User`s guide

S-REGISTERS

S0 Auto-Answer Ring Number 1 0(Disable) or 1–255 rings

S2 AT Escape Character 43(+) 0–127 ASCII

S3 Carriage Return Character 13 0–127 ASCII

S4 Line Feed Character 10 0–127 ASCII

S5 Backspace Character 8 0–127 ASCII

S6 Blind Dial Pause 2 2–255 seconds

S7 No Answer Time-out 45 1–255 seconds

S8 “,” Pause Time for the Dial Modifier 2 0–255 seconds

S10 No Carrier Disconnect 2 0–254 (10ths of a second) or 255(Disable)

S12 Escape Sequence Guard Time 50 0–255 in 20-millisecond increments

S14 Asymmetric Rate (Dial) 0 0=Enable; 1=Disable

S15 Asymmetric Rate (Leased) 0 0=Enable; 1=Disable

S18 Test Time-out 0(disabled) 0–255 seconds

S23 Proactive Retrain 0 0=Enable; 1=Disable

S25 AutoSync Start Pause 0(disabled) 0–30 seconds

S26 RTS/CTS Delay 0 0–255 seconds

S28 SDC Negotiation 0 0=LAPM_Buffer; 1=LAPM_Discon

S29 SDC Idle Fill 0 0=Flag_Fill; 1=Mark_Fill

S30 Sync DTE Rate 0 0=12800 bps; 1=115200; 3=96000; 4=78800;

5=72000; 6=64000; 7=57600; 8=56000; 9=48000;

10=38400; 11=28800; 12=19200; 13=14400;

14=9600; 15=4800; 16=2400; 17=1200

S31 SDC Bit Encoding 0 0=NRZ; 1=NRZI

S32 Sync DTE CRC 0 0=Ignore; 1=CRC16

S33 Buffer Size In Buffer Mode 0 0=Normal; 1=Minimized

S35 Auto Redial 0 0=Dir1; 1=Dirs1–2; 2=Dirs1–3... 9=Dirs1–10

S36 Rate Auto Originate 0 0(Disable) or 1(4800) – 6(16,800)

S37 Auto Redial 0 0(Dir 1) – 9(Dirs 1–10)

S38 DTR Cont Repeat 0 0=Disable, 1=Enable

S39 RX Buffer Disconnect Delay 0 0(Disable) or 1–255 seconds

S40 Auto Make Busy 0 0=Disable, 1=Enable

S41 Dial Line Rate 29 1=14400(V.32bis); 2=12000(V.32bis);

3=9600(V.32bis); 4=7200(V.32bis);

5=4800(V.32bis); 6=2400(V.22bis); 7=1200(V.22);

8=1200(212A); 10=0–300(V.21); 11=0–300(103J);

20=19200(V.32terbo); 21=16800(V.32terbo);

27=33600(V.34); 28=31200(V.34);

29=28800(V.34); 30=26400(V.34);

31=24000(V.34); 32=21600(V.34);

33=19200(V.34); 34=16800(V.34);

35=14400(V.34); 36=12000(V.34);

37=9600(V.34); 38=7200(V.34); 39=4800(V.34);

40=2400(V.34)