SPEED-DSL 4.6 Ethernet connection over 4-wires Up to 4.
SPEED-DSL 4.6 Notes Before installing and putting the device into operation, please read the security guidelines at the end of this documentation! Pan Dacom Direkt would like to point out that the information and notes contained in these documents are subject to technical changes. In particular, changes resulting from the continuing development of the products may not have been taken into account. Pan Dacom Direkt does not assume liability for print errors contained in this manual or other inaccuracies.
SPEED-DSL 4.6 CAUTION Pan Dacom Direkt GmbH strongly recommends the use of proper electrostatic discharge (ESD) precautions when handling this equipment. 1. Installation 1.1. Unpack and Inspect the Equipment The following components should be included: 1 SPEED-DSL 4.6 or SPEED-DSL 4.6G 1 power supply 1.2. Power Up the SPEED-DSL 4.6 Plug the power supply into the back of the SPEED-DSL 4.6 and connect it to the power source. Verify that the Power LED on the front of the SPEED-DSL 4.6 is illuminated.
SPEED-DSL 4.6 1.3.1 Bandwidth Switches #1-3: SPEED-DSL 4.6-P and SPEED-DSL 4.6G-P ONLY Switches 1-3 on the SPEED-DSL 4.6-P work in tandem with one another to provide eight bandwidth options for the two SDSL ports; bandwidth for the two ports cannot be configured individually. Distance capabilities listed in the following table assume the use of 26 American Wire Gauge (AWG) cable. Connections made with cable of a lesser gauge (e.g., 24 AWG) will link up at greater distances. Your SPEED-DSL 4.
SPEED-DSL 4.6 1.4. Connect the SDSL Line(s). The primary feature of the SPEED-DSL 4.6 is loop bonding capability, though both the provider and subscriber units can also function with a single SDSL connection. 1.4.1 Loop Bonding Using two SDSL lines for one network connection (loop bonding) will net twice the speed and data passing capability as a single SDSL connection. A second SDSL line can also be considered a backup for the first, and vice versa, should one of the lines become disabled.
SPEED-DSL 4.6 1.5. Connect the Ethernet Line Plug the Ethernet cable into the Ethernet Connection RJ45 port on the back of the SPEEDDSL 4.6. Verify the connection: solid illumination of the Ethernet Connection Lnk LED on the front of the SPEED-DSL 4.6 indicates a link has been established, IF an SDSL connection has already been made.
SPEED-DSL 4.6 2. Additional Information 2.1. LED Indications LED State Indication Additional Information Power solid green unit is If the Power LED is not illuminated, it is operational unlikely that the SPEED-DSL 4.6 is receiving power and therefore none of the LEDs will be illuminated. SDSL pulsing green Connections 1&2 Ethernet Collision SDSL Traffic is flowing.
SPEED-DSL 4.6 Ethernet flashing amber Rx solid amber Ethernet activity The SPEED-DSL 4.6 is receiving data from the Ethernet network. heavy Rx traffic The SPEED-DSL 4.6 is receiving large amounts of data from across the Ethernet network. A solid amber Ethernet Rx LED can also signify a lost SDSL connection when presented as follows (see NOTE on following page): no illumination no activity Either there is no Ethernet link or a link exists but there is no activity.
SPEED-DSL 4.6 Ethernet solid green Lnk no illumination Ethernet A solid green Ethernet Lnk LED can also signify a connection lost SDSL connection; see NOTE below. is established no The Ethernet Rx and Tx LEDs will remain unlit by Ethernet default. connection (A pulsing LED blinks steadily at a rate of once per second. A flashing LED blinks at a more rapid, less constant rate.
SPEED-DSL 4.6 2.2. Regulatory Compliance for Class A Equipment 2.2.1 FCC Regulatory Compliance Information for Class A Equipment This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
SPEED-DSL 4.6 Pan Dacom Networking AG GS Nord Merkurring 105 22143 Hamburg Tel.: 040-679447-0 Fax: 040-67944750 GS Ost Germania Bogen Multimedia-Center 12099 Berlin Tel.: 030-7508-3500 Fax: 030-7508-3535 GS West Schiess Straße 55 40549 Düsseldorf Tel.: 02131-17058-0 Fax: 02131-1705880 GS Mitte/Zentrale Robert-Bosch-Straße 32 63303 Dreieich Tel.: 06103-932-0 Fax: 06103-932400 GS Süd GS Südwest Kurze Straße 40 70794 Filderstadt Tel.
SPEED-DSL 4.6 *220-0000087* *220-0000087* SPEED-DSL 4.6/22.10.
