Use, Care, and Installation Guide www.zephyronline.com Ombra ZOM-E30ABS ZOM-E36ABS Model number: Serial Number: FEB18.0101 © Zephyr Ventilation LLC.
www.zephyronline.
INSTALLATION Ducting Calculation Sheet ....................................... Mounting Height & Clearance................................ Ducting Options ........................................................... +RRG 6SHFL¿FDWLRQV ................................................... Mounting the Range Hood ...................................... Ductless Recirculating .............................................. 5 6 7 8 9 10 FEATURES & CONTROLS Capacitive Touch Controls ................................
www.zephyronline.com Important Safety Notice READ AND SAVE THESE INSTRUCTIONS WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THIS FAN WITH ANY SOLID-STATE CONTROL DEVICE. WARNING TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: a. Use this unit only in the manner intended by the manufacturer, if you have questions, contact the manufacturer. b.
TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK. CAUTION 7R UHGXFH ULVN RI ¿UH DQG WR SURSHUO\ H[KDXVW DLU RXWVLGH 'R QRW YHQW H[KDXVW DLU LQWR VSDFHV ZLWKLQ ZDOOV FHLOLQJV attics, crawl spaces or garages. OPERATION $OZD\V OHDYH VDIHW\ JULOOHV DQG ¿OWHUV LQ SODFH :LWKRXW WKHVH FRPSRQHQWV RSHUDWLQJ EORZHUV FRXOG FDWFK RQWR KDLU ¿QJHUV and loose clothing.
www.zephyronline.
Duct pieces Total 1 Ft. x( ) = Ft. 6”, 7”, 8”, 10” 1 Ft. Round, straight x( ) = Ft. 3-1/ 4” x 10” Rect. 90 0 elbow 15 Ft. x( ) = Ft. 3-1/ 4” x 10” Rect. 45 0 elbow 9 Ft. x( ) = 3-1/ 4” x 10” Rect., straight Equivalent number length x used = Total 3-1/ 4” x 10” 5 Ft. Rect. to 6” round transition x( ) = Ft. 3-1/ 4” x 10” 20 Ft. Rect. to 6” round transition 90 0 elbow x( ) = Ft. 6” round to 1 Ft. 3-1/ 4” x 10” rect. transition x( ) = Ft. Ft. x( ) = Ft. 24 Ft. x( ) = Ft.
Installation – Mounting Height & Clearance www.zephyronline.com ALWAYS, when possible, reduce the number of transitions and turns. If a long duct run is required, increase duct size from 6” to 7”. If turns or transitions are required: Install as far away from opening and as far apart, between 2, as possible. A n. mi . B n mi . C x ma D n. mi . E n i m .F x ma Minimum mount height between range top to hood bottom should be no less than 26”. in. ” m x.
NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or garages. All exhaust must be ducted to the outside, unless using the recirculating option. Use single wall rigid Metal ductwork only.
8 3/4” 6 7/8” Standard min. ducted - 27 1/2” min. recirc - 32” max. 42 1/2” 29 7/8”, 35 7/8” Z1C-01OMBS min. ducted - 46 1/2” min. recirc. - 50 1/2” max. 80” 1 9/16” 12” Installation – +RRG 6SHFL¿FDWLRQV www.zephyronline.
1. Measure from range top to hood bottom and mark line A. ´ PLQLPXP IURP UDQJH WRS C/L Duct Cover Bracket 2. Plum and mark center line. 0DUN PRXQWLQJ KHLJKW OLQH % ´ IURP OLQH $ 3-1/2" 2" 4. Mark mounting spread from C/L on line B. From C/L to left PRXQW PDUN ´ )URP & / WR ULJKW PRXQW PDUN ´ )DVWHQ 0 [ ´ VFUHZV LQWR VWXGV RQ OLQH % 'R QRW fasten screws all the way. Note: wood blocking may need to be added behind the drywall if no studs are present.
Installation – Ductless Recirculating www.zephyronline.com Ductless recirculating is intended for applications where an exhaust duct work is not possible to be installed. When converted, the hood functions as a recirculating hood rather than an exhaust hood. Fumes and exhaust IURP FRRNLQJ DUH GUDZQ DQG ¿OWHUHG E\ D VHW RI RSWLRQDO FKDUFRDO ¿OWHUV 7KH DLU LV WKHQ SXUL¿HG DQG UH circulated back within the home.
6 Speed Indicators 1 Power / Delay Off 4 Lights On/Off 8 Lights Indicator Q 2 3 4 clean filters 3 Fan Speed Increase 7 Clean Filter Indicator Fan Speed Decrease 1 Power / Delay Off Button Button will turn power on and off for entire hood (fan and lights. - Hood will remember the last speed and light level it was last turned off at. (Example: Press button to turn off hood when on fan speed 3 and high lights. Press button again and the hood will turn back on at speed 3 and high lights.
Maintenance – Cleaning, Filter Care, Lights, Parts List www.zephyronline.com SURFACE MAINTENANCE: Do not use corrosive detergents, abrasive detergents or oven cleaners. Do not use any product containing chlorine bleach or any product containing chloride. Do not use steel wool or abrasive scrubbing pads which will scratch and damage surface. Cleaning Black Stainless Steel &OHDQ SHULRGLFDOO\ ZLWK ZDUP VRDS\ ZDWHU DQG FOHDQ FRWWRQ FORWK RU PLFUR ¿EHU FORWK 7R UHPRYH KHDYLHU grease build up use a liquid degr
Issue Cause What to do After installation, the unit doesn’t work. 1. The power source is not turned ON. 1. Make sure the circuit breaker and the unit’s power is ON. 2. The power line and the cable locking connector is not connecting properly. 2. Check the power connection with the unit is connected properly. 3. The wires on the control board are loose. 3. Make sure the wires on the control board are connected properly. 4. The switch board and control board wirings are disconnected. 4.
ACT Conversion www.zephyronline.com ALUÀRZ &RQWURO 7HFKQRORJ\ $&7 Some local codes limit the maximum amount of CFM a range hood can move. ACT allows you to control the maximum blower CFM of select Zephyr Ventilation range hoods without the need for expensive make up air kits. $&7 HQDEOHV WKH LQVWDOOHU WR HDVLO\ VHW WKH PD[LPXP EORZHU VSHHG WR RQH RI WZR PRVW FRPPRQO\ VSHFL¿HG &)0 OHYHOV RU &)0 7KH XVDJH RI $&7 PD\ QRW EH QHFHVVDU\ IRU \RXU LQVWDOODWLRQ 3OHDVH FKHFN \RXU ORFDO codes for CFM r
3.3 ŘʼnŊŕņ œņŅ œņŅ ńłőijĮij ŚņōōıŘ ŚņōōıŘ ńłőIJĮIJ ŚņōōıŘ ŃœŐŘŏ ŃōŖņ Ňłŏġʼn ŃōŖņ ōłŎő łńĮō ŚņōōıŘ ŚņōōıŘ ňœņņŏ ŘʼnŊŕņ ŃōłńŌ ŘʼnŊŕņ łńĮŏ ŃōłńŌ œņŅ ňœņŚ Ňłŏġō ŃōłńŌ ŇłŏġŎ ŃœŐŘŏ ňœņŚ ŘʼnŊŕņ łńIJijıŗ 3RZHU FRQVXPSWLRQ VKRZQ IRU GHIDXOW &)0 EORZHU FRQ¿JXUDWLRQ ACT 390 CFM - Fan Max. @ 2.5A ACT 290 CFM - Fan Max. @ 2.
Warranty www.zephyronline.
PRODUCT REGISTRATION Congratulations on your Zephyr range hood purchase! Please take a moment to register your new range hood at www.zephyronline.com/registration IT’S IMPORTANT Prompt registration helps in more ways than one. Ensures warranty coverage should you need service. Ownership verification for insurance purposes. Notification of product changes or recalls. Zephyr Ventilation | 2277 Harbor Bay Pkwy. | 17 Alameda, CA 94502 | 1.888.880.
Guide d’utilisation, d’entretien et d’installation www.zephyronline.com Ombra ZOM-E30ABS ZOM-E36ABS Model number: Serial Number: FEB18.0101 © Zephyr Ventilation LLC.
www.zephyronline.
2-3 4 INSTALLATION Feuille de calcul pour le conduit............................................................................... Espace libre et hauteur de montage........................................................................... Options d’installation pour le conduit................................................................................... 6SpFL¿FDWLRQV GH OD KRWWH ......................... Montage de la hotte..............
www.zephyronline.com Mise en garde de sécurité LISEZ ET CONSERVEZ CES INSTRUCTIONS AVERTISSEMENT POUR RÉDUIRE LES RISQUES D’INCENDIE OU DE DÉCHARGE ÉLECTRIQUE, N’UTILISEZ PAS CET APPAREIL AVEC UN TABLEAU DE COMMANDE À SEMI-CONDUCTEURS. AVERTISSEMENT POUR RÉDUIRE LES RISQUES D’INCENDIE, DE DÉCHARGE ÉLECTRIQUE OU DE BLESSURE, RESPECTEZ CES CONSIGNES : a. N’utilisez cet appareil que de la manière prévue par le fabricant. Si vous avez des questions, communiquez avec le fabricant. b.
POUR RÉDUIRE LES RISQUES D’INCENDIE, N’UTILISEZ QUE DES CONDUITS D’AÉRATION EN MÉTAL. ATTENTION Pour réduire les risques d’incendie et pour évacuer l’air convenablement, assurez-vous de canaliser l’air à l’extérieur de la maison. N’installez pas l’échappement du conduit dans les espaces entre les murs, le plafond, le grenier, les vides sanitaires ou le garage.
www.zephyronline.
= Longueur x Nombre utilisé Pièces de conduit Total 1 pi x( ) = pi 6”, 7”, 8”, 10” 1 pi circ., droit x( ) = pi 3-1/ 4” x 10” rect., coude à 90º 15 pi x( ) = pi 3-1/ 4” x 10” rect., coude à 45º 9 pi x( ) = pi 6” circ. à rect. de 3-1/4" x 10" 3-1/ 4” x 10” rect., droit ) = pi x( ) = pi x( ) = pi x( ) = pi x( ) = pi 23 pi 7” circ. à rect. de 3-1/4" x 10", coude à 90º x( ) = pi 3-1/ 4” x 10” 30 pi embout mural rect.
Installation – Espace libre et hauteur de montage www.zephyronline.com Lorsqu’il possible de le faire, diminuez TOUJOURS le nombre de pièces et de changements de direction. Si un long tronçon de conduit est nécessaire, augmentez le diamètre du conduit de 6” à 7”. A n. mi . B n i m .C x ma D n. mi . E n i m .F x ma Si des changements de direction ou des adaptateurs sont nécessaires, installez-les le plus loin possible de l’ouverture et le plus éloigné possible l’un de l’autre.
N’évacuez ou ne terminez JAMAIS l’échappement du conduit dans les espaces entre les murs, les vides sanitaires, le plafond, le grenier, ou le garage. Tous les échappements doivent être dirigés à l’extérieur de la maison, à moins que l’option de recirculation d’air ne soit utilisée. N’utilisez que des conduits en métal pour cloison simple.
8 3/4” 6 7/8” Standard min. ducted - 27 1/2” min. recirc - 32” max. 42 1/2” Z1C-01OMBS min. ducted - 46 1/2” min. recirc. - 50 1/2” max. 80” 1 9/16” 12” ,QVWDOODWLRQ ± 6SpFL¿FDWLRQV GH OD KRWWH www.zephyronline.
1. Prenez la mesure entre la surface de la cuisinière et la base de la hotte; marquez la ligne A (min. 26” à partir du dessus de la cuisinière). L/C Support puor le recouvrement du conduit 2. Marquez la ligne centrale avec exactitude. 3. Marquez la ligne de hauteur de montage B (à 12-1/4” de la ligne A). 3-1/2" 2" 4. Marquez la largeur de montage B à partir de la L/C 5. Fixez (2) vis M4 x 1-1/2” aux poutres de la ligne B. Ne tournez pas les vis jusqu’au fond.
,QVWDOODWLRQ ± 5HFLUFXODWLRQ G¶DLU VDQV FRQGXLW www.zephyronline.com /D FRQ¿JXUDWLRQ GH UHSULVH VDQV FRQGXLW D pWp FRQoXH SRXU OHV DSSOLFDWLRQV R LO HVW LPSRVVLEOH G¶LQVWDOOHU XQ FRQGXLW d’aération. Lorsque transformée, la hotte fonctionne comme une hotte de recirculation d’air plutôt que comme un V\VWqPH G¶pYDFXDWLRQ G¶DLU /HV YDSHXUV HW IXPpHV GH FXLVVRQ VRQW DVSLUpHV HW ¿OWUpHV SDU XQ HQVHPEOH RSWLRQQHO GH ¿OWUHV j FKDUERQ /¶DLU HVW HQVXLWH SXUL¿p HW UHGLULJp j O¶LQWpULHXU GH OD PDLVRQ Nous reco
Q 6 Indicateurs de vitesse 4 Lumières Allumer/Éteindre 8 Indicateur des lumières 2 3 4 clean filters 3 Augmentation de la vitesse du ventilateur 7 Indicateur de nettoyage des filtres Réduction de la vitesse du ventilateur 1 Mise en marche/Arrêt à retardement - La touche permet d’allumer et d’éteindre la hotte (le ventilateur et les lumières). - La hotte garde en mémoire la vitesse et l’intensité des lumières au moment de l’éteindre.
(QWUHWLHQ ± 'HV 6XUIDFHV 'HÀHFWHXUHV HW /XPLqUHV www.zephyronline.com ENTRETIEN DES SURFACES Nettoyez régulièrement les surfaces de la hotte avec de l’eau savonneuse chaude et un chiffon de coton propre. N’utilisez pas de détergent abrasif ou corrosif, de laines d’acier ou de tampons à récurer; ils égratigneront et endommageront les surfaces. Pour les taches plus tenaces, utilisez du produit dégraissant liquide.
3UREOqPH Cause 6ROXWLRQ Après l’installation, l’appareil ne fonctionne pas. 1. Le bloc d’alimentation n’est pas allumé 1. 2. La ligne électrique et le raccord de câble ne sont pas correctement branchés 9pUL¿H] TXH OH EUDQFKHPHQW GH O¶DSSDUHLO D pWp IDLW correctement Les lumières fonctionnent, mais le ventilateur ne tourne pas. L’appareil vibre. Assurez-vous que l’alimentation du disjoncteur et de l’appareil est allumée 3. Les câbles du tableau de commandes sont desserrés. 3.
&RQYHUVLRQ 'H /D $&7 www.zephyronline.com 7HFKQRORJLH GH FRQWU{OH GX GpELW G¶DLU $&7 Certains codes et règlements limitent la quantité maximale de pi3/min qu’une hotte peut extraire. La ACT permet de contrôler la quantité maximale de pi3/min qu’évacuent un éventail de hottes Zephyr, éliminant la nécessité d’acheter un dispositif d’air d’appoint dispendieux.
ZOM-E30ABS ZOM-E36ABS 3.3 SCHEMA DE CIRCUIT BLANC ROUGE ROUGE JAUNE BLEU NOIR BRUN GRIS BLANC JAUNE ńłőijĮij JAUNE Ňłŏġʼn BLEU ńłőIJĮIJ JAUNE Ňłŏġō GRIS ŇłŏġŎ BRUN łńĮŏ łńĮō VERT BLANC NOIR BLANC ōłŎő ROUGE JAUNE NOIR łńIJijıŗ &RQVRPPDWLRQ pQHUJpWLTXH DYHF FRQ¿JXUDWLRQ SDU GpIDXW G¶XQ YHQWLODWHXU GH SL3/min. ACT 390 pi3/min - Max. du ventilateur : à 2,5 A ACT 290 pi3/min - Max.
*DUDQWLH www.zephyronline.
ENREGISTRMENT DU PRODUIT Nous vous félicitons d’avoir acheté une hotte Zephyr. Veuillez prendre un moment pour enregistrer votre nouvelle hotte au www.zephyronline.com/registration C’EST IMPORTANT Cet enregistrement rapide est utile à bien des égards. Il assure la couverture de votre garantie si vous avez besoin de service après-vente. À des fins d’assurance, il permet de confirmer que vous êtes le propriétaire. Il vous permet de recevoir des avis concernant des modifications ou des rappels de produits.