Specifications

ManualsBrandsZHEJIANG JIECANG LINEAR MOTION TECHNOLOGY ManualsElectronicsJCP35W2

This product is a standard Qi wireless charger, which supports wireless charging for all

kinds of mobile phones (including Samsung S7, Note8, iPhone 8, iPhone, etc.) or other

devices in line with the Qi charging protocol. It can output up to 10W of charging

power, and the charging distance can meet the range of 0mm to 6mm.

1.0 Electrical Specification

Model JCP35W2

Rated Voltage Range 24Vdc-33Vdc

Rated Voltage 33Vdc

Charge Distance 0mm-6mm

Standby Power Consumption ≤1W

Rated Input Current

0.63Adc @3mm，10W Load，24VInput

Efficiency

>65% @3mm，10W Load，24V Input

Input Over-Power Protection（Power

Transfer Phase）

30W

OvertemperatureProtection 85℃

2.0 Working status indication

2.1 Charge Status Indication

Charger Status

Standby C

harging Fault

Green LED OFF ON Blink（1Hz）

RedLED OFF OFF OFF

The transmitter has five working states, namely, power on, normal standby, normal

charging, full power and failure. After the power on, the red light is always on, and the green

light does not glow after flashing 1 times; When the normal standby, the red light is always

on; When charging normally, the green light is always on and the red light is off; When

abnormal or malfunction occurs, the green light blinks and the red light goes off. Abnormal

phenomena include over-offset location of the receiver, over-high PCBA temperature, entry

of metal foreign matter, overcurrent of input current, and overvoltage of input voltage, etc.

3.0 Protection Character

3.1 Input Over-Current Protection

The Qi transmitter has the input current overcurrent protection. Once the overcurrent

fault is triggered, the transmitter will automatically shut down and restart, and try to

reconnect. If the overcurrent protection is triggered for many times, the system will stop

working and flash the light to alarm.

3.2 Over-Temperature Protection

The QI transmitter has over-temperature protection. when the temperature on PCBA

exceeds a certain value (85℃), the transmitter will stop working in time, thus ensuring safety.

Once the temperature drops to a proper range (75℃), the transmitter will automatically

resume its normal working state.

3.3 Foreign body detection Protection FOD Protection

The Qi transmitter has the function of foreign body detection. When the transmitter

enters the power transmission stage, a metal foreign body entering the charging area will be

Summary of content (5 pages)

PAGE 1
This product is a standard Qi wireless charger, which supports wireless charging for all kinds of mobile phones (including Samsung S7, Note8, iPhone 8, iPhone, etc.) or other devices in line with the Qi charging protocol. It can output up to 10W of charging power, and the charging distance can meet the range of 0mm to 6mm. 1.0 Electrical Specification Model JCP35W2 Rated Voltage Range 24Vdc-33Vdc Rated Voltage 33Vdc Charge Distance 0mm-6mm Standby Power Consumption ≤1W Rated Input Current 0.
PAGE 2
reco ognized. The e transmitter will self-lock until the re eceiver move es away, and d the charger will auto omatically re esume its norrmal working g state. 4.0 Mechanical M s size Area Heightt PCB B 47.7m mm*55mm 1.6mm m Com mponent abo ove PCB - 7.5mm m Tran nsmitter Coil + Magneticc Shielding φ44m mm 2mm 4.1 Mounting M m method. 5.0S Safety and EM MC 5.
PAGE 3
6.1 Work Environment Temperature 0℃-35℃ Humidity 10%-90% 6.2 Storage environment Storage environment -20℃-80℃ Humidity 5%-95% 7.0 Test Instruction 7.1Fixture test Because the coil size of the fixture is generally smaller than that of the phone, when testing with a 10W fixture, higher than 6mm will result in undervoltageand failure to charge properly. At the same time, prolonged testing with the fixture at extreme temperatures (>35°C) may result in overheating protection of the transmitter. 7.
PAGE 4
the card. 3.Make sure that the thickness of the upper desktop is within the range of thespecification, otherwise it will not be able to charge. 4.Avoid humidity, liquid, fire and high temperature as it may cause hazard to users. 5.Do not try to disassemble or modify the product. 6.Do not attempt to disassemble to avoid fire hazard or short-circuit 7.Any of damage by abnormal use of product will void the manufacture warranty. 8.
PAGE 5
FCC Statement： Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference,and (2) this device must accept any interference received, including interference that may cause undesired operation.