珠海顶智电子科技有限公司 i5006_OP12 Product Specification Ultra-Low Power 2.4GHZ Wi-Fi +BT5.0 Module (OPL1200) Version Ver1.2 History Document Release Date Version V1.0 2020/09/15 Version V1.1 2021/03/22 Version V1.2 2021/12/22 Modification http://www.qualmodule.
珠海顶智电子科技有限公司 Overview The OPL1200 SoC features a fully integrated 2.4GHz radio transceiver, baseband processor and 8-Mbit of stacked flash for Wi-Fi 802.11b and Bluetooth® Smart applications. The SoC can be used as a standalone application-specific communication processor or as a wireless data link in hosted MCU systems where ultra-low power is critical.
珠海顶智电子科技有限公司 P-192/256 ECDH (Elliptic Curve Diffie-Hellman) Key Generation SHA2 TRNG Power Management Integrated Buck DC-DC converter Supports coin cell and alkaline battery Clock Built-in low power 32KHz RC oscillator and support optional 32KHz crystal.
珠海顶智电子科技有限公司 Block Diagram Pin Description http://www.qualmodule.
珠海顶智电子科技有限公司 Pin Description PIN FUNCTION PIN1 RST_N PIN2 IO5 PIN3 EN PIN4 IO7 PIN5 IO4 PIN6 IO3 PIN7 IO2 PIN8 VDD PIN9 IO23 PIN10 IO10/SCL PIN11 IO11/SDA PIN12 IO12 PIN13 IO18 PIN14 IO19 PIN15 GND PIN16 IO20 PIN17 IO0/TX PIN18 IO1/RX PIN19 IO21 PIN20 IO22 PIN21 IO9/RX PIN22 IO8/TX Description Reset（Low level Reset）,复位（低电平复位） GPIO_5 Power enable(High Level ative),使能复位管脚（高电平有 效） GPIO_7 GPIO_4 GPIO_3 GPIO_2 Power,电源供电输入 GPIO_23 GPIO_10 GPIO_11 GPIO_12 GPIO_18 GPI
珠海顶智电子科技有限公司 ELECTRICAL CHARACTERISTICS Absolute Maximum Ratings Parameter Symbol Min Typ Max Unit Battery Supply VDD_BAT 3.8 V RF LDO Supply DCDC_IN 1.59 V PA Supply VDD_PA 3.8 V OTP Programming Supply VDDQ 2.75 V Digital Core Supply VDD 1.35 V IO Supply VDDO 3.8 V Operating Ambient TO -30 70 ºC Storage Temperature TS -40 125 ºC Junction temperature TJ 125 ºC Max Unit 3.6 V 1.5 V 3.
珠海顶智电子科技有限公司 Adjacent Channel Rejection FER<8%, MPDU = 1024 octets ≥25MHz separation, Pwa nted 35 dB = Psens+6dB, HR/DSSS 11Mb/s, FER<8%, MPDU = 1024 octets Tx Output Power Tx EVM @ Low Power (LP) 0 -2 dBm @ High Power (HP) 8 10 dBm -21 dB DQPSK, peak Bluetooth RF specification LE Receiver Parameter Condition Sensitivity Min Typ Max Unit BLE, 1Mbps, 0.1% BER -80† dBm Max Input Power BLE, 1Mbps, 0.1% BER -20 dBm C/I Co-Channel Pwanted=-67dBm, BLE, 0.
珠海顶智电子科技有限公司 Tx In-Band Spurious Emissions @ 0dBm, foffset=2MHz -53 dBm @ 0dBm, foffset=3MHz -57 dBm @10dBm, foffset=2MHz -41 dBm @10dBm, foffset=3MHz -45 dBm Tx Out-Of-Band Narrowband spurious,30MHz-1GHz 36 dBm Spurious Narrowband spurious, 30 dBm Emissions GHz-12.75GHz -47 dBm Wideband spurious, 30MHz-1GHz -86 dBm Wideband spurious,1GHz-12.75GHz -80 dBm Wideband spurious, 1.8GHz-1.9GHz, -97 dBm -150 150 KHz 50 50 KHz Narrowband spurious, 1.8GHz1.9GHz, 5.15GHz-5.
珠海顶智电子科技有限公司 Federal Communication Commission Statement (FCC, U.S.) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
珠海顶智电子科技有限公司 This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. IMPORTANT NOTES Co-location warning: This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
珠海顶智电子科技有限公司 End product labeling: The final end product must be labeled in a visible area with the following: “Contains Transmitter Module FCC ID: 2ATZK-I5006OP12”. Information that must be placed in the end user manual: The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user's manual of the end product which integrates this module.
珠海顶智电子科技有限公司 Type: PCB Antenna Gain: 1 dBi The module can be used for mobile or applications with a maximum 1dBi antenna. The host manufacturer installing this module into their product must ensure that the final composit product complies with the FCC requirements by a technical assessment or evaluation to the FCC rules, including the transmitter operaition.
珠海顶智电子科技有限公司 Type: PCB Antenna Gain: 1 dBi This device is intended only for host manufacturers under the following conditions: The transmitter module may not be co-located with any other transmitter or antenna; The module shall be only used with the internal antenna(s) that has been originally tested and certified with this module. The antenna must be either permanently attached or employ a ‘unique’ antenna coupler. As long as the conditions above are met, further transmitter test will not be required.
珠海顶智电子科技有限公司 Host manufacturer must perfom test of radiated & conducted emission and spurious emission, etc according to the actual test modes for a stand-alone modular transmitter in a host, as well as for multiple simultaneously transmitting modules or other transmitters in a host product. Only when all the test results of test modes comply with FCC requirements, then the end product can be sold legally. 2.
