User`s guide

ManualsBrandsZhone ManualsSoftwareMIM-2T1

MIM2-A2-GZ41-00 October 2004 1

MIM-2T1

Installation Instructions

Document Number MIM2-A2-GZ41-00

October 2004

Contents

Software and Firmware License Agreement ...................................................... 1

Product Documentation Online .......................................................................... 3

Unpacking and Inspecting the Equipment ......................................................... 3

Installing the MIM-2T1 ....................................................................................... 3

Connecting the T1 Line ...................................................................................... 4

T1 RJ45 Pinouts ................................................................................................ 5

T1 Default Settings ............................................................................................ 6

T1 Parameter Configuration .............................................................................. 6

LED Indicators ................................................................................................... 8

Regulatory Notices ............................................................................................ 9

Warranty, Sales, Service, and Training Information ........................................... 10

Software and Firmware License Agreement

The terms and conditions of this License Agreement (the “Agreement”) will apply

to the software and/or firmware (individually or collectively the “Software”)

incorporated into the Paradyne product (the “Product”) purchased by you and any

derivatives obtained from the Software, including any copy of either. If you have

executed a separate written agreement covering the Software supplied to you

under this purchase, such separate written agreement shall govern.

Paradyne Corporation (“Paradyne”) grants to you, and you (“Licensee”) agree to

accept a personal, non-transferable, non-exclusive, right (without the right to

ONCE YOU HAVE READ THIS LICENSE AGREEMENT AND AGREE TO ITS

TERMS, YOU MAY USE THE SOFTWARE AND/OR FIRMWARE INCORPORATED

INTO THE PARADYNE PRODUCT. BY USING THE PARADYNE PRODUCT YOU

SHOW YOUR ACCEPTANCE OF THE TERMS OF THIS LICENSE AGREEMENT.

IN THE EVENT THAT YOU DO NOT AGREE WITH ANY OF THE TERMS OF THIS

LICENSE AGREEMENT, PROMPTLY RETURN THE UNUSED PRODUCT IN ITS

ORIGINAL PACKAGING AND YOUR SALES RECEIPT OR INVOICE TO THE

LOCATION WHERE YOU OBTAINED THE PARADYNE PRODUCT OR THE

LOCATION FROM WHICH IT WAS SHIPPED TO YOU, AS APPLICABLE, AND YOU

WILL RECEIVE A REFUND OR CREDIT FOR THE PARADYNE PRODUCT

PURCHASED BY YOU.

Summary of content (10 pages)

PAGE 1
MIM-2T1 Installation Instructions Document Number MIM2-A2-GZ41-00 October 2004 Contents Software and Firmware License Agreement ...................................................... 1 Product Documentation Online .......................................................................... 3 Unpacking and Inspecting the Equipment ......................................................... 3 Installing the MIM-2T1 .......................................................................................
PAGE 2
sublicense) to use the Software, solely as it is intended and solely as incorporated in the Product purchased from Paradyne or its authorized distributor or reseller under the following terms and conditions: 1. Ownership: The Software is the sole property of Paradyne and/or its licensors. The Licensee acquires no title, right or interest in the Software other than the license granted under this Agreement. 2.
PAGE 3
Product Documentation Online Complete documentation for Paradyne products is available at www.paradyne.com. Select Support → Technical Manuals. To order a paper copy of a Paradyne document, or to speak with a sales representative, please call 1-727-530-2000. Unpacking and Inspecting the Equipment HANDLING PRECAUTIONS FOR ! STATIC-SENSITIVE DEVICES This product is designed to protect sensitive components from damage due to electrostatic discharge (ESD) during normal operation.
PAGE 4
Connecting the T1 Line A primary feature of the MIM-2T1 is loop bonding capability, though the module can function with a single T1 connection as well. NOTE: A MIM-2T1 must be connected with T1 provider equipment; a connection between the MIM-2T1 and T1 subscriber equipment will not function. Loop Bonded Connection Using two T1 lines for one network connection (loop bonding ) will net twice the speed and data passing capability as a single T1 connection.
PAGE 5
Single T1 Connection A single line connection may be established between a MIM-2T1 and Paradyne’s T1 provider equipment (stand-alone or IP DSLAM module), regardless of loop bonding capability. Procedure 1. If a ferrite choke is supplied with your MIM: — Open the ferrite choke. — Make a loop at the end of your cable and close it in the ferrite choke. Position the choke as close as possible to the RJ45 connector. — Snap shut the ferrite choke. 2.
PAGE 6
T1 Default Settings No configuration is necessary for the MIM-2T1 to operate at default settings: Speed: Adaptive. The MIM-2T1 determines timeslot and bandwidth configurations via communication with the remote T1 equipment to which it is connected. Each T1 connection has the capability of receiving data across all 24 channels at 1,536 kbps.
PAGE 7
Line Code Line code is the T1 mode of transmission. The two line code options outlined below both fall within the International Telecommunication Union Telecommunication Standardization Sector (ITU-T) G.703 Standards for Transmission Facilities. Bipolar with 8 Zero Substitution (Default) – Bipolar with 8 Zero Substitution (B8ZS) is used to accommodate the minimum ones density requirement in the North American public network.
PAGE 8
LED Indicators Table 1. LEDs ADDITIONAL INFORMATION LED STATE INDICATION T1 Connections (Port 1 Lnk and Port 2 Lnk) Flashing Green* T1 connection is established and active. Traffic is flowing. Solid Green Problematic T1 connection. A connection exists but there is indication of a problem with the T1 line. No Illumination Red AlarmThe incoming connection to the MIM-2T1 has been lost; no data is being received.
PAGE 9
! Regulatory Notices ! UNITED STATES – EMI NOTICE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
PAGE 10
Warranty, Sales, Service, and Training Information Contact your local sales representative, service representative, or distributor directly for any help needed. For additional information concerning warranty, sales, service, repair, installation, documentation, training, distributor locations, or Paradyne worldwide office locations, use one of the following methods: Internet: Visit the Paradyne World Wide Web site at www.paradyne.com. (Be sure to register your warranty at www.paradyne.com/warranty.