Bullet Network Camera Quick Start Guide ZHEJIANG DAHUA VISION TECHNOLOGY CO., LTD. V1.0.
Quick Start Guide Foreword General This manual introduces the functions, configuration, general operation, and system maintenance of network camera. Safety Instructions The following signal words might appear in the manual. Signal Words Meaning Indicates a medium or low potential hazard which, if not avoided, could result in slight or moderate injury. Indicates a potential risk which, if not avoided, could result in property damage, data loss, lower performance, or unpredictable result.
Quick Start Guide ● ● ● ● or errors in the print. If there is any doubt or dispute, we reserve the right of final explanation. Upgrade the reader software or try other mainstream reader software if the manual (in PDF format) cannot be opened. All trademarks, registered trademarks and the company names in the manual are the properties of their respective owners. Please visit our website, contact the supplier or customer service if any problems occur while using the device.
Quick Start Guide Important Safeguards and Warnings Electrical Safety ● All installation and operation shall conform to your local electrical safety codes. ● The power supply must conform to the requirements of ES1 in IEC 62368-1 standard and be no higher than PS2. Note that the power supply requirements are subject to the device label. ● Make sure that the power supply is correct before operating the device.
Quick Start Guide mild detergent. To avoid possible damage on device body coating which could cause performance decrease, do not use volatile solvent such as alcohol, benzene, diluent to clean the device body, nor can strong, abrasive detergent be used. ● Dome cover is an optical component. Do not touch or wipe the cover with your hands directly during installation or operation. For removing dust, grease or fingerprints, wipe gently with moistened oil-free cotton with diethyl or moistened soft cloth.
Quick Start Guide Table of Contents Foreword ..................................................................................................................................................I Important Safeguards and Warnings ...................................................................................................III 1 Introduction .........................................................................................................................................1 1.1 Cable .................
Quick Start Guide 1 Introduction 1.1 Cable Waterproof all the cable joints with insulating tape and waterproof tape to avoid short circuit and water damage. For the detailed operation, see FAQ manual. Figure 1-1 Cables Table 1-1 Cable information No. Port Name Description ● Connects to network with network cable. ● Provides power to the device with PoE. 1 Ethernet port PoE is available on select models. Inputs 12 VDC power. Be sure to supply power as instructed in the manual.
Quick Start Guide 2 Network Configuration Device initialization and IP setting can be finished with the ConfigTool or on web interface. For more information, see web operation manual. ● Device initialization is available on select models, and it is required at first-time use and after device is being reset. ● Device initialization is available only when the IP addresses of the device (192.168.1.108 by default) and the PC stay on the same network segment.
Quick Start Guide Step 5 Step 6 Step 7 system, update the device, restart the device, and more. Click OK. Select one or several devices in uninitialized status, and then click Initialize. Select the devices to be initialized, and then click Initialize. ● If you do not provide the linked information for password reset, you can reset the password only through XML file. ● When initializing multiple devices, ConfigTool initializes all devices based on the password reset mode of the first selected device.
Quick Start Guide Figure 2-3 Device initialization Step 9 Select Easy4ip or select Auto-check for updates according to the actual needs. If neither, leave them unselected. Step 10 Click OK to initialize the device. Click the success icon ( ) or the failure icon ( ) for the details. Step 11 Click Finish. 2.2 Changing Device IP Address ● You can change IP address of one or multiple devices at one time. This section is based on changing IP addresses in batches.
Quick Start Guide Figure 2-4 Modify IP address Step 3 Select Static mode, and then enter start IP, subnet mask, and gateway. Step 4 ● IP addresses of multiple devices will be set to the same if you select the Same IP checkbox. ● If DHCP server is available in the network, devices will automatically obtain IP addresses from DHCP server when you select DHCP. Click OK. 2.
Quick Start Guide 3 Operating with DMSS To ensure the best possible wireless performance, make sure that there are no obstacles and electromagnetic interference between the device and the router. Step 1 Add the device. 1) Tap + button on the upper-right corner of the DMSS home page to scan the QR code on the camera. If your DMSS fails to scan the QR code, tap Manually enter SN. 2) Choose Wireless Camera. Figure 3-1 Add the device Step 2 Configure the device hotspot.
Quick Start Guide Figure 3-2 Configure the device hotspot Step 3 Step 4 Configure the Wi-Fi. Select your Wi-Fi network from SSID list and enter the password. Configure the device information. 1) Create the device name and password. 2) Set the time zone and click Done.
Quick Start Guide 4 Installation 4.1 Packing List ● The tool required for the installation such as electric drill is not provided in the package. ● The operation manual and related tool information are contained in the disk or the QR code. Figure 4-1 Packing list 4.
Quick Start Guide 4.3 Installing Camera 4.3.1 Installation Method Figure 4-3 Installation method 4.3.2 Installing SD Card ● SD card slot is available on select models. ● Disconnect the power before installing or removing the SD card. ● Do not open the cover for a long time to avoid spray in cameras. Press the reset button for 10 seconds to reset the device. Figure 4-4 Install SD card 4.3.
Quick Start Guide Figure 4-5 Cable going through the side cable tray Figure 4-6 Cable going through the mounting surface 4.3.4 (Optional) Installing Waterproof Connector This part is needed only when a waterproof connector comes with the camera and the camera is used outdoors.
Quick Start Guide Figure 4-7 Install waterproof connector 4.3.
Quick Start Guide
