Instruction manual

ManualsBrandsZhone ManualsComputer equipmentSNE2000G-P

SNE2000-P, SNE2000-S, SNE2000Q-P and

SNE2000Q-S Network Extenders

Installation Instructions

Document Number SNE2-A2-GN10-00

October 2004

Contents

Software and Firmware License Agreement ................................................. 1

Package Contents ........................................................................................ 3

Connecting to Power .................................................................................... 3

Configuring the SNE2000 ............................................................................. 4

Connecting the SDSL Line ........................................................................... 6

Connecting the Ethernet Line ....................................................................... 6

LED Indicators .............................................................................................. 7

EMI Notices .................................................................................................. 10

Important Safety Instructions ........................................................................ 10

Product Documentation Online ..................................................................... 11

Software and Firmware License Agreement

The terms and conditions of this License Agreement (the “Agreement”) will apply to the

software and/or firmware (individually or collectively the “Software”) incorporated into

the Paradyne product (the “Product”) purchased by you and any derivatives obtained

from the Software, including any copy of either. If you have executed a separate written

agreement covering the Software supplied to you under this purchase, such separate

written agreement shall govern.

ONCE YOU HAVE READ THIS LICENSE AGREEMENT AND AGREE TO ITS

TERMS, YOU MAY USE THE SOFTWARE AND/OR FIRMWARE INCORPORATED

INTO THE PARADYNE PRODUCT. BY USING THE PARADYNE PRODUCT YOU

SHOW YOUR ACCEPTANCE OF THE TERMS OF THIS LICENSE AGREEMENT.

IN THE EVENT THAT YOU DO NOT AGREE WITH ANY OF THE TERMS OF THIS

LICENSE AGREEMENT, PROMPTLY RETURN THE UNUSED PRODUCT IN ITS

ORIGINAL PACKAGING AND YOUR SALES RECEIPT OR INVOICE TO THE

LOCATION WHERE YOU OBTAINED THE PARADYNE PRODUCT OR THE

LOCATION FROM WHICH IT WAS SHIPPED TO YOU, AS APPLICABLE, AND YOU

WILL RECEIVE A REFUND OR CREDIT FOR THE PARADYNE PRODUCT

PURCHASED BY YOU.

Summary of content (12 pages)

PAGE 1
SNE2000-P, SNE2000-S, SNE2000Q-P and SNE2000Q-S Network Extenders Installation Instructions Document Number SNE2-A2-GN10-00 October 2004 Contents Software and Firmware License Agreement ................................................. 1 Package Contents ........................................................................................ 3 Connecting to Power .................................................................................... 3 Configuring the SNE2000 ............................
PAGE 2
Paradyne Corporation (“Paradyne”) grants to you, and you (“Licensee”) agree to accept a personal, non-transferable, non-exclusive, right (without the right to sublicense) to use the Software, solely as it is intended and solely as incorporated in the Product purchased from Paradyne or its authorized distributor or reseller under the following terms and conditions: 1. Ownership: The Software is the sole property of Paradyne and/or its licensors.
PAGE 3
9. Upon such termination, the Licensee shall refrain from any further use of the Software and destroy the original and all copies of the Software in the possession of Licensee together with all documentation and related materials. 10. This Agreement shall be governed by the laws of the State of Florida, without regard to its provisions concerning conflicts of laws. Package Contents Unpack and Inspect the Equipment.
PAGE 4
Configuring the SNE2000 Configuration switches for the SDSL port are on the back of the SNE2000, numbered from left to right, 1-4. Bandwidth Switches 1–3 configure bandwidth on the SNE2000-P and SNE2000Q-P. Switches 1–3 on the SNE2000-P and SNE2000Q-P provide eight bandwidth options for the SDSL port. Distance capabilities listed in the following tables assume the use of 26 American Wire Gauge (AWG) cable. Connections made with cable of a heavier gauge will link up at greater distances.
PAGE 5
Table 2. SNE2000Q-P Bandwidth and Distance Options Switch Position Distance 1 2 3 Bandwidth (kbps) Feet down down down 2,320 10,400 3,170 down down up 2,064 10,800 3,292 down up down 1,552 13,400 4,084 down up up 1,040 14,800 4,511 up down down 784 15,800 4,816 up down up 528 17,400 5,304 up up down 400 18,200 5,547 up up up 272 19,200 5,852 Meters NOTE: Bandwidth cannot be configured on the SNE2000-S or SNE2000Q-S.
PAGE 6
Connecting the SDSL Line An SNE2000-S must be connected via an SDSL line to an SNE2000-P, a Mini DSLAM, a Micro DSLAM or an IP DSLAM interface module. Likewise, an SNE2000Q-S must be connected via SDSL line to an SNE2000Q-P, Mini DSLAM, Micro DSLAM or IP DSLAM interface module. Neither a subscriber-to-subscriber nor a provider-to-provider connection will function. Procedure 1. Plug your SDSL cable into the SDSL RJ45 port on the back of the SNE2000. 2.
PAGE 7
LED Indicators Table 4. LEDs (1 of 2) ADDITIONAL INFORMATION LED STATE INDICATION Power Solid Green SNE2000 is operational If the Power LED is not illuminated, it is unlikely the SNE2000 is receiving power, in which case none of the LEDs will be illuminated: Available SDSL Connection Pulsing Green* SDSL connection is established and active Traffic is flowing. Solid Green Problematic SDSL connection A connection exists but there is indication of a problem with the SDSL line.
PAGE 8
Table 4. LEDs (2 of 2) ADDITIONAL INFORMATION LED STATE INDICATION Ethernet Tx Flashing Amber Ethernet activity The SNE2000 is transmitting data across the Ethernet network. Solid Amber Heavy Tx traffic The SNE2000 is transmitting large amounts of data across the Ethernet network. A solid amber Ethernet Tx LED can also signify a lost SDSL connection. Solid Green Ethernet connection is established A solid green Ethernet Lnk LED can also signify a lost SDSL connection.
PAGE 9
RJ45 Pin Assignments SDSL RJ45 Pin Assignments Table 5. SDSL RJ45 Pin Assignments Pin Function 1 not used 2 not used 3 not used 4 Ring 5 Tip 6 not used 7 not used 8 not used Ethernet RJ45 Pin Assignments Table 6.
PAGE 10
! EMI Notices United States – EMI Notice: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
PAGE 11
6. When installed, the product must comply with the applicable Safety Standards and regulatory requirements of the country in which it is installed. If necessary, consult with the appropriate regulatory agencies and inspection authorities to ensure compliance. 7. A rare phenomenon can create a voltage potential between the earth grounds of two or more buildings. If products installed in separate buildings are interconnected, the voltage potential may cause a hazardous condition.
PAGE 12
'" " *SNE2-A2-GN10-00* 12