Instructions / Assembly

ManualsBrandsZevni ManualsLightingPlug-In/Hardwire Swing Arm Wall Light, 1-Light Modern Polished Brass Wall Sconce, Industrial Black Wall Sconce Lighting

service@zevni.com

Item Number: Z-87NQBYBV-4281

WARNING (To reduce the risk of fire, electric shock, or personal injury):

1. We s

uggest installation by a

licensed electrician

2. Please read the instruction carefully and save it as you may need it at a later time.

3. Before you start,

NEVER

attempt any work without shutting off the electricity until the work is done.

A) Go to the main fuse, or circuit breaker, box in your home.

Place the main power switch in the “

OFF

” position.

B) Place the wall switch in the “

OFF

” position.

4. Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides.

Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.

5. Make sure that the ceiling or wall can stand the weight of the lamp before installation.

6. Make sure the voltage you are using is

120V

. The maximum wattage is

60W

per bulb.

7. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.

8. When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs

get hot quickly.

9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may

occur. It must be understood that common sense, caution and care must be used with any electrical

products.

IMAGE FOR FINISHED PRODUCT:

Page:  1  / 6

CLEANING

To clean, wipe the fixture with a soft cloth. Do not use abrasive materials such as scouring pads or

powders, steel wool or abrasive paper.

ORDERING PARTS

Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture

can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering

parts.

Summary of content (6 pages)

PAGE 1
service@zevni.com Item Number: Z-87NQBYBV-4281 WARNING (To reduce the risk of fire, electric shock, or personal injury): 1. We suggest installation by a licensed electrician. 2. Please read the instruction carefully and save it as you may need it at a later time. 3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done. A) Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
PAGE 2
service@zevni.com TOOLS REQUIRED (NOT INCLUDED): Before starting assembly and installation please prepare the needed tools as below picture PARTS TYPE & QTY INCLUDING: (C) Mounting plate assembly (1) (D) Green ground screw (1) (E) Back plate (1) (F) Stud (3) (G) Joint (3) (H) Arm (2) (I) Socket (1) (J) Lampshade (1) (K) Socket ring (1) (L) Ball nut (2) ACCESSORIES & QTY ENCLOSED: (A) Plastic Wire Connector (3) (B) Mounting screw (2) ASSEMBLY & INSTALLATION INSTRUCTIONS: 1.
PAGE 3
service@zevni.com (a) For PLUG IN Installation: 3(a). Remove studs (F) from joints (G). 4(a). Carefully pull the wires and fiberglass sleeve from the other end of arm (H). Push socket (I) to put two parts of joint (G) together, then lay wires in the fluted side of joint (G). Put two parts of joint (G) together again, and secure them with stud (F). Do the same to the other two joints (G) as well. Adjust studs (F) and lock arms (H) together. 5(a).
PAGE 4
service@zevni.com 6(a). Attach mounting plate (C) to the outlet box on the wall using mounting screws (A). 7(a). Align the holes in back plate (E) with the pre assembled mounting screws, then attach back plate (E) using the previously removed ball nuts (L). Hand tighten until snug. Note: back plate (E) should be snug against the wall and ball nuts (L).
PAGE 5
service@zevni.com (b) For Hardwired Installation: 3(b). Remove studs (F) from joints (G). 4(b). Carefully pull the wires and fiberglass sleeve from the other end of arm (H). Push socket (I) to put two parts of joint (G) together, then lay wires in the fluted side of joint (G). Put two parts of joint (G) together again, and secure them with stud (F). Do the same to the other two joints (G) as well. Adjust studs (F) and lock arms (H) together. 5(b).
PAGE 6
service@zevni.com Connect ground wires according to the below chart Connect wires according to the below chart Twist wires together with plastic wire connectors until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box. 7(b). Align the holes in back plate (E) with the preassembled mounting screws, then attach back plate (E) using the previously removed ball nuts (L).