2'×16' Metal Patio Wood Gazebo ASSEMBLY MANUAL MODEL#:LGMF1587 .
！ Use bolts to secure the frame to the ground to against the strong wind.
Wood Pole Beam Beam Beam Beam Corner Roof Bar Corner Roof Bar Connector Roof Bar Solidfying Bar Solidfying Bar Solidfying Bar Finishing Bar Finishing Bar Finishing Bar Finishing Bar Finishing Bar
Finishing Bar Finishing Bar Finishing Bar Finishing Bar Finishing Bar Roof Panel Roof Panel Roof Panel Roof Panel Roof Panel Roof Panel Roof Panel Roof Panel Roof Panel Roof Panel Roof Panel
Roof Panel Roof Panel Roof Panel Roof Panel Roof Panel Roof Panel Roof Panel Roof Panel Roof Panel Roof Panel Roof Panel Roof Panel Roof Panel Roof Panel Net Frame Net Frame
Net Frame Base Base Cover Joint Cover Joint Cover Union Bar Corner Solidifying Bar Corner Solidifying Bar Inside Roof Cover Outside Roof Cover J-Hook Bracket Joint Cover Bracket Hook Corner Cover Finishing End Mosquito Sidewall Plastic Bracket Plastic Bracket Plastic Bracket Bracket Bracket Spacer Bracket Finishing End Plastic Bracket Solid Sidewall Plastic Bracket
Drill
(1) Put Part #B on the bottom of Part #A, after adjusting the position, use Drill #16 to drill holes at the holes in Part #B. (2) Secure Part #B and Part #A with 4 Bolts #13. (3) Cover Part #B1 on Part #B. (4) Repeat the above procedures to assemble the other 3 Part #A.
(2) Insert the other side of Part #C2 into Part #C and secure with 3 Bolts #8. (1) Insert Part #C2 into Part #C1 and secure with 3 Bolts #8. (4) Insert Part #X into the beam and secure with 1 Bolt #8. (3) Connect Part #C1 and Part #C through Part #C2. (5) Secure the bottom of Part #X and Part #C/C1 with 3 Bolts #8. (6) Repeat the above procedures to assemble the other Part #C and Part #C1.
(2) Insert the other side of Part #C2 into Part #D1 and secure with 3 Bolts #8. (1) Insert Part #C2 into Part #D and secure with 3 Bolts #8. (4) Insert Part #X into the beam and secure with 1 Bolt #8. (3) Connect Part #D and Part #D1 through Part #C2. (5) Secure the bottom of Part #X and Part #D/D1 with 3 Bolts #8. (6) Repeat the above procedures to assemble the other Part #D and Part #D1.
(1) Connect Part #D/#C1 to Part #A with 2 Bolts #17, and fix from the other side with 2 Bolts #18.(The first row of screw holes) (2) Connect Part #C/#D1 to Part #A with 2 Bolts #17, and fix from the other side with 2 Bolts #18.(The second row of screw holes) (3) Secure Part #D&#C / #C1&D1 with 4 Bolts #14. (4) Repeat the above procedures to assemble the other corners.
(1) Affix Part #B2 and Part #B3 to the Beam with 4 Bolts #8. (2) Repeat the above procedures to assemble the other 3 corners. ！ Please don't tighten all bolts.
(1) Affix Part #R to Part #B3 with 2 Bolts #6, 2 Washers #15 and 2 Nuts #5. (2) Affix Part #R1 to Part #B2 with 2 Bolts #6, 2 Washers #15 and 2 Nuts #5. ！(3) Use Drill #16 to drill holes in the holes reserved for Part #R/#R1. (4) Affix Part #R and Part #R1 to the poles with 4 Bolts #13. (5) Repeat the above procedures to assemble the other 3 corners. ！ Tighten all the bolts.
(1)Put 4 Part #19 on the 4 holes. (4) Secure with 2 Self-tapping Screws #3. (from bottom to top) (2) Cover the corner with Part #X1. (3) Secure with 2 Self-tapping Screws #3. (from top to bottom) (5) Repeat the above procedures to assemble the other 3 corners.
(1) Connect Part #U to Part #A with 4 Bolts #4. (2) Repeat the above procedures to assemble the other 3 corners.
Assemble the 4 Corner Roof Bars: (1) Connect Part #E1 and Part #E with 2 Bolts #8 . (2) Repeat the above procedures to assemble the other 3 corner roof bars.
Please have a freestanding ladder ready at the center of the gazebo. (1) Place 4 Part #E1 on the 4 corners of Part #S. Secure with 8 Bolts #8 (from bottom to top) ATTENTION: You can also finish this step on the ground and then lift 4 corner roof bar and inside roof connector to the top together. (Need 2 people and 2 ladder) Outside View Inside View (2) Place 4 Part #E on 4 Part #A; Secure with 4 Part U and 8 Bolts #8.
(1) Attach Part #U1 to Part #E2 with Bolt #7 . (2) Repeat the above procedures to assemble the other 3 roof bars.
(1) Place Part #E2 on Part #S. Secure with Bolt #8 (from bottom to top). Outside View Inside View (2) Connect Part #E2 and the Assembled Beam(D&D1) with part #U1. Secure with 2 Bolts #8. (3) Repeat the above procedures to assemble the opposite side.
(1) Place Part #E2 on part #S. Secure with Bolt #8 (from bottom to top). Outside View Inside View (2) Connect Part #E2 and the Assembled Beam(C&C1) with part #U1. Secure with 2 Bolts #8 . (3) Repeat the above procedures to assemble the opposite side.
Secure Part #T to Part #S and Part #S1. (From Bottom to Top) ATTENTION: The holes of Part #S and Part #S1 need to be aligned, on the same vertical line.
Inside View (1) Insert Part #U3 into Part #G and Part #G1. (2) Attach Part #G and Part #G1 to the Part #E2 with 1 Bolt #7 and 2 Blots #8. (3) Repeat the above procedures to assemble the opposite side.
Inside View (1) Insert Part #U3 into 2 Part #F. (2) Attach Part #F to the Part #E2 with 1 Bolt #7 and 2 Blots #8. (3) Repeat the above procedures to assemble the opposite side.
Inside View (1) Insert Part #U2 into Part #F and Part #G1. (2) Secure with 2 Bolts #8. (3) Secure them to Part #E with Bolt #8. (4) Repeat the above procedures to assemble the opposite sides.
Inside View (1) Insert Part #U2 into Part #F and Part #G. (2) Secure with 2 Bolts #8. (3) Secure them to Part #E with Bolt #8. 24 (4) Repeat the above procedures to assemble the opposite sides.
(1) Connect Part #J1 and Part #Q1 with 2 Bolts #7 and 2 Nuts #5. (2) Connect Part #J2 and Part #Q2 with 2 Bolts #7 and 2 Nuts #5.
Inside View (1) Place the Assembled J1 & Q1 and J2 & Q2 on Part #E2, securing with 1 Bolt #8. 26 (2) Repeat the above procedures to assemble the opposite side.
(1) Connect Part #J and Part #Q with 2 Bolts #7 and 2 Nuts #5. (2) Place the Assembled Part #J & #Q on Part #E2, securing with 1 Bolt #8. 27 （3) Repeat the above procedures to assemble the opposite side.
(1) Place Part #J and Part #J1/J2 on Part #E; put on Part #X3 and secure with Self-tapping Screw #2. Inside View Inside View (2) Repeat the above procedures to assemble the other 3 corners.
Cover Part #Z, #Z1 & #Z2 to Roof Panels.
Cover Part #Z, #Z3 & #Z4 to Roof Panels.
ATTENTION: The bigger roof panel need to cover the smaller one. If you can’t install N2 or N3, push the outside roof cover up and try to insert them again. (1) Insert Part #N1 and Part #N2 into the frame. 31 (2) Insert Part #N4 and Part #N3 into the frame. (3) Repeat the above procedures to assemble the opposite side.
(1) Place Part #H1 and Part #H2 on Part #E2; put on Part #X2 and secure with Bolt #8. (2) Repeat the above procedures to assemble the opposite side.
ATTENTION: The bigger roof panel need to cover the smaller one. (1) Insert Part #L1 and Part #L2 into the frame. (2) Insert Part #L4 and Part #L3 into the frame. (3) Attach Part #H to Part #E2, securing with Bolt #8. 33 (4) Repeat the above procedures to assemble the opposite side.
(1) Place Part #H and Part #H2 on Part #E1; put on Part #X3 and secure with Self-tapping Screw #2 Outside View (2) Repeat the above procedures to assemble the other 3 corners.
Cover Part #Z to Roof Panels Section View 35
Cover Part #Z to Roof Panels 36
Cover Part #Z to Roof Panels 37
#9 #11 Part #W should be inserted between roof panels and solidifying bar or beams, then secure with bolts and nuts.
ATTENTION: The bigger roof panel need to cover the smaller one. 14 (1) Insert Part #P1, Part #P2 and Part #P3 into the frame. 14 (3) Place 1 Part #W between roof panels and solidifying bars. Then secure with 1 Bolt #12 and 1 Nut #5. 12 2 (2) Place 6 Part #W between roof panels and beams. Then secure with 6 Bolts #10 and 6 Nuts #5. 39 (4) Repeat the above procedures to assemble the opposite side.
ATTENTION: The bigger roof panel need to cover the smaller one. 18 (1) Insert Part #P9, Part #P8 and Part #P7 into the frame. 18 (3) Place 2 Part #W between roof panels and solidifying bars. Then secure with 2 Bolt #12 and 2 Nut #5. 14 4 (2) Place 7 Part #W between roof panels and beams. Then secure with 7 Bolts #10 and 7 Nuts #5. 40 (4) Repeat the above procedures to assemble the opposite side.
ATTENTION: The bigger roof panel need to cover the smaller one. (1) Insert Part #P4, Part #P5 and Part #P6 into the frame. (3) Place 6 Part #W between roof panels and solidifying bars. Then secure with 6 Bolts #12 and 6 Nuts #5. (2) Place 9 Part #W between roof panels and beams. Then secure with 9 Bolts #10 and 9 Nuts #5. 41 (4) Repeat the above procedures to assemble the opposite side.
(1) Place 2 Part #W between Part #P5 and Part #E2. Then secure with 2 Bolts #9 and 2 Nuts #5. (2) Repeat the above procedures to assemble the opposite side.
ATTENTION: The bigger roof panel need to cover the smaller one. (1) Insert Part #M1 and Part #M2 into the frame. 43 (2) Insert Part #M8 and Part #M7 into the frame. (3) Place 6 Part #W between roof panels and beams. Then secure with 6 Bolts #10 and 6 Nuts #5. (4) Repeat the above procedures to assemble the opposite side.
ATTENTION: The bigger roof panel need to cover the smaller one. (1) Insert Part #M3 into the frame. (3) Place 4 Part #W between roof panels and solidifying bars. Then secure with 4 Bolts #12 and 4 Nuts #5. (2) Insert Part #M6 into the frame. (4) Place 6 Part #W between roof panels and beams. Then secure with 6 Bolts #10 and 6 Nuts #5. 44 (5) Repeat the above procedures to assemble the opposite side.
ATTENTION: The bigger roof panel need to cover the smaller one. (1) Insert Part #M4 into the frame. (3) Place 4 Part #W between roof panels and solidifying bars. Then secure with 4 Bolts #12 and 4 Nuts #5; Place 1 Part #W between roof panels and Part #E2. Then secure with 1 Bolt #9 and 1 Nut #5. (2) Insert Part #M5 into the frame. 45 (4) Place 6 Part #W between roof panels and beams. Then secure with 6 Bolts #10 and 6 Nuts #5; Place 1 Part #W between roof panels and Part #E2.
(1) Place Part #W between roof panels and Part #E2. Then secure with Bolt #11 and Nut #5. (2) Repeat the above procedures to assemble the other 3 sides.
(1) Place Part #K2 and Part #K3 on Part #E2; Put on Part #X2 and secure with Bolt #8. (2) Repeat the above procedures to assemble the opposite side.
(1) Place Part #K and Part #K1 on Part #E2; Put on Part #X2 and secure with Bolt #8. (2) Repeat the above procedures to assemble the opposite side.
X3 (1) Place Part #K3 and Part #K on Part #E; Put on Part #X3 and secure with Self-tapping Screw #2. (2) Repeat the above procedures to assemble the other 3 corners.
(1) Attach roof panels to finishing bars with 2 Self-tapping Screws #3. (2) Repeat the above procedures to assemble the other 3 sides.
How to Put the 120 Hooks into the Double-track Double-track 8 Hooks × 2 Rows 7 Hooks × 2 Rows 7 Hooks × 2 Rows 8 Hooks × 2 Rows 8 Hooks × 2 Rows 7 Hooks × 2 Rows 8 Hooks × 2 Rows 7 Hooks × 2 Rows 51
(1) Place 7 hooks on each slot of the Sidewall Track(C1&C). (2) Install Part #T1 at the joint of Part C&C1 with Bolt #8. Double-track 52 (3) Repeat the above procedures to assemble the opposite side.
(1) Place 8 hooks on each slot of the Sidewall Track(D&D1). (2) Install Part #T1 at the joint of Part D&D1 with Bolt #8. Double-track 53 (3) Repeat the above procedures to assemble the opposite side.
Hang up Mosquito Sidewalls to Inside Track 54
Hang up Solid Sidewalls to Outside Track 55
