User's Manual

品名：Headblue3英文说明书
发行日期：2013/10/31
版本：x1.0
要求：
1. 128g铜版纸
2. 双面单色印刷
3. 筒包折(参照提供样品)
4. 要求印刷清晰,对折整齐
更新日志：
制作：
审核：
批准：
Press the volume button "+" or "-" to turn volume up or down.
you hear "beep" voice prompts once reach the maximun volume,
you hear "toot" voice prompts once reach the minimun volume.
Call
Headblue3 INSTRUCTION
NFC pairing
Music
Following items are included
Start here
Basic operation
3.5mm audio jack
USB cable
Product overview
Volume adjust
LED indicator and voice prompts
Volume - / Trackforward
Volume + / Trackback
Multifunction button
Status indicator
Charge port
3.5mm audio input jack
Instruction
Power on
Power off
Pairing
NFC pairing
Standby
Disconnect
Incoming call
Battery low
LED status
Flashes blue 3 times
Flashes red 3 times
Flashes red and blue alternately
Flashes red and blue alternately
Flashes blue twice every 5 seconds
Flashes blue continuously
Flashes red twice every 2 seconds
Voice prompts & Alerts
Power on
Power off
Pairing
Pairing
Connection successful
/
/
Battery low
Charging Stays red while charging
Stays blue once fully charged
/
Connection lost
● Press and hold the Multifunction button for about 5
seconds to entel pairing mode, the LED indicator flashes
red and blue alternately. Voice prompts "Pairing".
● Activate Bluetooth on your phone and set it to search for
new devices.
● Select "Headblue3" . If you phone asks, enter 0000 (four
zeros) for the passcode or accept the connection. The
LED indicator stops flashing red and blue once
successfully paired. Voice prompts "Connection
successful".
Pair one phone
Pairing
Pair another phone
Multipoint technology enables you to pair another phone
and take a call from either.
To pair with another mobile phone, follow the steps for
“Pair One Phone”. After pairing successfully, restart the
headphone to connect to 2 paired mobile phone
automatically.
Press and hold Multifunction button for 2 seconds to turn
on Bluetooth headset, after 5 seconds, hold an NFC device
against the NFC zone of the headphone. The LED indicator
flashes red and blue, you hear voice prompts "Pairing", the
LED indicator stops flashing red and blue once successfully
paired, you hear voice prompts "Connection successful".
NFC detection area
Answer a call
End a call
Reject a call
Redial the last call
Mute on/off
Press the Multifunction button.
Press the Multifunction button.
Double-press the Multifunction button in standby mode.
The mobile phone will redial the last call number.
Press the Volume button "-" for about 2 seconds to mute
on/off.
Press and hold the Volume button "+" for about 2
seconds.
Switch between the headphone and phone
Press the Volume button "+" for about 2 seconds during a
call, the call will be switched to the mobile phone, redo
this operation again, the call will be switched to the
headphone.
Music play / pause
Press Multifunction button once to play / pause music.
(Some phones may require you to start a media player
first)
Track back/forward
Press Track back once to skip track backward, press
Track forward once to skip track forward.
Switch Music and Call
When a call rings during a music playing, the music
automatically pauses to allow you to answer or ignore
the call. Once the call is ignored or ends, the music is
resumed.
(Need media player support)
Battery Indicator
More features
When the headphone is connected to a device with iOS
system, a battery indicator will appear at the upper right of
the system, indicating battery status of the headphone.
Listen music via 3.5mm Jack
● Connect the headphone to a 3.5 mm jack connector on your
mobile device or PC using the supplied music cable.
● Turn on the music player on your mobile device or computer, you
enjoy music from your headphone.
(Call functions are disabled in this mode)
Charging
Your new headphone has enough power to pair and make
a few calls.
When battery is low, you will hear the voice prompt "
Battery low ". It takes 2.5 hours to fully charge the
headphone. While charging, the battery indicator light is
red, the indicator light stays blue charging is complete.
Power off
Press and hold the Multifunction button for about 3
seconds. The red LED will flash three times rapidly before
turning off. A voice prompt "Power off" will appear,
indicating the headphone has been turned off.
Hardware reset
Press and hold the Multifunction button, connect the
headphone to a USB charger, the LED indicator flashes
red, hardware reset is done in about 2 seconds.
EQ setting
During a music playing, double-press Multifunction
button to cycle through EQ setting: original, bass,
treble, rock, pop.
End current call and answer new call
When a new call rings during a call, press the
Multifunction button to answer new call and end current
call simultaneously.
On hold current call and answer new call
When a new call rings during a call, hold the
Multifunction button for 2 seconds to hold current call
and answer new call. To switch between held call and
active call, Hold the multifunction button for 2 seconds.
Note: The lifetime of the battery will be significantly reduced if your device is
left uncharged for a long period. We recommend that you recharge your device
at least once a month.
FCC ID:2AAIH-HB03
Bluetooth headset