User's Manual Part 1

ManualsBrandsZhejiang shenghui lighting Co., Ltd. Shanghai Branch ManualsElectronicsLED Lamp

User Manual

A01BR30 LED Lamp

LED + WiFi Range Extender

Features

 Install like any other light bulb. Easy to setup and enjoy the extended WiFi

signal coverage evenly.

 Supports two WiFi network mode: Access Point (AP) / Repeater

 Two buildin antennas for high throughput data exchange rate of maximum

300Mbps

 Compatible with most smart phones, tablets and computers that support WiFi

IEEE 802.11b/g/n standard at 2.4GHz.

 Remote LED lights ON/OFF and dimming control individually or by group

 Download the free Boost Android or iOS App to explore even greater

functionality

Box Contents

 One A01BR30 Bulb

 User Manual

 Limited Written Express Warranty

Product Specifications

 Power Supply: 120V AC, 60Hz, 0.11A (Typ.)

 Lamp Socket: E26 (US Version)

 Power Consumption: 12W (LED+WiFi Repeater)

 Power factor: 0.85 (Min.)

Summary of content (9 pages)

PAGE 1
User Manual A01BR30 LED Lamp LED + WiFi Range Extender Features  Install like any other light bulb. Easy to setup and enjoy the extended WiFi signal coverage evenly.  Supports two WiFi network mode: Access Point (AP) / Repeater  Two buildin antennas for high throughput data exchange rate of maximum 300Mbps  Compatible with most smart phones, tablets and computers that support WiFi IEEE 802.11b/g/n standard at 2.4GHz.
PAGE 2
       Operating Temperature: 20° C ~ +40° C Store Temperature: 40° C ~ +70° C Operating Humidity: 10% ≤ RH ≤ 95%, Non condensation Atmospheric Pressure: 86kPa ~ 106kPa Colour: Neutral White Dimensions: 5.32" (H) x Φ 3.74" (Dia.) Weight: 11.82oz (approx.) LED Lights       Power: 8.
PAGE 3
INSTALLATION INSTRUCTIONS WARNING TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE BACK COVER OR TAKE APART. THERE ARE NO SERVICEABLE PARTS INSIDE. 1. Before installing the Boost into an E26 light bulb socket, turn the light switch to the OFF position. (DO NOT USE WITH EXTERNAL OR OUTSIDE DIMMERS). 2. Screw the bulb into an E26 socket and turn the power on. 3. On the portable smart device (e.g.
PAGE 4
6. The App will search and list out nearby available wireless router/s automatically. Choose one of the routers as the root router. Type in the Access Password and press “Next” to move forward. 7. The App will also search and list out nearby available boost A01BR30 bulb/s. The default SSID of the bulb is “SENGLED_AP”. (ATTENTION: Figure shows below, SSID Name of "LL_AP_00_**" only for engineering samples demo). Press the “Start” tab for configuring all nearby available boost A01BR30 bulbs.
PAGE 5
8. After the process of bulb network configuration has been succeeded, boost A01BR30 bulb/s will reboot (THIS PROCESS MAY TAKE FEW MINUTES, PLEASE BE PATIENCE). Press “Done” and return to the home page. 9. The App begins to search the configured online LED bulb/s.
PAGE 6
REFRESH THE LIST FROM TIME TO TIME). After searching out all configured bulbs, the interface shows a Main Control Page. This can be used to control the overall LED light dimming and ON/OFF. 10. To control the LED bulb individually, pull up the bulb list at the bottom, each bulb can be dimmed separately. Click the arrow on the right, and it goes to the bulb wireless network configuration page.
PAGE 7
11. Under the 'General' tab, the wireless network parameters of the bulb are listed (such as MAC address, IP Address). User can change bulb's SSID (listed on the WLAN table, visible name to public), or Name (listed on the boost by Sengled App) to a more meaningful name, such as "Living Room AP" or "Living Room WiFi". Press "Apple" to active such changes. Under the 'Security' tab, user can change the Encryption Mode, or change the bulb access Password. Press "Apply" to active such changes. 12.
PAGE 8
13. If the bulb cannot be detected by the portable smart devices or App in any ways, user can press the physical RESET button to reset the configuration of the bulb (in the middle of the LED lens), as shown below.
PAGE 9
IMPORTANT SAFETY INSTRUCTIONS • Read and keep these safety instructions. • Heed all warnings contained within these instructions. • Please follow all user manual instructions when installing the product. • Clean SENGLED product only with a dry towel. • This Product is intended for indoor use only. • Do NOT use this product outdoors. • Do NOT get this product wet and do NOT use near any water source. • The product should not be exposed to dripping or splashing liquids of any kind.