JAN06.
E page 2 F page 24 S page 47 APPROVED FOR RESIDENTIAL APPLIANCES FOR RESIDENTIAL USE ONLY READ AND SAVE THESE INSTRUCTIONS PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING. INSTALLATION MUST COMPLY WITH ALL LOCAL CODES. IMPORTANT: Save these Instructions for the Local Electrical Inspectors use. INSTALLER: Please leave these Instructions with this unit for the owner. OWNER: Please retain these instructions for future reference.
Important safety Notice ..................................................................... 4 Electrical & Installation requirements ............................................. 5 Electrical requirements .............................................................. 5 Before installing the hood ........................................................... 5 List of Materials ................................................................................. 6 Parts supplied: .................................
Important safety Notice READ AND SAVE THESE INSTRUCTIONS CAUTION: FOR GENERAL VENTILATING USE ONLY. DO NOT USE TO EXHAUST HAZARDOUS OR EXPLOSIVE MATERIALS OR VAPORS. WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: A. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer. B.
ELECTRICAL REQUIREMENTS Important: Observe all governing codes and ordinances. It is the customers responsibility: To contact a qualified electrical installer. To assure that the electrical installation is adequate and in conformance with National Electrical Code, ANSI/NFPA 70 latest edition*, or CSA Standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No.0-M91 - latest edition** and all local codes and ordinances.
List of Materials PARTS SUPPLIED: Blower unit housing Hood canopy Metal filter x 1 Halogen light bulb x 2 Duct covers Remote Control Duct Cover support bracket (3 pieces to assemble) Hardware Packet: 4x8 screws x 4 (to assemble Duct cover support bracket) 6x70 screws x 2 (to fix Duct Cover support bracket) 10x60 wall anchors x 2 (Duct Cover support bracket) 5 x 45 screws x 3 (2 to fix Lower support bracket + 1 for securing hood) 9,5x3,5 screws x 6 (to fix hood canopy to blower unit housing
11" 5/8 max 45" 11/16 min 32" 13/16 max 51" 15/16 * min 36" * 6" 5/8 19" 5/8 16" 5/16 1/2" ceiling 11" 11" 12" 13/16 2"min 8" 7/16* Ducting and conduit area passage(Duct bends are not considered) 11" 1/2 21" 1/8 12" 13/16 Side Cabinet Side Cabinet 35" 6/16 35" 7/16 min. cabinets opening widths 24" to 32" bottom of canopy to cooking surface * Ductless (recirculating) version ONLY Note: if necessary order the proper duct cover extension kit. 7 CenterLine Dimensions and clearances www.
Installation Instructions Closely follow the instructions set out in this manual. All responsibility, for any eventual inconveniences, damages or fires caused by not complying with the instructions in this manual, is declined. VENTING METHODS The hood is equipped with a transition B for discharge of fumes to the outside (Ducting version). Should it not be possible to discharge cooking fumes and vapour to the outside, the hood can be used in the Ductless (recirculating) version.
Duct pieces Equivalent number lenght x used = Duct pieces Total Equivalent number lenght x used = Total 3 1/4 x 10 Rect., straight 1 Ft. x( )= Ft. 6" Round wall cap with damper 30 Ft. x ( )= Ft. 6 Round,, straight 1 Ft. x( )= Ft. 6 Round, roof cap 30 Ft. x ( )= Ft. 7", 8 Round,, straight 1 Ft. x( )= Ft. 6 Round to 3 1/4 x 10 rect. transition 1 Ft. x( )= Ft. 3 1/4 x 10 Rect.90° elbow 15 Ft. x ( )= Ft. 16 Ft. x ( )= Ft. 3 1/4 x 10 Rect.45° elbow 9 Ft.
Installation Assembling the duct cover support bracket (3 parts): 4. Tape template, matching center-line and hood bottom as shown in Figure below. The three parts should be fixed with 4 screws, the support extension is adjustable and should correspond to the internal width of the upper duct cover. 5. Place the lower support bracket on the template making it coincide with the traced triangle, mark center of two fastener location and one lower fastener location then remove template.
14. If supplied dismounted for shipping, assemble the lower part of the hood with the integral ventilator housing: a. Remove the grease filter (see also Care & Use section - Charcoal filter). b. Rest the integral ventilator housing on a flat surface and thread completely the lower part of the hood onto it. 10. Determine the required height for the conduit and cut a 1-1/4" (3.2 cm) hole at this location.
Installation 17. Secure hood with 1 screw on bottom. d. Fasten the hood to the motor unit using 6 screws from the bottom (release the grease filter to access fixing points. Duct cover support bracket Lower support bracket 15. Hang hood with the 2 mounting hooks. Hooks WARNING Excessive Weight Hazard - Use two or more people to move and install range hood. Failure to do so can result in back or other injury. 16.
19. Electrical connection Conduit WARNING Electrical Shock Hazard Warning: Turn off power circuit at the service panel before wiring this unit. 120 VAC, 15 or 20 Amp circuit required. J-Box cover ELECTRICAL GROUNDING INSTRUCTIONS THIS APPLIANCE IS FITTED WITH AN ELECTRICAL JUNCTION BOX WITH 3 WIRES, ONE OF WHICH (GREEN/YELLOW) SERVES TO GROUND THE APPLIANCE.
Installation 22. Install duct cover with 2 screws first on duct cover support bracket, then slide the duct lower section towards the bottom. Duct cover support bracket 23. Fit control ball with its molex plug on its housing and twist in place. TOP VIEW a Duct cover support bracket b Plate from electronic box ° c Upper duct cover 15 Lower duct cover Control Ball Housing Control Ball OK! 24. Perform connection between plates from control ball and from electronic box.
www.zephyronline.com Control panel Grease filter Grease filter release handle Halogen lamp (position and nr.
Description of the hood - Control Ball CONTROLS Use the high suction speed in cases of concentrated kitchen vapours. It is recommended that the cooker hood suction is switched on for 5 minutes prior to cooking and to leave in operation during cooking and for another 15 minutes approximately after terminating cooking. Description of control ball and hood operation The control ball is also a light signal: No signal : The hood is switched off.
USING THE REMOTE CONTROL This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The remote control may operate in humid environments, but not when placed on wet surfaces.
Maintenance Prior to any maintenance operation ensure that the cooker hood is disconnected from the power supply. CLEANING The cooker hood should be cleaned regularly internally and externally. For cleaning use a cloth moistened with a neutral liquid detergents. Avoid abrasive detergents. Warning: Failure to carry out the basic standards of the cleaning of the cooker hood and replacement of the filters may cause fire risks. Therefore we recommend oserving these instructions.
Issue After installation, the unit doesnt work? Cause What to do 1. The power source is not turned ON. 1. Make sure the circuit breaker and the units power is ON. 2. The power line and the cable locking connector is not connecting properly. 2. Check the power connection with the unit is connected properly. 3. The switch board and control board wirings are disconnected. 3. Make sure the wirings between the switch board and control board are connected properly. 4.
Warranty TO OBTAIN SERVICE UNDER WARRANTY: or any Service Related Questions, please call: 1-888-880-8368 Staple your receipt here. Proof of the original purchase date is needed to obtain service under the warranty. TO OBTAIN SERVICE UNDER WARRANTY: You must present proof of original purchase date. Please keep a copy of your dated proof of purchase (sales slip) in order to obtain service under warranty.
Part Description Part# halogen bulb, 12V 20 W Z0B-0009 metal filter GF02IA remote control (RF) 2009C remote control battery ..394 of 1.5V. (4 needed) Part Description Part# Ductless Recirculating Kit ZRC-00SA charcoal replacement filter Z0F-C060 duct cover extension kit Z1C-00SL internal blower - 600 cfm EBI-600A in-line blower - 1100 cfm EBN-1100A 21 List of Parts and Accessories www.zephyronline.
www.zephyronline.
