Specifications

ManualsBrandsZhone ManualsComputer equipmentHotwire 6390

6390-A2-GK40-00 September 2002

Hotwire

ReachDSL

™

Modem, Model 6390

with Inline Phone Filter

Installation and Operation Supplement

Document Number 6390-A2-GK40-00

September 2002

Contents

Hotwire 6390 ReachDSL Modem Overview ...................................................... 2

Hotwire ReachDSL System ......................................................................... 3

Power-On ........................................................................................................... 4

Status LEDs ................................................................................................ 4

Troubleshooting ................................................................................................. 5

Increasing the Number of End-User Systems ................................................... 6

Optional ReachDSL Modem Wall Placement .................................................... 8

ReachDSL Modem Hardware Template ...................................................... 9

Hotwire 6390 ReachDSL Modem Commands ................................................... 10

Downloading Hotwire 6390 ReachDSL Modem Software ................................. 11

Building a Management PVC to the Model 8355 Line Card in an 8820

GranDSLAM Network .................................................................................. 12

Building a Management PVC through the 4200 GranDSLAM System ........ 14

Downloading Software to the ReachDSL Modem ....................................... 15

Technical Specifications for Hotwire 6390 ReachDSL Modem .......................... 16

Summary of content (18 pages)

PAGE 1
Hotwire® ReachDSL™ Modem, Model 6390 with Inline Phone Filter Installation and Operation Supplement Document Number 6390-A2-GK40-00 September 2002 Contents Hotwire 6390 ReachDSL Modem Overview ...................................................... 2 Hotwire ReachDSL System ......................................................................... 3 Power-On ........................................................................................................... 4 Status LEDs ..............................
PAGE 2
Hotwire 6390 ReachDSL Modem Overview The Hotwire® 6390 ReachDSL™ Modem is a component in the Hotwire ReachDSL System and interoperates with the Hotwire 8355 ReachDSL Card in the Hotwire 8820 GranDSLAM™ system and in the 4200 GranDSLAM system. The GranDSLAM system provides high-speed Internet or corporate LAN access over traditional twisted-pair copper telephone wiring. The ReachDSL technology: Operates over existing copper wire with existing telephone jacks.
PAGE 3
Hotwire ReachDSL System Copper pairs run from the central office (CO) to the customer premises (CP) to create the local loop. The local loop terminates on the customer premises at the demarcation point.
PAGE 4
Power-On When power is applied, the ReachDSL modem performs self-diagnostics and the PWR LED is on. The self-diagnostics includes a power-on self-test and all of the LEDs turn on for one second. Power – green Alarm – red Test – yellow DSL Line – green Transmit/Receive – green Ethernet Link – green PWR ALM TST LINE TX/RX ETHERNET ReachDSL 01-17003 Status LEDs All of the LEDs turn on and off during the power-on self-test.
PAGE 5
Troubleshooting LED Symptom Action All LEDs are on. If LEDs remain on after ten minutes, the modem is not functional. Contact the service provider. ALM LED remains on. The power-on self-test may have failed. Unplug the unit and reapply power. If the alarm LED is still on, contact the service provider. Ethernet LED is off. Verify that the Ethernet cable is securely installed at both ends, and at least one PC is connected and powered on.
PAGE 6
Increasing the Number of End-User Systems A single end-user system is attached to the Hotwire 6390 ReachDSL Modem by using an Ethernet straight-through cable. To increase the number of end-user systems, connect all the PCs to an Ethernet hub and connect the modem to the hub’s uplink port using a standard straight-through cable for both connections. The Hotwire ReachDSL port card supports 32 hosts/subnets per DSL port and the Hotwire ReachDSL Modem supports up to 256 MAC entries.
PAGE 7
The Ethernet interface connector uses an 8-pin, non-keyed modular plug. To connect the DSL modem to an uplink port on an Ethernet hub or PC with an Ethernet NIC card, use the straight-through connection.
PAGE 8
Optional ReachDSL Modem Wall Placement The Hotwire 6390 ReachDSL Modem is designed for tabletop placement. The modem can also be mounted on a wall. To mount the modem, you will need: ❑ Two slotted-head #6 self-threading screws with plastic anchors ❑ Drill and 3/16" drill bit for the plastic anchors ❑ Screwdriver A template with the dimensions for the two screws is provided. See ReachDSL Modem Hardware Template on page 9. Procedure To mount the Hotwire 6390 ReachDSL Modem: 1.
PAGE 9
Bottom 12.95 cm or 5.
PAGE 10
Hotwire 6390 ReachDSL Modem Commands The Hotwire 6390 ReachDSL Modem provides the commands listed in Table 1, Hotwire ReachDSL 6390 Modem Commands. Use a PC connected to the Ethernet jack on the rear panel of the modem or Telnet into the modem to enter these commands. Table 1. Hotwire ReachDSL 6390 Modem Commands (1 of 2) Command Syntax Argument Function Displays help information.
PAGE 11
Table 1. Hotwire ReachDSL 6390 Modem Commands (2 of 2) Command Syntax Argument Function Description Initiates a firmware upgrade and resets the modem.
PAGE 12
Building a Management PVC to the Model 8355 Line Card in an 8820 GranDSLAM Network Before attempting to download software to the Hotwire 6390 ReachDSL modem, you must first build a management Permanent Virtual Circuit (PVC) through the DSLAM (including the SCM card).
PAGE 13
Procedure To create a PVC from the Model 8355 line card port to the Hotwire 6390 ReachDSL modem: 1. Select the ATM Cross Connect screen from Model 8355 line card. Follow this menu selection sequence: Configuration → ATM Switch → ATM Cross Connect (A-E-B) 2. Create a management PVC in the cross connect table of the Model 8355 line card as shown below: 3. Select the Cross Connect Sorted by Slot screen from SCM card.
PAGE 14
Building a Management PVC through the 4200 GranDSLAM System Before attempting to download software to the Hotwire 6390 ReachDSL modem, you must first build a management Permanent Virtual Circuit (PVC) through the GranDSLAM 4200.
PAGE 15
Procedure To create a PVC from the GranDSLAM 4200 port to the Hotwire 6390 ReachDSL modem: 1. Log into the GranDSLAM 4200 unit using the ACT-USER command. For example, type: ACT-USER:TAMPA:SUPERUSER:100::******** 2. Create a VCL to the upstream network (on the NT) with VPI=1 and VCI=33 using the ENT-VCL command. For example, type: ENT-VCL:TAMPA:NTVCL-1-33:100::1,1; 3. Create a VCL to the Hotwire 6390 ReachDSL Modem attached to Port 1 (on the LT) with VPI=0 and VCI=33 using the ENT-VCL command.
PAGE 16
Technical Specifications for Hotwire 6390 ReachDSL Modem Item Specification* Height x Width x Depth 3.71 cm x 14.54 cm x 11.00 cm (1.46" x 5.72" x 4.33") Weight 0.20 kg (0.45 lb.) Power Class 2 Transformer normal service input voltage range Input: 100 VAC (+10%), 50 Hz; 120 VAC (+10%), 60 Hz; or 230 VAC (+10%), 50/60 Hz Output: 5 VDC nominal, minimum 0.
PAGE 17
Warranty, Sales, Service, and Training Information Contact your local sales representative, service representative, or distributor directly for any help needed. For additional information concerning warranty, sales, service, repair, installation, documentation, training, distributor locations, or Paradyne worldwide office locations, use one of the following methods: Internet: Visit the Paradyne World Wide Web site at www.paradyne.com. (Be sure to register your warranty at www.paradyne.com/warranty.
PAGE 18
*6390-A2-GK40-00*