Instruction manual

ManualsBrandsZhone ManualsComputer equipmentDNE4500-P

DNE4500-P-6-AC and DNE4500-P-6-DC

6-Port DS3 Network Extender Provider Units: AC and DC Versions

1.0 INSTALLATION

1.1 Unpack and Inspect the Equipment

The following components should be included:

If there is visible damage, do not attempt to connect the device; contact Customer Support at 1-877-638-

2638 (001-603-427-0600 for international customers) or support@NetToNet.com.

1.2 Select the Installation Site

The maximum recommended ambient temperature for the DNE4500-P-6 is 50° Celsius (122° Farenheit).

1.2.1 Tabletop Use

Affix the (4) provided rubber bumpers to the bottom corners of the unit to provide surface grip.

Ensure that the DNE4500-P-6 is placed such that the cables will not become a tripping hazard or

pull loose from the unit.

1.2.2 Rack Installation

Using a Phillips Screwdriver, attach the (2) rack mount brackets to the sides of the DNE4500-P-6

with the (10) bracket screws provided. Mount the chassis to the rack using one of the two provided

sets of (4) rack mount screws (whichever size fits the rack being utilized). Check the rack for

stability, ensuring that installation of the DNE4500-P-6 has not caused the rack to become top-

heavy.

Installation Instructions

AUTION

Net to Net Technologies strongly recommends the use of proper electrostatic discharge (ESD) precautions when handling

this equipment.

1 DNE4500-P-6 10 #6 Phillips Rack Mount Bracket Screws

4 Rubber Bumpers 4 #12 Phillips Rack Screws

1 Power Cord (AC Versions only) 4 #10 Phillips Rack Screws

2 Rack Mount Brackets 1 Installation Instruction manual

AUTION

Do not block power supply vents or otherwise restrict airflow around the DNE4500-P-6.

220-0000018 rev 02

Summary of content (5 pages)

PAGE 1
Installation Instructions DNE4500-P-6-AC and DNE4500-P-6-DC 6-Port DS3 Network Extender Provider Units: AC and DC Versions CAUTION Net to Net Technologies strongly recommends the use of proper electrostatic discharge (ESD) precautions when handling this equipment. 1.0 INSTALLATION 1.
PAGE 2
1.3 Power up the DNE4500-P-6 Upon start up of the DNE4500-P-6, the Ethernet link for each port will remain disabled until the corresponding DS3 network link has been established. 1.3.1 AC Power Plug the AC Power Supply Cord into the back of the DNE4500-P-6-AC and connect it to the power source. Turn the power switch ON (ON="|", OFF="O") and verify that the PWR (Power) LED on the front of the unit is illuminated. 1.3.
PAGE 3
1.5 Connect the DS3 Cable(s) NOTE The DNE4500-P-6 may be connected via DS3 line to either a DS3 network extender subscriber unit (DNE4500-S) or another DS3 network extender provider unit (DNE4500-P, DNE4500-P-6). EXCEPTION: a provider to provider connection will not work if both units are configured with loop timing. Plug the DS3 Tx and Rx cables into the corresponding BNC ports on the front of the DNE4500-P-6 for each port being connected to a remote DS3 modem.
PAGE 4
2.0 ADDITIONAL INFORMATION 2.1 LED Indicators LED State Indication Additional Information Power solid green unit is operational If the Power LED is not illuminated, it is likely that the DNE4500-P-6 is not receiving power and therefore none of the LEDs will be illuminated. Lnk/Alm pulsing green DS3 connection is established The port is receiving valid data or status packets from and operational the remote DNE4500.
PAGE 5
2.2 Regulatory Compliance for Class A Equipment 2.2.1 US Federal Communications Commission (FCC) Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.