 1. Starting failure CHECK fuel tank fuel filter carburetor adjustment screw sparking (no spark) spark plug → → → → → → PROBABLE CAUSES incorrect fuel fuel filter is clogged out of normal range spark plug is fouled/wet plug gap is incorrect disconnected Case 2.
