Quick Start Guide

T2XXXXXX
Video Doorbell
Quick Start Guide
V1.0.0
Foreword
General
This manual introduces the functions, installation and operations of the
camera.
Safety Instructions
The following categorized signal words with defined meaning might appear
in the Manual.
Signal Words Meaning
Indicates a medium or low potential hazard which, if
not avoided, could result in slight or moderate injury.
Indicates a potential risk which, if not avoided,
could result in property damage, data loss, lower
performance, or unpredictable result.
Provides additional information as the emphasis and
supplement to the text.
About the Manual
●
The manual is for reference only. If there is inconsistency between the
manual and the actual product, the actual product shall prevail.
●
We are not liable for any loss caused by the operations that do not comply
with the manual.
●
The manual would be updated according to the latest laws and
regulations of related regions. For detailed information, see the
paper manual, CD-ROM, QR code or our official website. If there is
inconsistency between paper manual and the electronic version, the
electronic version shall prevail.
●
All the designs and software are subject to change without prior written
notice. The product updates might cause some differences between the
actual product and the manual. Please contact the customer service for
the latest program and supplementary documentation.
●
There still might be deviation in technical data, functions and operations
description, or errors in print. If there is any doubt or dispute, please refer
to our final explanation.
●
Upgrade the reader software or try other mainstream reader software if
the manual (in PDF format) cannot be opened.
●
All trademarks, registered trademarks and the company names in the
manual are the properties of their respective owners.
●
Please visit our website, contact the supplier or customer service if there
is any problem occurred when using the device.
●
If there is any uncertainty or controversy, please refer to our final
explanation.
Important Safeguards and Warnings
Electrical Safety
●
All installation and operation shall conform to your local electrical safety
codes.
●
The power supply must conform to the requirements of ES1 in IEC
62368-1 standard and be no higher than PS2. Note that the power supply
requirements are subject to the device label.
●
Make sure that the power supply is correct before operating the device.
●
A readily accessible disconnecting device shall be incorporated in the
building installation wiring.
●
Prevent the power cable from being trampled or pressed, especially the
plug, power socket and the junction extruded from the device.
Environment
●
Do not aim the device at strong light to focus, such as lamp light and sun
light; otherwise it might cause over brightness or light marks, which are
not the device malfunction, and affect the longevity of Complementary
Metal-Oxide Semiconductor (CMOS).
●
Do not place the device in a damp, dusty extremely hot or cold
environment, or the locations with strong electromagnetic radiation or
unstable lighting.
●
Keep the device away from any liquid to avoid damage to the internal
components.
●
Keep the indoor device away from rain or damp to avoid fire or lightning.
●
Keep sound ventilation to avoid heat accumulation.
●
Transport, use and store the device within the range of allowed humidity
and temperature.
●
Heavy stress, violent vibration or water splash are not allowed during
transportation, storage and installation.
●
Pack the device with standard factory packaging or the equivalent
material when transporting the device.
●
Install the device in the location where only the professional staff with
relevant knowledge of safety guards and warnings can access. The
accidental injury might happen to the non-professionals who enter the
installation area when the device is operating normally.
Operation and Daily Maintenance
●
Do not touch the heat dissipation component of the device to avoid scald.
●
Carefully follow the instructions in the manual when performing any
disassembly operation about the device; otherwise, it might cause water
leakage or poor image quality due to unprofessional disassembly. Plea
se
contact after-sale service for desiccant replacement if there is condensed
fog on the lens after unpacking or when the desiccant turns green. (Not all
models are included with the desiccant).
●
It is recommended to use the device together with lightning arrester to
improve lightning protection effect.
●
It is recommended to ground the device to enhance reliability.
●
Do not touch the image sensor (CMOS) directly. Dust and dirt could be
removed with air blower, or you can wipe the lens gently with soft cloth
that is moistened with alcohol.
●
You can clean the device body with soft dry cloth, and for stubborn stains,
use the cloth with mild detergent. To avoid possible damage on device
body coating which could cause performance decrease, do not use
volatile solvent such as alcohol, benzene, diluent and so on to clean the
devi
ce body, nor can strong, abrasive detergent be used.
●
Dome cover is an optical component. Do not touch or wipe the cover with
your hands directly during installation or operation. For removing dust,
grease or fingerprints, wipe gently with moistened oil-free cotton with
diethyl or moisten soft cloth. You can also remove dust with an air blower.
●
Strengthen the protection of network, device data and personal
information by adopting measures which include but not limited to using
strong password, modifying password regularly, upgrading firmware to the
latest version, and isolating computer network. For some device with old
firmware versions, the ONVIF password will not be modified automatically
along with the modification of the system password, and you need to
upgrade the firmware or manually update the ONVIF password.
●
Use standard components or accessories provided by manufacturer and
make sure that the device is installed and maintained by professional
engineers.
●
The surface of the image sensor should not be exposed to laser beam
radiation in an environment where a laser beam device is used.
●
Do not provide two or more power supply sources for the device unless
otherwise specified. A failure to follow this instruction might cause
damage to the device.
1
Package Contents
Tools Required
Doorbell
×1
Mounting Bracket
×1
Angled Bracket ×1
(15° horizontally)
Angled Bracket ×1
(5° vertically)
Wall Anchors
×2
Chime Kit
×1
15/64" Drill Bit ×1
Drill
Wire Nuts
×3
Pin ×1
Philips-head
Screwdriver
Extension Wires
×2
Wire Harness
×2
Mounting Screws
×2
Micro SD card
(pre-inserted)
2
Overview
1
2
3
4
5
6
7
8
9
10
Table 2-1 Doorbell description
No. Name No. Name
1 Lens 6 Reset
2 Microphone 7 Micro SD card Slot
3 LED Indicator 8 Power Ports
4 Call Button 9 Night Light
5 Micro USB Port 10 Speaker
Table 2-2 Indicator light pattern
LED Status Device Status
Solid red Resetting to factory default
Solid blue
●
Starting/Restarting
●
Device online
Slowly flashing blue Enabling hotspot
Fast flashing blue Configuring network
Flashing red and blue Updating firmware
Slowly flashing red Wi-Fi connection failed
Spinning blue Call in progress for the doorbell
3
Operating With DMSS App
To ensure the best possible wireless performance, make sure that there are
no obstacles and electromagnetic interference between the device and the
router.
Step 1 Add the device.
1) Tap + button on the upper-right corner of the DMSS homepage
to scan the QR code on the camera. If your DMSS fails to scan
the QR code, tap Manually enter SN.
2) Tap Next once the indicator light on the device flashed a slow
blue light.
Step 2 Configure the device.
1) Connect the device hotspot labelled Doorbell-xxxxxxxx.
●
Enable GPS/Location for DMSS, otherwise the configuration
might fail.
●
If the app displays device hotspot directly, tap Join.
2) Initialize the video doorbell. Create a security password for the
device and then tap Next.
3) Select your Wi-Fi network from the SSID list and enter the
password.
4) Create a device name and then set the time zone.
5) (Optional) Select chime type and then tap Save.
If the doorbell is not connected to any chime, skip this
step.Otherwise the video doorbell might not work properly.
Step 3 Connect to the platform.