Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Dahua 2 Inch PTZ Dome Camera Web3.0 Operation Manual Version 1.0.0 Zhejiang Dahua Vision Technology CO.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Table of Contents 1 2 3 4 Network Config .............................................................................................................. 1 1.1 Network Connection.......................................................................................... 1 1.2 Log in ................................................................................................................ 1 Live ..........................................................
4.3 4.4 4.5 4.6 4.7 4.8 Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual 4.2.1 Global Setup ............................................................................................. 35 4.2.2 Scene Setup ............................................................................................. 36 4.2.3 Rule Setup ................................................................................................ 38 4.2.4 Parameter Setup.................................................................
5 6 Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual 4.8.3 Online User............................................................................................... 95 Alarm ........................................................................................................................... 96 Log out ........................................................................................................................
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Important The following functions are for reference only. Some series products may not support all the functions listed below.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual 1 Network Config 1.1 Network Connection Speed dome and PC connection mainly has two ways. See Figure 1-1 and Figure 1-2. Figure 1-1 Figure 1-2 Before you access speed dome via the Internet, you need to have its IP address. You can use quick config tool to search IP of the speed dome. Please refer to Quick Configuration Tool manual. 1.2 Log in Open IE and input speed dome address in the address bar. For example, if your speed dome IP is 192.168.1.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Input your IP address here Figure 1-3 The login interface is shown as below. See Figure 1-4. Please input your user name and password. Default factory username is admin and password is admin. Note: For security reasons, please modify your password after you first login.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual If it is your first time to login in, you may see the interface shown as in Figure 1-5. Figure 1-5 Click “Please click here to download and install the plug-in”. The system pops up warning information to ask you whether run or save this plug-in. Please download to your local computer and then click webplugin.exe; you can see an interface shown as in Figure 1-6.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Figure 1-6 Click install, you will see Figure 1-7. Figure 1-7 When plug-in installation is complete, the installation page closes automatically. The web-end will refresh automatically, and then you can view video captured by the camera.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual 2 Live After you logged in, you can see the live monitor window. See Figure 2-1. 2 1 3 4 Figure 2-1 There are four sections: Section 1: Encode setup bar Section 2: System menu Section 3: Window function option bar Section 4: Window adjust bar 2.1 Encode Setup The encode setup interface is shown as in Figure 2-2.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Figure 2-2 Please refer to the following sheet for detailed information. Parameter Function Main stream Streaming media protocol connection, under main stream config, monitor video or not. Generally for storage and monitor. Streaming media protocol connection, under sub stream 1 config, monitor video or not. When network bandwidth is insufficient, it substitutes main stream for monitoring.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual SN Parameter Function 1 Regional Focus 2 Remark 3 Zoom 4 Snapshot Click the button and use mouse to select an area in the box on the video screen, which will make the device auto focus in the selected box area. Click it and then select pen color, you can write down the mark information on the preview interface. When the video is in the original status, click it you can select any zone to zoom in.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Parameter Function Video setup It is to adjust monitor video brightness. It is to adjust monitor video contrastness. It is to adjust monitor video hue. Note: All the operations here apply to WEB end only. Please go to Setup>Camera->Conditions to adjust corresponding items. It is to adjust monitor video saturation. Reset Restore brightness, contrastness saturation and R hue to systemedefault setup. Figure 2-6 2.4.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual 2.4.6 Rule Info Click it to enable the function that the intelligent rule will be displayed in the live interface. The default is enable. 2.4.7 PTZ Click it to open PTZ setup interface. Please refer to chapter 2.5 for detailed setup information. 2.5 PTZ Configuration 2.5.1 PTZ Control Before PTZ operation, please make sure you have properly set PTZ protocol.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Figure 2-7 2.5.2 Virtual Joystick The virtual joystick interface is shown as below. See Figure 2-8. This function allows you to control the button in then center to simulate the joystick operation. You can use it to control device movement. Figure 2-8 2.5.3 PTZ Function Click PTZ set button, the interface is shown as in Figure 2-9. Here you can select scan, preset, tour pattern, assistant function and etc.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Figure 2-9 Please refer to the following sheet for PTZ setup information. Parameter Function Scan Select Scan from the dropdown list, click Start button, you can begin scan operation. Default SN is 1. Preset Tour Pattern Input the preset value and then click View button, the camera turns to the corresponding position of the preset. Select Tour from the dropdown list and then click Start button, you can begin tour.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual 3 Playback Web client playback supports video playback and picture playback. Note: Before playback, user shall set storage management as in Chapter 4.6. 3.1 Playback The playback interface is shown as in Figure 3-1.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual 3.1.1 Function of Play The function of play is shown as in Figure 3-2. Figure 3-2 Parameter Function ① Play When you see this button, it means pause or not played record. Click this button, switch to normal play status. ② Stop Click this button to stop playing. ③ Frame by frame play Click this button to go to next frame. Note: You shall pause record when you use this function. ④ Slow Click this button to play slowly.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Figure 3-3 Parameter File Type Data Source Function Select “dav”, as video playback. Select “jpg” as picture playback. Default is SD card. Step 1. Click data in blue, time axis displays record file progress bar in color. While, green represents normal record, yellow represents motion detect record, red represents alarm record, and blue represents manual record. Step 2. Step 3. Click certain time on progress bar, playback starts from this time.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Figure 3-5 Parameter Search Record Download Format Download Function It means records within searched start time and end time on the date. There are two formats: dav, mp4. Record type is “dav”, click download button to download file to local. Record type is “mp4”, click download button and download file to path in Ch 5.1.2.5. Note: System does not support download and playback of MP4 file. Back Click back button to go to calendar interface.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual 3.1.3 Playback Cut (Clip) Note: Playback cut function will automatically pause playing record as playback cut and playback cannot be at the same time. Step 1. Click start time to cut on time axis. This time must be within progress bar range. Step 2. Move mouse to cut icon . You will be ask to select start time. Click cut icon as finish cutting. Step 3. Click playback cut end time on time axis. This time must be within progress bar range. Step 4.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Parameter Function 24 hours Click it, means video in past 24 hours. 2 hours Click it, means video in past 2 hours. 1 hour Click it, means video in past 1 hour. 30 min Click it, means video in past 30 min. 3.1.6 Assistant Function Video playback assistant function is shown in Figure 3-9. Figure 3-9 Please refer to the following sheet for detailed information.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Figure 3-10 3.2.1 Play The play button is shown as below. See Figure 3-11. Figure 3-11 Default icon is , and it means pause or not played picture. Click play button to switch to normal play status. Icon becomes Click it to pause. . 3.2.2 Playback File Step 1: Click file list , select snapshot file of the date.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Step 2: Double click file in list to play this snapshot. Figure 3-12 Figure 3-13 Please refer to the following sheet for detailed information. Parameter Search Download Back Function It means all snapshot files within the start time and end time of selected date. Click download button to download snapshot file to local. Click back button to return to calendar interface and re-select time. 3.2.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual 4 Setup Web client setup support camera, network, PTZ, event, storage, system and system info view. 4.1 Camera 4.1.1 Conditions Here you can view device property information. Slight differences may be found due to different speed dome series. The setups become valid immediately after you set. See Figure 4-1. Figure 4-1 Please refer to the following sheet for detailed information. Parameter Function Config File Here you can set camera setup mode.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Zoom& Focus It is to set camera zoom and focus mode. It is to set digital zoom/camera zoom rate. Focus mode includes: auto/manual/semi auto. Picture It is to set camera video. It includes: style/hue/brightness/saturation/ chroma control/gamma/picture flip/picture freeze/sharpness /sharpness control It is to set the defog mode for the picture, including “Off” and “Auto”. It is to restore factory default setup.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Exposure interface is shown as below. See Figure 4-3. Figure 4-3 Please refer to the following sheet for detailed information. Parameter Function Exposure mode Anti-flicker It is to set camera exposure mode. It includes: auto and manual. The default setup is auto. For the auto exposure mode, the gain, shutter and iris are in auto mode. For manual exposure mode, the gain, shutter and iris are in manual mode.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Slow exposure Max Auto gain Slow shutter Auto Slow Shutter Min value 2D NR 3D NR If the light may change greatly, you can use slow exposure to get image so that the camera can get stable video. It is to set camera max gain. In lower illumination environment, you can lower the cameras auto exposure time to capture the image and enhance the definition. For the moving object, the trail may appear. Please note it is valid in auto mode.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual HLC BLC When there is strong light source in the environment, system can auto adjust video brightness to remove the over exposure effect. For the environments of strong contrast effect, such as under the backlight environment, system can auto adjust image contrast to get clear object. 4.1.1.4 Day/Night Important Please make sure your purchased product camera supports this function. The day/night mode is shown as in Figure 4-5.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Figure 4-6 Please refer to the following sheet for detailed information. Parameter Function Digital zoom Check the box here to enable digital zoom function. Zoom speed It is to set camera zoom speed. The bigger the value is, the faster the speed is. Focus mode It is to set camera focus mode. It includes: auto/manual/semi auto. It is to camera focus distance in case the focus distance is too small and the focus goes to the enclosure.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Figure 4-7 Please refer to the following sheet for detailed information. Parameter Function Style It is to set video style. It includes:Standard/soft/ flamboyant. Hue It is to set picture hue. Brightness Saturation Chroma control It is to set video brightness. The higher is value is, the bright the video is. It is to set color purity. The higher the purity is, the more color the video is. The lower the purity is, the dark the video is.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Figure 4-8 Parameter Note Mode It is to set the camera defog mode, it includes: off and auto. 4.1.1.8 Default Default interface is shown as in Figure 4-9. Figure 4-9 Please refer to the following sheet for detailed information.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Parameter Function Default It is to restore camera parameter to factory default setup. 4.1.1.9 Profile Management Profile management interface is shown as in Figure 4-10. Figure 4-10 Please refer to the following sheet for detailed information. Parameter Function Profile Management There are three modes: normal/full-time/schedule. The default setup is normal. Normal It is to adopt the general parameter on the profile file.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Figure 4-11 Please refer to the following sheet for detailed information. Parameter Function Sub Stream Enable Please check the box here to enable extra stream function. This function is enabled by default. ACF means using different fps to record. There are two options: VBR and CBR. Please note, you can set video quality in VBR mode. There are three options: H.264, H.264B, H.264H and MJPEG encode. H.264: Main Profile encode mode. H.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Parameter Function Bit Rate Type There are two options: VBR and CBR. Please note, you can set video quality in VBR mode. Under MJPEG mode, only CBR is available. Recommended Bit Recommended bit rate value according to the resolution and frame rate you have set. Bit Rate In CBR, the bit rate here is the max value. In dynamic video, system needs to low frame rate or video quality to guarantee the value. The value is null in VBR mode.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Image size It is the same with the resolution of snapshot (main stream or sub stream). Quality It is to set the image quality. There are six levels. Interval It is to set snapshot frequency. The value ranges from 1s to 7s. 4.1.2.3 Video Overlay The video overlay interface is shown as in Figure 4-13 to Figure 4-17.
Dahua 2 Inch PTZ Camera Web 3.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Figure 4-17 Please refer to the following sheet for detailed information. Parameter Function Privacy Masking Channel Title Time Title OSD Select “privacy mask zone”, click “draw”, drag mouse on the video monitoring window and draw the corresponding privacy shielded zone of “privacy mask zone”. Select “privacy mask zone”, click “delete” to delete the corresponding privacy shielded zone of “privacy mask zone”.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Picture Overlay Refresh You can enable this function to display overlay picture. Click disable to turn it off. See Figure 4-. Click Upload Picture to overlay local picture into monitoring window. You can drag the yellow box to move it. Note: You cannot enable OSD and overlay at the same time. Set channel title, time title, OSD info, picture overlay and save the change. You can click Refresh to see effect. 4.1.2.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual The default monitor record path is C:\Documents and Settings\Administrator\WebDownload\LiveRecord. The default playback snapshot path is C:\Documents and Settings\Administrator\WebDownload\PlayBackPicture. The default playback download path is C:\Documents and Settings\Administrator\WebDownload\PlayBackRecord. The default playback cut path is: C:\Documents and Settings\Administrator\WebDownload\PlayBackRecordCut.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Parameter Note IVS Enable Check it to enable IVS function. Apply Scene It can select normal scene and face detect, normal scene by default. Scene Type It is divided into single scene and multi-scene: Single scene: It realizes IVS to signel scene. Multi-scene: It realizes IVS to several scenes, tour switch between scenes. 4.2.2 Scene Setup Figure 4-21 Parameter Note Add Scene Click Zoom PTZ Speed Click to add scene.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Figure 4-22 Single scene: Enter “Single Scene” page, click the button to select the scene which needs to be monitored. Note: It needs to select the “Single Scene” from “IVS Setup > Global Setup > Scene Type” .
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Multi-scene: Enter “Multi-scene” page, click to add tour scene, move the mouse to the location of “Scene Name”, select scene, move the mouse to “Stay Time” to set the stay time of the current scene. Note: It needs to select “Multi-scene” in the “IVS Setup > Global Setup > Scene Type”. 4.2.3 Rule Setup Figure 4-24 Parameter Note Select Scene You can select the scene from the dropdown list so that you can add the corresponding rule.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Parameter Note Rule Type Move your mouse to the “Rule Type” column to set the rule type. The option includes: Tripwire/Intrusion/Object abandoned/Missing object detection and etc. Draw Rule Click button to draw current rule. Delete Rule Click button to delete the selected rule. 4.2.3.1 Tripwire Figure 4-25 Parameter Note Direction It is to select tripwire direction. The option includes: A->B、B->A、A<->B.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Figure 4-26 Parameter Detect list Function In area: When the tracking object is in the detect zone and the stay time is more than the time threshold you set here, system can activate an alarm. Through area: System can generate an alarm when the tracking object is crossing the limit you set here. action Direction Max target No. Min target No. Min last time Report interval It is for the Through area option in the Detect action list item.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Parameter Function Check the box here to enable this function and then click button Target filter set the target filter model in this scene. Click the button selected target filter model. ,you can ,you can remove 4.2.3.3 Abandoned Figure 4-27 Parameter Function Min last time It is to set the min time between the abandoned object occurrence and alarm activation.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Figure 4-28 Parameter Function Min last time It is to set the min time between the missing object occurrence and alarm activation. Check the box here to enable this function and then click button Target filter set the target filter model in this scene. Click the button selected target filter model. ,you can ,you can remove 4.2.3.
Dahua 2 Inch PTZ Camera Web 3.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Parameter Rule Period Record Function Working It is to set rule working period, click ‘Setup” button to open period setup menu to set. Check the box here so that the device can record when alarm activation occurred. Check the box here so that the device can send out an email to inform user when alarm activation occurred. Send Email Note: Please note current function is null when the device is offline, or IP conflict Snapshot Copy occurs.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Parameter Function Scene Please select corresponding scene to set parameter. Detect balance There are three modes: compromise mode, omission detect less and error detect less. Sensitivity The level ranges from 1 to 10. The default setup is 5. The higher the sensitivity is, the easier for the device to detect the low contrast object and small object. At the same time, the error detect may become more.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Parameter Function Host Name It is to set current host device name. It max supports 15 characters. Ethernet Card Please select the Ethernet port. Default is wired. Please note you can modify the default Ethernet card if there is more than one card. . Please note the device needs to reboot to activate the new setup once you modify the default setup. Mode There are two modes: static mode and the DHCP mode.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Enable ARP/Ping set device IP address service. You can use ARP/Ping command to modify or set the device IP address if you know the device MAC address. Before the operation, please make sure the speed dome and the PC in the same LAN. This function is on by default. You can refer to the steps listed below. Step 1: Get an IP address. Set the speed dome and the PC in the same LAN. Step 2: Get the physical address from the label of the speed dome.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Figure 4-33 4.3.3 Connection 4.3.3.1 Connection The connection interface is shown as in Figure 4-34. Figure 4-34 Please refer to the following sheet for detailed information.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Parameter Function Max connection It is the max Web connection for the same device. The value ranges from 1 to 20. Default connection amount is 10. TCP port Port range is 1025~65534. The default value is 37777. You can input the actual port number if necessary. UDP port Port range is 1025~65534. The default value is 37778. You can input the actual port number if necessary. HTTP port Port range is 1025~65524. The default value is 80.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Figure 4-35 Please refer to the following sheet for detailed information. Parameter Function Authentication The login authentication is off by default. 4.3.4 PPPoE The PPPoE interface is shown as in Figure 4-36. Input the PPPoE user name and password you get from the IPS (internet service provider) and enable PPPoE function. Please save current setup and then reboot the device to get the setup activated.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Figure 4-36 4.3.5 DDNS The DDNS interface is shown as in Figure 4-37. The DDNS is to set to connect the various servers so that you can access the system via the server. Please go to the corresponding service website to apply a domain name and then access the system via the domain. It works even your IP address has changed. When the device connects to WLAN, you should disable UPnP.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Figure 4-37 Please refer to the following sheet for detailed information. Parameter Function Server Type You can select DDNS protocol from the dropdown list: CN99 DDNS, NO-IP DDNS, Dyndns DDNS, and Dahua DDNS. The Dahua DDNS protocol means you use your self-defined private protocol to realize DDNS function. Server Address DDNS server IP address Domain Name Your self-defined domain name. Username The user name you input to log in the server.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Parameter Function Server Type You can select DDNS protocol from the dropdown list and then enable DDNS function. The Dahua DDNS means you use your self-defined private protocol to realize DDNS function. Server Address DDNS server IP address. Under DDNS the default server address is www.dahuaddns.com Mode The default is auto, and you can select manual. Domain Name Auto and self-defined domain names are both MAC address.quickddns.com.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual 4.3.7 SMTP (e-mail) The SMTP interface is shown as in Figure 4-40. Figure 4-40 Please refer to the following sheet for detailed information. Parameter Function SMTP Server Input server address and then enable this function. Port Default value is 25. You can modify it if necessary. Anonymity For the server supports the anonymity function. You can auto login anonymously. You do not need to input the user name, password and the sender information.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Parameter Function Attachment System can send out the email of the snapshot picture once you check the box here. Mail receiver Input receiver email address here. Max three addresses. Interval The send interval ranges from 0 to 3600 seconds. 0 means there is no interval. Please note system will not send out the email immediately when the alarm occurs.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Figure 4-41 4.3.9 SNMP The SNMP interface is shown as in Figure 4-42. The SNMP allows the communication between the network management work station software and the proxy of the managed device. Please install the software such as MG MibBrowser 8.0c software or establish the SNMP service before you use this function. You need to reboot the device to activate the new setup.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Figure 4-42 Please refer to the following sheet for detailed information. Parameter Function SNMP Version Check SNMP v1, device only process v1 info. Check SNMP v2, device only process v2 info. Check SNMP v3, can set username, password and encryption method. Server calibrate corresponding username, password and encryption method too access device and v1/v2 are unavailable. SNMP port The listening port of the proxy program of the device.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Parameter Function Trap Address Address where to send Trap message. Port which send Trap message, default is 162, range 1~65535. Check SNMP v3 version and SNMP port, read community, write community, Trap address, Trap port are same with SNMP v1 and SNMP v2 versions. Only when SNMP version is SNMP v3, user need to configure parameter in chart. See Figure 4-43. Trap Port Figure 4-43 Please refer to the following sheet for detailed information.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Parameter Function Authentication Password Password not less than 8 characters. Encryption Default is CBC-DES. Encryption Password Password not less than 8 characters. 4.3.10 Bonjour The Bonjour interface is shown as below. See Figure 4-44. Bonjour is based on the multicast DNS service from the Apple. The Bonjour device can automatically broadcast its service information and listen to the service information from other device.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual can just send out one data to transit. This function also depends on the relationship of the group member and group of the outer. Note: Open preview, streaming media protocol, select multicast, and monitor via multicast format. Here you can set multicast address and port. You also need to go to Live interface to set the protocol as Multicast. Figure 4-45 Please refer to the following sheet for detailed information.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Figure 4-46 Parameter Note Enable Check “Enable” to enable WIFI function. Add SSID After it is enables, click “Add SSID”, add network ID in the dialog box, then it needs to click “Search SSID” to confirm if the network ID is available. It means the network ID is available if it can search the hotspot of the wireless network.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual 4.3.13 802.1x 802.1x (port based network access control protocol) supports manual selection of authentication method to control if device connected to LAN can join the LAN. It well supports authentication, charging, safety and management requirement of network. See Figure 4-47. Figure 4-47 Please refer to the following sheet for detailed information. Parameter Function Authentication PEAP (protected EAP protocol).
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual We can set the DSCP (Differentiated Services Code Point) of the IP to distinguish the data packet so that the router or the hub can provide different services for various data packets. It can select the different queues according to the priority (64 different priority levels) of the packets and select the bandwidth of the each queue. Level 0 is the lowest, and level 63 is the highest. It can also discard at the different ratio when the broad bandwidth is jam.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Figure 4-49 In this part, you can operate the PTZ of the camera and control PTZ movement. Parameter Function Preset Set camera preset. Tour Set camera tour. Max 8 tours. Scan Set camera scan. Pattern Set camera pattern. PTZ speed Set PTZ movement speed. Idle motion Set camera idle operation. Power up Set camera operation when system boots up. Time Task Set camera time task. PTZ restart Restart camera PTZ.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual 4.4.1.1 Preset Preset interface is shown as in Figure 4-50. Figure 4-50 Please refer to the following sheet for detailed information. Parameter Function Preset No. Set preset No. It becomes valid after you set. Preset title Set preset name. You can input self-defined preset name here. Delete Delete corresponding preset. Save Save current preset setup. Add Click it to add a new preset. Clear Clear all presets setup. 4.4.1.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Figure 4-51 Please refer to the following sheet for detailed information. Parameter Function Tour No. System auto allocates. Tour title Set tour name. You can input self-defined tour name here. Start Begin tour. Please note this function is null if you have not set a tour. Stop Stop tour Please note this function is null if you have not set a tour Add Click it to add a new tour. Preset Click Add button, you can add a new tour.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual 4.4.1.3 Scan Scan interface is shown as below. See Figure 4-52. Figure 4-52 Please refer to the following sheet for detailed information. Parameter Function Scan No. System auto allocates. Speed Set scan speed here. You cannot set speed when camera is running scan. Start Begin scan. Please note this function is null if you have not set a scan.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Figure 4-53 Please refer to the following sheet for detailed information. Parameter Function Pattern No. System auto allocates. Start Stop Begin pattern. Please note this function is null if you have not set a pattern. Stop pattern Please note this function is null if you have not set a pattern Set Click it you can see start/stop record buttons. Start record Click it to begin recording pattern setup.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Figure 4-54 Please refer to the following sheet for detailed information. Parameter Function PTZ speed Here you can set camera PTZ speed. 4.4.1.6 Idle Motion Idle motion interface is shown as below. See Figure 4-55.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Please refer to the following sheet for detailed information. Parameter Function Enable Check the box here to enable idle motion function. Idle Motion Here you can set preset, scan, pattern, tour. Please note you need to set the corresponding operation first if you want to use this function. Idle time Set idle time. 4.4.1.7 Power up Power up interface is shown as below. See Figure 4-56.
Dahua 2 Inch PTZ Camera Web 3.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Parameter Note Enable It is to enable time task function. Task Action It is to set the time task action, such as preset, tour, scan and pattern. Auto Home When call PTZ artificially and interrupt time task, it can auto restore the time that time task needs. Period Setting It is to set the exact period of time task, click “setting” to set. Copy to Task No Click “Copy” to copy the well-set task information to the designated task number. 4.4.1.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Figure 4-60 Please refer to the following sheet for detailed information. Parameter Function Default Restore PTZ factory default setup. 4.5 Event 4.5.1 Video detect 4.5.1.1 Motion Detect The motion detect interface is shown as in Figure 4-61 through Figure 4-64.
Dahua 2 Inch PTZ Camera Web 3.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Figure 4-64 Please refer to the following sheet for detailed information. Parameter Function Enable You need to check the box to enable motion detection function. Working Period Here you can set arm/disarm period. Click set button to open period setup menu. See Figure 4-. There are six periods every day for setup and you must check box in front of each period to enable it. Note: Period setup can be done by dragging mouse while not release left mouse.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Parameter Function If you enabled this function, System can send out email to alert you when alarm occurs and ends. User can set email address in Network>SMTP. Here you can set PTZ movement when alarm occurs. Such PTZ as go to preset x when there is an alarm. The event type includes: preset, tour and pattern. You need to check the box here so that system can backup motion Snapshot detection snapshot file.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Device without SD card function does not have the above three statuses. Figure 4-65 Figure 4-66 Figure 4-67 Please refer to the following sheet for detailed information. Parameter Function Event Type There are three kinds of events for SD card abnormality alarm: No SD card, Capacity Warning, SD card error.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Parameter Function Enable Check to alarm when SD card is abnormal. Send email After you enabled this function, the system can send out email to alarm the specified user. This function is invalid when network is offline or IP conflict occurs. SD Card Capacity Limit User can set SD card capacity that is left free. When SD card space left is smaller than this limit, alarm occurs.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Figure 4-70 4.6 Storage Management 4.6.1 Schedule Before schedule setup, user must set record mode is auto or manual. Note: If record mode in record control is off, then device will not snapshoot according to schedule. 4.6.1.1 Record Schedule Record schedule steps: Step 1. Click Record Schedule, see Figure 4-71. Figure 4-71 Step 2. From Monday to Sunday select record time, click setup on the right. See Figure 4-72. Set period according to actual need.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Note: Period setup can be done by dragging in record schedule interface while not releasing left mouse. Figure 4-72 Step 3. Click OK, return to record schedule interface. See Figure 4-73. Green color stands for the general record/snapshot. Yellow color stands for the motion detect record/snapshot. Red color stands for the alarm record/snapshot. Figure 4-73 Step 4. In record schedule interface, click OK. System prompts it is successfully saved. 4.6.1.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Step 1. Click Snapshot Schedule tab, see Figure 4-74. Figure 4-74 Step 2. From Monday to Sunday select snapshot time, click setup on the right. See Figure 4-75. Set snapshot period according to actual need. There are six periods available each day. By checking or cancel, user can add or delete three types of snapshot schedule: General, Motion and Alarm.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Red color stands for the alarm record/snapshot. Figure 4-76 Step 5. In snapshot interface, click OK. System prompts it is successfully saved. 4.6.1.3 Holiday Schedule Holiday schedule can set specific date as holiday. Step 1. Click Holiday Schedule tab. See Figure 4-77. Figure 4-77 Step 2. Select date to set as holiday. The selected date will be highlighted in yellow. Step 3. Check Record/Snapshot, click Save. System prompts it is successfully saved.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual 4.6.2 Destination 4.6.2.1 Path The destination interface is shown as in Figure 4-78. Path can config record and snapshot storage path. There are three options: Local, FTP and NAS. You can only select one mode. System can save according to the event types. It is corresponding to the three modes (general/motion/alarm) in the Schedule interface. Please check the box to enable the save functions. Note: Only device supports SD card has local.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Figure 4-79 4.6.2.3 FTP The FTP interface is shown as in Figure 4-80. You need to check the box to enable the FTP function. When network disconnect occurred or there is malfunction. Emergency storage can save the record/snapshot picture to the local SD card. Figure 4-80 4.6.2.4 NAS You need to check the box to enable the NAS function. Select NAS storage as to same file to NAS disk. See Figure 4-81.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Figure 4-81 4.6.3 Record control The record control interface is shown as in Figure 4-82. Figure 4-82 Please refer to the following sheet for detailed information. Parameter Function Pack Duration Here you can select file size within 1min~120min. Default setup is 8 minutes. Pre-record Please input pre-record value here. For example, system can record the four seconds video in the buffer. The record begins from the fifth second.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Disk Full Record mode Record stream There are two options: stop recording or overwrite the previous files when HDD is full. Stop: Current working HDD is overwriting or current HDD is full, it will stop record. Overwrite: Current working HDD is full; it will overwrite the previous file. There are three modes: Auto/manual/close. There are two options: main stream and sub stream. 4.7 System 4.7.1 General The General interface is shown as in Figure 4-83.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Figure 4-84 Please refer to the following sheet for detailed information. Parameter Function Date format Here you can select date format from the dropdown list. Time Format There are two options: 24-H and 12-H. Time zone The time zone of the device. System time It is to set system time. It becomes valid after you set. Sync PC You can click this button to save the system time as your PC current time.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual For the character in the following user name or the user group name, system max supports 15digits. The valid string includes: character, number, and underline. Password can be 0~32 characters in number and letter only. User can modify other user’s password. The user amount is 18 and the group amount is 8 when the device is shipped out of the factory. The factory default setup includes two levels: user and admin.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Figure 4-86 Modify user It is to modify the user property, belonging group, password and rights. See Figure 4-87. Modify password It is to modify the user password. You need to input the old password and then input the new password twice to confirm the new setup. Please click the OK button to save. Please note, the password ranges from 0-digit to 32-digit. It shall include the number and letter only.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Figure 4-87 4.7.2.2 Group The group management interface can add/remove group, modify group password and etc. The interface is shown as in Figure 4-88. Figure 4-88 Add group: It is to add group and set its corresponding rights. See Figure 4-89.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Please input the group name and then check the box to select the corresponding rights. It includes: preview, playback, record control, PTZ control and etc. Figure 4-89 Modify group Click the modify group button, you can see an interface is shown as in Figure 4-90. Here you can modify group information such as remarks and rights. Figure 4-90 4.7.3 Default The default setup interface is shown as in Figure 4-91.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Figure 4-91 4.7.4 Import/Export The interface is shown as in Figure 4-92. Figure 4-92 Please refer to the following sheet for detailed information. Parameter Function Import It is to import the local setup files to the system. Export It is to export the corresponding system setup to your local PC. 4.7.5 Auto Maintenance The auto maintenance interface is shown as in Figure 4-93.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual If you want to use the auto delete old files function, you need to set the file period. Figure 4-93 Parameter Function Auto Reboot Check it and set auto reboot time. Auto Delete Old Files Check it and set period within 1~31 days. 4.7.6 Upgrade The upgrade interface is shown as in Figure 4-94. Please select the upgrade file (file extension is “.bin”) and then click the update button to begin firmware update.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual 4.8 Information 4.8.1 Version The version interface is shown as in Figure 4-95. Here you can view system hardware features, software version, release date and etc. Please note the following information is for reference only. Figure 4-95 4.8.2 Log Here you can view system log. See Figure 4-96.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Please refer to the following sheet for log parameter information. Parameter Function Start time Set the start time of the requested log. (The earliest time is 2000/1/1) End time Set the end time of the requested log. (The latest time is 2037/12/31) Type Search Log information Log type. You can select log type from the drop down list and then click search button to view the list. You can click the stop button to terminate current search operation.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual 5 Alarm Please note some series product does not support this function. Click alarm function, you can see an interface is shown as in Figure 5-1. Here you can set device alarm type and alarm sound setup. Figure 5-1 Please refer to the following sheet for detailed information. Type Parameter Function Alarm Motion detection System alarms when motion detection alarm type occurs, Disk full System alarms when disk is full.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual Type Parameter Path Function Here you can specify alarm sound file.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual 6 Log out Click log out button, system goes back to log in interface. See Figure 6-1. Figure 6-1 Note: This manual is for reference only. Slight difference may be found in user interface. All the designs and software here are subject to change without prior written notice. All trademarks and registered trademarks mentioned are the properties of their respective owners.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual FCC Compliance Statement 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 2.
Dahua 2 Inch PTZ Camera Web 3.0 Operation Manual 4. RF exposure warning This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.