WWW.ZEPHYRONLINE.COM Monsoon Mini II AK9528AS, AK9534AS, AK9540AS, AK9546AS EN Use, Care, and Installation Guide FR Guide d’utilisation, d’entretien et d’installation C TM Airflow Control Technology MAY21.
CORE MONSOON MINI II INSERT 2 Monsoon Mini II Use, Care, and Installation Guide
Contents ZEPHYRONLINE.COM Page Safety Information ............................................................................ 4-6 Types of Safety Warnings ................................................................... 4 General Safety ..................................................................................4-5 Operation ........................................................................................... 6 Electrical Requirements ........................................................
CORE Safety Information MONSOON MINI II INSERT READ AND SAVE THESE INSTRUCTIONS Your safety and the safety of others are very important. We have provided many important safety messages in this manual for your appliance. Always read and obey all safety messages. WARNING WARNING - TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: a) Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer.
Safety Information ZEPHYRONLINE.COM READ AND SAVE THESE INSTRUCTIONS WARNING WARNING - TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWINGa: a) SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS. If the flames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT. b) NEVER PICK UP A FLAMING PAN – You may be burned.
CORE Safety Information MONSOON MINI II INSERT READ AND SAVE THESE INSTRUCTIONS Operation Ź Always leave safety grilles and filters in place. Without these components, operating blowers could catch onto hair, fingers and loose clothing. Ź The manufacturer declines all responsibility in the event of failure to observe the instructions given here for installation, maintenance and suitable use of the product.
List of Materials ZEPHYRONLINE.
CORE Installation Instructions MONSOON MINI II INSERT Ducting Calculation Sheet Equivalent number length x used = Duct pieces 1 Ft. x( ) = Ft. 6”, 7”, 8”, 10” 1 Ft. Round, straight x( ) = Ft. 3-1/ 4” x 10” Rect. 900 elbow 15 Ft. x( ) = Ft. 3-1/ 4” x 10” Rect. 450 elbow 9 Ft. x( ) = 3-1/ 4” x 10” Rect., straight 3-1/ 4” x 10” Rect. 900 flat elbow 24 Ft. x( 7” to 6” or 25 Ft. 8” to 7” Round tapered reducer x( 15 Ft. x( 6”, 7“, 8” Round in-line damper 6”, 7”, 8”, 10” 15 Ft.
Installation Instructions ZEPHYRONLINE.COM Mounting Height, Clearance, & Ducting in..
CORE Installation Instructions MONSOON MINI II INSERT Mounting Height, Clearance, & Ducting A minimum of 7” round or 3-1/4” x 10” rectangular duct must be used to maintain maximum air flow efficiency. Always use rigid type metal ducts only. Flexible ducts could restrict air flow by up to 50%. Also use the ducting calculation sheet (on page 8) to compute total available duct run when using elbows, transitions and caps. ALWAYS, when possible, reduce the number or transitions and turns.
Installation Instructions ZEPHYRONLINE.COM Ducting Options WARNING Fire Hazard: NEVER exhaust air or terminate ductwork into spaces between walls, crawl spaces, ceilings, attics, or garages. All exhaust must be ducted to the outside, unless using the recirculating option. Ź Use single wall rigid metal ductwork only. Ź Fasten all connections with sheet metal screws and tape all joints w/ certified Silver Tape or Duct Tape.
CORE Installation Instructions MONSOON MINI II INSERT Ů (30”) 27-15/16” (36”) 33-15/16” (42”) 39-15/16” (48”) 45-15/16” 4-15/16” (30”) 28-3/8” (36”) 34-3/8” (42”) 40-3/8” (48”) 46-3/8” (30”) 1-15/16” (36”, 42“, 48”) 4-15/16” 14-7/16” 11-1/4” 1-1/4” 3-1/16” 6-1/8” ” /4 3 4- FRONT 18-1/16” SIDE 12 BACK 5/16” TOP 3-3/4” 6-15/16” 1-15/16” (30”) 1-3/8” (36”, 42“, 48”) 4-3/8” Monsoon Mini II Use, Care, and Installation Guide
Installation Instructions ZEPHYRONLINE.COM Electrical Supply WARNING Electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards. Turn off electrical power at service entrance before wiring. For personal safety, remove house fuse or open circuit breaker before beginning installation. Do not use extension cord or adapter plug with this appliance. Follow national electrical codes or prevailing local codes and ordinances.
CORE Installation Instructions MONSOON MINI II INSERT Mounting the Hood CAUTION At least two installers are required due to the weight and size of the hood. 1. Remove all packing materials and protective film prior to installation. Use caution during installation to prevent scratches or damage to the stainless steel. 2. Cut out an opening in the bottom of the cabinet by following the dimensions in FIG. B.
Installation Instructions ZEPHYRONLINE.COM Mounting the Hood 4. Lift hood into bottom opening of cabinet and secure to interior of cabinet using (12) #8 x 1/2” stainless steel screws; (4) screws in the front and (4) screws in the sides and (4) screws in the back. FIG. D. 5. Finalize installation of electrical and duct work. Seal duct work with certified aluminum duct tape. Power on hood, check for leaks around duct tape and verify proper operation.
CORE Installation Instructions MONSOON MINI II INSERT Ducting Preparation If vertically ducting hood with 7” round collar or if using hood in recirculating mode, skip these steps and turn to the next page. Vertical Ducting (3-1/4"x10" Rectangular) 1. Remove 7" round transition collar on top of hood by (6) M4 x 6 screws. 2. Secure 3-1/4" x 10" rectangular collar to top of hood using (6) M4 x 6 screws. 1.
Installation Instructions ZEPHYRONLINE.COM Ductless Recirculation Ductless recirculation is intended for applications where an exhaust duct work is not possible to be installed. When converted, the hood functions as a recirculating hood rather than an exhaust hood. Fumes and exhaust from cooking are drawn and filtered by a set of optional charcoal filters. The air is then purified and re-circulated back within the home.
CORE Features & Controls MONSOON MINI II INSERT Electronic Touch Controls ś Űħ ħ 1 ħ Ű / 1 2 3 Ŝ 1 ħ Ű / Ě Ű Ĭ Ęĭ / Ě Ű Ę Ĭ ė Ű Ŝ Ę / Ŝ
Maintenance ZEPHYRONLINE.COM Hood & Filter Cleaning Surface Maintenance Ź Do not use corrosive detergents, abrasive detergents or oven cleaners. Ź Do not use any product containing chlorine bleach or any product containing chloride. Ź Do not use steel wool or abrasive scrubbing pads which will scratch and damage surface. Cleaning Stainless Steel Clean periodically with warm soapy water and clean cotton cloth or micro fiber cloth. Always rub in the direction of the stainless steel grain.
CORE Maintenance MONSOON MINI II INSERT Ų Ĭ Ę ĭė 1. Pull the filter latch while pivoting the filter downwards from the hood. 2. Remove the filter from the hood. FIG. F Ų Hood Model AK95 AK9546AS Part Number 50210041 50210041 Qty. to Order 2 3 To order parts, visit us online at http://store.zephyronline.com. LumiLight LED In the unlikely event that your LumiLight LED fails, please contact Zephyr to order replacement parts.
ACT™ Conversion ZEPHYRONLINE.COM ů Ĭ Ļĭ Some local codes limit the maximum amount of CFM a range hood can move. ACT™ allows you to control the maximum blower CFM of select Zephyr Ventilation range hoods without the need for expensive make up air kits. ACT™ enables the installer to easily set the maximum blower speed to one of two most commonly specified CFM levels, 390 or 290 CFM. The usage of ACT™ may not be necessary for your installation.
CORE ACT™ Conversion MONSOON MINI II INSERT Enabling ACT™ To enable ACT™: 1. Before hood installation, gain access to PC board by removing filters, side panels (if applicable), and light panel. 2. Change plastic jumper positioning as shown in FIG. H to set the desired maximum blower CFM. 3. Re-install PC board and continue with hood installation. 4.
Wiring Diagram ZEPHYRONLINE.
CORE Troubleshooting MONSOON MINI II INSERT Possible Problem After installation, the unit doesn’t work. Light works, but blower is not turning. Possible Cause Solutions The power source is not turned ON. Make sure the circuit breaker and the unit’s power is ON. The power line and the cable locking connector is not connecting properly. The switch board wirings are disconnected. The switch board is defective. Check the power connection with the unit is connected properly.
Troubleshooting ZEPHYRONLINE.COM Possible Problem The hood is not venting out properly. Filter is vibrating. Possible Cause Solutions Using the wrong size of ducting. Change the ducting to the correct size. The hood might be hanging to high from the cook top. Adjust the distance between the cook top and the bottom of the hood within 24” and 36” range. Close all the windows and doors to eliminate the outside wind flow.
CORE List of Parts & Accessories MONSOON MINI II INSERT Description Replacement Parts LumiLight LED, 6W Hybrid Baffle Filter (each) Part Number Z0B0047 50210041 Optional Accessories Recirculating Kit Replacement Charcoal Filter 7” Round Damper ZRC-9100A Z0F-C091 AK00067 To order parts, visit us online at http://store.zephyronline.com.
Limited Warranty ZEPHYRONLINE.COM y TO OBTAIN SERVICE UNDER WARRANTY OR FOR ANY SERVICE RELATED QUESTIONS United States Customers please call: 1-888-880-8368 or contact us at: zephyronline.com/contact Canada Customers please call: 1-800-361-0799 or Email: service@distinctive-online.
CORE Product Registration MONSOON MINI II INSERT Congratulations on the purchase of your Zephyr product! Please take a moment to register your new Zephyr product at www.zephyronline.com/registration IT’S IMPORTANT Prompt registration helps in more ways than one. Ensures warranty coverage should you need service. Ownership verification for insurance purposes. Notification of product changes or recalls. Zephyr Ventilation | 2277 Harbor Bay Pkwy. | Alameda, CA 94502 | 1.888.880.
WWW.ZEPHYRONLINE.COM Monsoon Mini II AK9528AS, AK9534AS, AK9540AS, AK9546AS EN Use, Care, and Installation Guide FR Guide d’utilisation, d’entretien et d’installation C TM Airflow Control Technology MAY21.
CORE MONSOON MINI II INSÉRER 2 Monsoon Mini II Guide d’utilisation, d’entretien et d’installation
Table des matières ZEPHYRONLINE.COM Page Consignes de sécurité ....................................................................... 4-6 Types d’avertissements de sécurité ..................................................... 4 Sécurité générale...............................................................................4-5 Opération ........................................................................................... 6 Exigences électriques .......................................................
CORE Consignes de sécurité MONSOON MINI II INSÉRER LISEZ ET CONSERVEZ CES INSTRUCTIONS Votre sécurité et celle des gens qui vous entourent sont très importantes. Ce manuel contient de nombreux messages de sécurité relatifs à votre appareil. Lisez tous les messages et conformez-vous-y en tout temps.
Consignes de sécurité ZEPHYRONLINE.
CORE Consignes de sécurité MONSOON MINI II INSÉRER LISEZ ET CONSERVEZ CES INSTRUCTIONS Opération Ź Laissez toujours les grilles de sécurité et les filtres en place. Sans ces composants, les soufflantes en fonctionnement pourraient s’accrocher aux cheveux, aux doigts et aux vêtements amples. Ź Le fabricant décline toute responsabilité en cas de non-respect des instructions données ici pour l’installation, la maintenance et l’utilisation appropriée du produit.
Liste de matériel ZEPHYRONLINE.
CORE Instructions d’installation MONSOON MINI II INSÉRER Feuille de calcul pour le conduit d’aération Longueur x Nombre utilisé Pièces de conduit = 1 pi x( ) = pi 6”, 7”, 8”, 10” 1 pi circ., droit x( ) = pi 3-1/ 4” x 10” rect., coude à 90º 15 pi x( ) = pi 3-1/ 4” x 10” rect., coude à 45º 9 pi x( ) = pi 6” circ. à rect. de 3-1/4" x 10" pi 16 pi 6” circ. à rect. de 3-1/4" x 10", coude à 90º pi 7” circ. à rect. de 3-1/4" x 10" 3-1/ 4” x 10” rect., droit 3-1/ 4” x 10” rect.
Instructions d’installation ZEPHYRONLINE.COM Hauteur de montage, dégagement et gaine n..
CORE Instructions d’installation MONSOON MINI II INSÉRER Hauteur de montage, dégagement et gaine Un conduit d’au moins 7 po rond ou 3-1/4 po x 10 po rectangulaire doit être utilisé pour maintenir une efficacité maximale du flux d’air. Utilisez toujours uniquement des conduits métalliques de type rigide. Les conduits flexibles peuvent restreindre le débit d’air jusqu’à 50%.
Instructions d’installation ZEPHYRONLINE.COM Options de conduits ATTENTION Risque d’incendie: NE JAMAIS évacuer l’air ni terminer de conduits dans des espaces entre les murs, les vides sanitaires, les plafonds, les greniers ou les garages. Tout l’échappement doit être canalisé vers l’extérieur, à moins d’utiliser l’option de recirculation. Ź Utilisez uniquement des conduits métalliques rigides à paroi simple.
CORE Instructions d’installation MONSOON MINI II INSÉRER ¯ Ů 1-15/16 po 4-15/16 po (30 po) 28-3/8 po (36 po) 34-3/8 po (42 po) 40-3/8 po (48 po) 46-3/8 po (30 po) 1-15/16 po (36 po, 42 po, 48 po) 4-15/16 po 1-1/4 po 14-7/16 po 3-1/16 po 4- po 6-1/8 po 4 3/ FACE 11-1/4 po 18-1/16 po CÔTÉ 12 ARRIÈRE 5/16 po HAUT 3-3/4 po 6-15/16 po (30 po) 27-15/16 po (36 po) 33-15/16 po (42 po) 39-15/16 po (48 po) 45-15/16 po (30 po) 1-3/8 po (36 po, 42 po, 48 po) 4-3/8 po Mons
Instructions d’installation ZEPHYRONLINE.COM Fourniture électrique ATTENTION Le câblage électrique doit être effectué par des personnes qualifiées conformément à tous les codes et normes applicables. Cette hotte doit être correctement mise à la terre. Coupez l’alimentation électrique à l’entrée de service avant le câblage. Pour votre sécurité personnelle, retirez le fusible de la maison ou ouvrez le disjoncteur avant de commencer l’installation.
CORE Instructions d’installation MONSOON MINI II INSÉRER Montage de la hotte ATTENTION Au moins deux installateurs sont nécessaires en raison du poids et de la taille de la hotte. 1. Retirez tous les matériaux d’emballage et le film protecteur avant l’installation. Soyez prudent lors de l’installation pour éviter les rayures ou les dommages à l’acier inoxydable. d éc A 28 K952 ou -1/ 2 p 8, A pe o, K95 34 -1/ 34, r 2p A o, K95 40 -1/ 40, 2p A o, K95 46 -1/ 48 2p o 3.
Instructions d’installation ZEPHYRONLINE.COM Montage de la hotte 4. Soulevez la doublure dans l’ouverture inférieure de l’armoire et fixez-la à l’intérieur de l’armoire à l’aide de (12) vis en acier inoxydable n ° 8 x 1/2 po; (4) vis à l’avant et (4) vis sur les côtés et (4) vis à l’arrière. FIG. D. 5. Finaliser l’installation des travaux d’électricité et de conduits. Sceller les conduits avec du ruban adhésif en aluminium certifié.
CORE Instructions d’installation MONSOON MINI II INSÉRER Préparation des conduits Si vous utilisez une hotte à conduit vertical avec un col rond de 7 po ou si vous utilisez une hotte en mode de recirculation, ignorez ces étapes et passez à la page suivante. Conduit vertical (Rectangulaire 3-1/4 po x 10 po) 1. Retirez le collier de transition rond de 7 po sur le dessus de la hotte à l'aide de (6) vis M4 x 6. 2.
Instructions d’installation ZEPHYRONLINE.COM Recirculation sans conduit La recirculation sans conduit est destinée aux applications où un conduit d’évacuation ne peut pas être installé. Une fois convertie, la hotte fonctionne comme une hotte à recirculation plutôt que comme une hotte aspirante. Les fumées et les gaz d’échappement de la cuisson sont aspirés et filtrés par un ensemble de filtres à charbon en option. L’air est ensuite purifié et recyclé dans la maison.
CORE Fonctionnalités et commandes MONSOON MINI II INSÉRER Commandes tactiles électroniques 2 µ ĩ ² ħ ħ 0¯ 1 ĩ ² £ / 1 2 3 3 Indicateurs de vitesse 1 Touche de mise en marche et arrêt à retardement / - La touche / vous permet d’allumer et d’éteindre la hotte (ventilateurs et lumières) - La hotte garde en mémoire la dernière vitesse et la dernière intensité d’éclairage utilisées.
Entretien ZEPHYRONLINE.COM Ů Entretien de surface Ź N’utilisez pas de détergents corrosifs, de détergents abrasifs ou de nettoyants pour four. Ź N’utilisez aucun produit contenant un agent de blanchiment chloré ou un produit contenant du chlorure. Ź N’utilisez pas de laine d’acier ou de tampons à récurer abrasifs qui pourraient rayer et endommager la surface.
CORE Entretien MONSOON MINI II INSÉRER Ů ¯ů Ĭ Ę ĭė 1. Tirez le loquet du filtre tout en faisant pivoter le filtre vers le bas depuis la hotte. 2. Retirez le filtre de la hotte. FIG. F Ů £ Modèle de capot AK95 AK9546AS Numéro d’article 50210041 50210041 Qté. commander 2 3 Pour commander des pièces, visitez-nous en ligne à http://store.zephyronline.com.
Conversion ACT™ ZEPHYRONLINE.COM Technologie de contrôle du débit d’air (ACT™) Certains codes locaux limitent la quantité maximale de CFM qu’une hotte de cuisinière peut déplacer. ACT™ vous permet de contrôler le CFM maximum du ventilateur de certaines hottes de cuisinière Zephyr Ventilation sans avoir besoin de kits d’air d’appoint coûteux. ACT™ permet à l’installateur de régler facilement la vitesse maximale du ventilateur à l’un des deux niveaux de CFM les plus couramment spécifiés, 390 ou 290 CFM.
CORE Conversion ACT™ MONSOON MINI II INSÉRER Activer ACT™ Pour activer ACT™: 1. Avant l’installation de la hotte, accédez à la carte de circuits imprimés en abaissant le panneau PAS et en retirant les filtres. 2. Changez le positionnement du cavalier en plastique comme illustré à la FIG. K pour régler le CFM maximum souhaité du ventilateur. 3. Réinstallez la carte de circuit imprimé et poursuivez l’installation de la hotte. 4.
Schéma de câblage ZEPHYRONLINE.
CORE Dépannage MONSOON MINI II INSÉRER Problème possible Après l'installation, l'appareil ne fonctionne pas. La lumière fonctionne, mais le ventilateur ne tourne pas. L'unité vibre. L'unité siffle. Le ventilateur fonctionne, mais les LED LumiLight ne le sont pas. 24 Cause possible Solutions La source d'alimentation n'est pas allumée. Assurez-vous que le disjoncteur et l’appareil sont sous tension.
Dépannage ZEPHYRONLINE.COM Problème possible La hotte ne s'échappe pas correctement. Cause possible Utilisation de la mauvaise taille de conduit. Changer le conduit à la bonne taille. La hotte est peut-être suspendue trop haut de la table de cuisson. Ajustez la distance entre la plaque de cuisson et le bas de la hotte dans les limites de 24 po et 36 po. Fermez toutes les fenêtres et portes pour éliminer le vent extérieur.
CORE Liste des pièces et accessoires MONSOON MINI II INSÉRER La description Pièces de rechange LumiLight LED, 6 W Filtre à chicane hybride (chacun) Numéro d’article Z0B0047 50210041 Accessoires optionnels Kit de recirculation Filtre à charbon de rechange Amortisseur rond de 7 po ZRC-9100A Z0F-C091 AK00067 Pour commander des pièces, visitez-nous en ligne à http://store.zephyronline.com.
Garantie limitée ZEPHYRONLINE.COM POUR OBTENIR UN SERVICE SOUS GARANTIE OU POUR TOUTE QUESTIONS LIÉES AU SERVICE Les clients des États-Unis doivent appeler le: 1-888-880-8368 ou nous contacter à: zephyronline.com/contact Clients du Canada, veuillez appeler: 1-800-361-0799 ou par courriel: service@distinctive-online.
CORE Enregistrement du produit MONSOON MINI II INSÉRER Nous vous félicitons d’avoir acheté une produit Zephyr. Veuillez prendre un moment pour enregistrer votre nouvelle produit au www.zephyronline.com/registration C’EST IMPORTANT Cet enregistrement rapide est utile à bien des égards. Il assure la couverture de votre garantie si vous avez besoin de service après-vente. À des fins d’assurance, il permet de confirmer que vous êtes le propriétaire.