Use, Care, and Installation Guide www.zephyronline.com Titan Island AK7736AS AK7742AS AK7748AS Model number: Serial Number: SEP19.
www.zephyronline.
INSTALLATION Ducting Calculation Sheet........................................ Mounting Height & Clearance................................. Ducting Options............................................................ Hood Specifications.................................................... Mounting the Hood...................................................... PBD-1300A Dual Blower Ducting.......................... 5 6 7 8 9-11 12 FEATURES & CONTROLS Electronic LCD Controls..................................
www.zephyronline.com Important Safety Notice READ AND SAVE THESE INSTRUCTIONS WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THIS FAN WITH ANY SOLID-STATE CONTROL DEVICE. WARNING TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: a. Use this unit only in the manner intended by the manufacturer, if you have questions, contact the manufacturer. b.
Always leave safety grilles and filters in place. Without these components, operating blowers could catch onto hair, fingers and loose clothing. The manufacturer declines all responsibility in the event of failure to observe the instructions given here for installation, maintenance and suitable use of the product. The manufacturer further declines all responsibility for injury due to negligence and the warranty of the unit automatically expires due to improper maintenance. *NOTE: Please check www.
List of Materials www.zephyronline.com MODELS: AK7736AS, AK7742AS, AK7748AS PARTS SUPPLIED 1 - Hood 4 - Duct covers, 2 upper & 2 lower 2 - Support frames, 1 upper & 1 lower 2- Angled support brackets 1- Middle support frame 4 - Baffle filters, AK7736AS & AK7742AS 6 - Baffle filters, AK7748AS 2 - LED light bulbs, AK7736AS & AK7742AS 4 - LED light bulbs, AK7748AS 1 - 8 in.
Duct pieces Total 1 Ft. x( ) = Ft. 6”, 7”, 8”, 10” 1 Ft. Round, straight x( ) = Ft. 3-1/ 4” x 10” Rect. 90 0 elbow 15 Ft. x( ) = Ft. 3-1/ 4” x 10” Rect. 45 0 elbow 9 Ft. x( ) = 3-1/ 4” x 10” Rect., straight Equivalent number length x used = Total 3-1/ 4” x 10” 5 Ft. Rect. to 6” round transition x( ) = Ft. 3-1/ 4” x 10” 20 Ft. Rect. to 6” round transition 90 0 elbow x( ) = Ft. 6” round to 1 Ft. 3-1/ 4” x 10” rect. transition x( ) = Ft. Ft. x( ) = Ft. 24 Ft. x( ) = Ft.
Installation – Mounting Height & Clearance www.zephyronline.com ALWAYS, when possible, reduce the number or transitions and turns. If long duct run is required, increase duct size. If turns or transitions are required; install as far away from hood duct output and as far apart, between the two as possible. Minimum mount height between range top to hood bottom should be no less than 24”. A n. mi . B x ma C n. mi . D x ma Maximum mount height should be no higher than 36”. in. ” max.
NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or garages. All exhaust must be ducted to the outside. Use rigid metal ductwork only. Fasten all connections with sheet metal screws and tape all joints with certified Aluminum Tape or Duct Tape.
16 1/4” Standard Min. - 33” Max. - 50“ 14 5/16” Z1C-0077 (36”, 42“) Z1C-0177 (48”) Min. - 49” Max. - 78” 4” 3 5/16” 27 15/16” 17 15/16” (36”, 42“) 21 5/8” (48”) 35 15/16” (36”) 41 15/16” (42”) 47 15/16” (48”) 31 5/8” FRONT SIDE 13 1/4” (36”, 42“) 16 15/16” (48”) 6 15/16” (36”, 42“) 8 3/4” (48”) 18” (36”) 20 15/16” (42”) 23 15/16” (48”) C/L 2 3/16” 11 7/16” C/L 14 9/16” 16 5/8” 7 7/8” C/L Installation – Hood Specifications www.zephyronline.
FRONT B Ceiling Joists 1 Wood Blocking Cut-Out Shaded Area 2 Top Support Frame A XP022220 FIG. B 3 Support Frame Arm Bottom Support Frame 4 Mounting Screws (pre-installed) Hood Body FIG. A 1. Determine mounting location on ceiling and temporarily tape paper template (included with the hood) to the ceiling. Cut out internal shaded area of template to allow the ducting and electrical to pass through. If necessary, add wood blocking (min.
Duct Cover Standard Frame Assembly Instructions Top Support Frame 1. Front top e Sid 1/2 bottom Installation – Mounting the Hood www.zephyronline.com FIG. D FIG. F 2. Bottom Support Frame (secures to top of blower housing) back 3. Key Holes front - facing controls FIG. C FIG. E 3. Attach square support bracket inside the support frame assembly. The placement of the square support bracket should preferably be aligned in the middle where the top and bottom frame intersect (FIG.
Top Duct Covers Cable Lock A cable locking connector (not supplied) might be required by local codes. Check with local requirements and codes, purchase and install appropriate connector if necessary. Bottom Duct Covers Cable Lock Side nt Fro Bottom Support Frame FIG. G FIG. H ! WARNING: Electrical wiring must be done by a qualified person(s) in accordance with all applicable codes and standards. This range hood must be properly grounded. Turn off electrical power at service entrance before wiring.
www.zephyronline.com Installation – PBD-1300A Dual Blower Ducting This range hood is equipped standard with a single blower vertical duct option. To convert from single blower vertical ducting to dual blower vertical ducting please following the instructions below. 1. Disconnect blower plug and white and black power cables. 2. Remove (4) screws from interior of hood body attaching single blower plate to top of hood body. Remove single blower and single blower plate. 3.
Display Adjust 6 Speed Levels Lights On/Dim/Off 1. Power / Delay Off Power Button Function On/Off button will turn power on and off for entire hood (fan and lights). The hood will remember the last speed and light level it was turned off at. Delay Off Button Function With the fan on, press and hold the On/Off button for three seconds. The fan will change to speed 1 and the 10 minute delay off timer will start.
Features & Controls – Optional Remote Control FCC Caution: To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. (Example - use only shielded interface cables when connecting to computer or peripheral device. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions.
Do not use corrosive detergents, abrasive detergents or oven cleaners. Do not use any product containing chlorine bleach or any product containing chloride. Do not use steel wool or abrasive scrubbing pads which will scratch and damage surface. Cleaning Stainless Steel Clean periodically with warm soapy water and clean cotton cloth or micro fiber cloth. Always rub in the direction of the stainless 2 steel grain. To remove heavier grease build up use a liquid degreaser detergent.
Troubleshooting www.zephyronline.com TROUBLESHOOTING PROCEDURES Issue Cause What to do After installation, the unit doesn’t work. 1. The power source is not turned ON. 1. Make sure the circuit breaker and the unit’s power is ON. 2. The power line and the cable locking connector is not connecting properly. 2. Check the power connection with the unit is connected properly. 3. The switch board and control board wirings are disconnected. 3.
Some local codes limit the maximum amount of CFM a range hood can move. ACT™ allows you to control the maximum blower CFM of select Zephyr Ventilation range hoods without the need for expensive make up air kits. ACT™ enables the installer to easily set the maximum blower speed to one of two most commonly specified CFM levels; 590, 390 or 290 CFM. The usage of ACT™ may not be necessary for your installation. Please check your local codes for CFM restrictions.
Wiring Diagrams www.zephyronline.com ACT 590 CFM - Fan Max. 175W @ 2.6A ACT 390 CFM - Fan Max. 94W @ 1.4A ACT 290 CFM - Fan Max. 63W @ 0.
PART# Replacement Parts LED Light Bulb MR16 (GU10) 6W (each) Baffle Filter (each) Z0B0040 50210036 Optional Accessories Duct Cover Extension (36”, 42”) Duct Cover Extension (48”) Dual Internal Blower Make-Up Air Kit (Single Blower) Make-Up Air Kit (Dual Blower) Z1C-0077 Z1C-0177 PBD-1300A MUA008A MUA010A To order parts, visit us online at http://store.zephyronline.com or call us at 1.888.880.
Warranty www.zephyronline.
PRODUCT REGISTRATION Congratulations on the purchase of your Zephyr product! Please take a moment to register your new Zephyr product at www.zephyronline.com/registration IT’S IMPORTANT Prompt registration helps in more ways than one. Ensures warranty coverage should you need service. Ownership verification for insurance purposes. Notification of product changes or recalls. Zephyr Ventilation | 2277 Harbor Bay Pkwy. | Alameda, CA 94502 21 | 1.888.880.
Guide d’utilisation, d’entretien et d’installation www.zephyronline.com Titan Island AK7736AS AK7742AS AK7748AS Numéro de modèle : Numéro de série : Date d’achat : Détaillant: SEP19.0101 © Zephyr Ventilation LLC.
www.zephyronline.
INSTALLATION Feuille de calcul pour le conduit................................................................................... 5 Espace libre et hauteur de montage.......................................................................... 6 Options d’installation pour le conduit......................................................................... 7 Spécifications.......................................................................................................................
www.zephyronline.com Mise en garde de sécurité LISEZ ET CONSERVEZ CES INSTRUCTIONS AVERTISSEMENT POUR RÉDUIRE LES RISQUES D’INCENDIE OU DE DÉCHARGE ÉLECTRIQUE, N’UTILISEZ PAS CET APPAREIL AVEC UN TABLEAU DE COMMANDE À SEMI-CONDUCTEURS. AVERTISSEMENT POUR RÉDUIRE LES RISQUES D’INCENDIE, DE DÉCHARGE ÉLECTRIQUE OU DE BLESSURE, RESPECTEZ CES CONSIGNES : a. N’utilisez cet appareil que de la manière prévue par le fabricant. Si vous avez des questions, communiquez avec le fabricant. b.
POUR RÉDUIRE LES RISQUES D’INCENDIE, N’UTILISEZ QUE DES CONDUITS D’AÉRATION EN MÉTAL. ATTENTION Pour réduire les risques d’incendie et pour évacuer l’air convenablement, assurez-vous de canaliser l’air à l’extérieur de la maison. N’installez pas l’échappement du conduit dans les espaces entre les murs, le plafond, le grenier, les vides sanitaires ou le garage. FONCTIONNEMENT Laissez toujours les grilles de sûreté et les filtres en place.
Liste du matériel Listedu dumatériel matériel Liste www.zephyronline.com www.zephyronline.com www.zephyronline.
= 1 pi x( ) = pi 6”, 7”, 8”, 10” 1 pi circ., droit x( ) = pi 3-1/ 4” x 10” rect., coude à 90º x( ) = pi 3-1/ 4” x 10” rect., droit 3-1/ 4” x 10” rect., coude à 45º 3-1/ 4” x 10” rect., coude plat à 90º 7” to 6” or 8” to 7” circ. reducteur conique 15 pi 9 pi 24 pi 25 pi x( x( x( 15 pi 6”, 7“, 8” circ. bouchone de l’air x( 6”, 7”, 8”, 10” 15 pi circ.
Installation – Espace libre et hauteur de montage www.zephyronline.com adaptateurs sont nécessaires, installez-les le plus loin possible de l’ouverture et le plus éloigné possible l’un de l’autre. La hauteur de montage de la surface de la cuisinière au bas de la hotte ne devrait pas être inférieure à 24”. La hauteur de montage maximale ne devrait pas outrepasser 36”. Il est important d’installer la hotte à la hauteur de montage adéquate.
N’évacuez ou ne terminez JAMAIS l’échappement du conduit dans les espaces entre les murs, les vides sanitaires, le plafond, le grenier, ou le garage. Tous les échappements doivent être dirigés à l’extérieur de la maison. N’utilisez que des conduits en métal pour cloison simple. Fixez toutes les pièces du conduit avec des vis à tôle et isolez tous les joints avec du ruban à conduit en toile ou du ruban réflecteur certifié.
16 1/4” Standard Min. - 33” Max. - 50“ 14 5/16” Z1C-0077 (36”, 42“) Z1C-0177 (48”) Min. - 49” Max. - 78” 4” 3 5/16” 27 15/16” 17 15/16” (36”, 42“) 21 5/8” (48”) 35 15/16” (36”) 41 15/16” (42”) 47 15/16” (48”) 31 5/8” CÔTÉ DEVANT 13 1/4” (36”, 42“) 16 15/16” (48”) 6 15/16” (36”, 42“) 8 3/4” (48”) 18” (36”) 20 15/16” (42”) 23 15/16” (48”) C/L 2 3/16” 11 7/16” C/L 14 9/16” 16 5/8” 7 7/8” C/L Installation – Spécifications www.zephyronline.
ATTENTION : Compte tenu du poids et des dimensions de la hotte, au moins deux installateurs sont nécessaires. DEVANT B Solives de plafond 1 Bloc de bois Zone de découpage ombragée 2 Cadre de fixation supérieur A XP022220 FIG. B 3 Bras du cadre de fixation Cadre de fixation inférieur 4 Vis de montage (préinstallées) Boîtier de la hotte FIG. A 1. Déterminez l’emplacement pour l’installation de la hotte et collez temporairement le gabarit en papier (inclus avec la hotte) au plafond.
Cadre de support supérieur Couvercle des conduits Instructions d'assemblage du cadre standard 1. Devant haut té Cô 1/2 bas Installation – Montage de la hotte www.zephyronline.com FIG. F FIG. D 2. Cadre de fixation inférieur (est fixé à la partie supérieure du boîtier du ventilateur) Dos 3. Encoches en trou Devant – commandes à l’avant FIG. C FIG. E 3. Fixez le support de support carré à l’intérieur du cadre de support.
Pièces de recouvrement supérieures Raccord de câble Un raccord de câble (non inclus) pourrait également être exigé par les normes et réglementations locales. Informez-vous des exigences et des normes locales. Achetez et installez le connecteur approprié si nécessaire. Pièces de recouvrement inférieures Raccord de câble Côté nt a Dev Cadre de fixation inférieur FIG. G FIG.
Installation – Conduit avec ventilateur double PBD-1300A www.zephyronline.com Cette hotte standard est munie d’une entrée pour conduit vertical avec un ventilateur simple. Pour la convertir d’un conduit vertical à ventilateur simple à un conduit vertical à ventilateur double, veuillez suivre les instructions ci-dessous. 1. Débranchez le connecteur du ventilateur et les câbles d’alimentation blanc et noir. 2.
Tableau d’affichage Sélection de la vitesse Lumières - Allumer/Veilleuse/Éteindre 1. Mise en marche/Arrêt à retardement Fonction de mise en marche La touche On/Off permet d’allumer et d’éteindre toutes les fonctions de la hotte (ventilateur et lumières). Lorsqu’elle est éteinte, la hotte garde en mémoire la dernière vitesse du ventilateur et le dernier réglage d’intensité des lumières. Fonction d’arrêt automatique Lorsque le ventilateur est en marche, appuyez sur la touche On/Off pendant trois secondes.
Commandes – Commande à distance optionnelle www.zephyronline.com Mise en garde de la FCC : Dans le but d’assurer une conformité continue, toute modification apportée sans l’approbation expresse du parti responsable de la conformité pourrait annuler l’autorisation de l’utilisateur de faire fonctionner cet appareil. (Exemple – N’utilisez que des câbles d’interface armés lors du branchement à un ordinateur ou à un périphérique.) Cet appareil respecte l’article 15 des réglementations FCC.
Nettoyez régulièrement les surfaces de la hotte avec de l’eau savonneuse chaude et un chiffon de coton propre. N’utilisez pas de détergent abrasif ou corrosif, de laines d’acier ou de tampons à récurer; ils égratigneront et endommageront les surfaces. N’utilisez pas de produits à blanchir au chlore ou d’agents nettoyants « orange ». Pour les taches2 plus tenaces, utilisez du produit dégraissant liquide.
Dépannage www.zephyronline.com Procédures de Dépannage Problème Cause Solution Après l’installation, l’appareil ne fonctionne pas. 1. Le bloc d’alimentation n’est pas allumé 1. Assurez-vous que l’alimentation du disjoncteur et de l’appareil est allumée 2. La ligne électrique et le raccord de câble ne sont pas correctement branchés 2. Vérifiez que le branchement de l’appareil a été fait correctement 3. Les fils électriques du tableau de contrôle et de commande sont débranchés 3.
Certains codes et règlements limitent la quantité maximale de pi3/min qu’une hotte peut extraire. La ACT™ permet de contrôler la quantité maximale de pi3/min qu’évacuent un éventail de hottes Zephyr, éliminant la nécessité d’acheter un dispositif d’air d’appoint dispendieux. La ACT™ permet à l’installateur d’ajuster facilement la vitesse maximale du ventilateur à l’un des niveaux de pi3/min les plus fréquemment utilisés : 590 pi3/min ou 390 pi3/min ou 290 pi3/min.
NOIR ROUGE JAUNE ORANGE BRUN JAUNE ORANGE BRUN BLANC ROUGE BLANC NOIR VERT NOIR BLANC Modèles: AK7736AS, AK7742AS Voltage: 120V 60HZ 4A Consommation D’énergie Total: 286W Ampoule: 13W Ventilateur: 273W NOIR BLANC NOIR NOIR BLANC BLANC NOIR BLANC Thermiquement Protégé ACT 590 pi3/min — Max. du ventilateur : 175W à 2.6 A ACT 390 pi3/min — Max. du ventilateur : 94W à 1.4 A ACT 290 pi3/min — Max. du ventilateur : 63W à 0.9 A 18 JAUNE ORANGE BRUN BLANC Modèles: AK7748AS Voltage: 120V 60HZ 4.
PART # Pièces de remplacement Ampoule MR16 (GU10) 6W (unité) Filtre déflecteur (unité) Z0B0040 50210036 Accessoires Optionnels Recouvrement de conduit (36”, 42”) Recouvrement de conduit (48”) Ventilateur interne double Clapet universel d’air compensation ventilaeur double Clapet universel d’air compensation ventilaeur simple Z1C-0077 Z1C-0177 PBD-1300A MUA008A MUA010A Pour commander des pièces, visitez-nous en ligne au www.zephyronline.
Garantie www.zephyronline.
ENREGISTRMENT DU PRODUIT Nous vous félicitons d’avoir acheté une produit Zephyr. Veuillez prendre un moment pour enregistrer votre nouvelle produit au www.zephyronline.com/registration C’EST IMPORTANT Cet enregistrement rapide est utile à bien des égards. Il assure la couverture de votre garantie si vous avez besoin de service après-vente. À des fins d’assurance, il permet de confirmer que vous êtes le propriétaire.