Installation Tips
STEP 3: Connecting with RXCamView
STEP 2: Setting Up the Recorder
1. Connect the wireless receiver to
the USB port on the back panel of
the recorder.
2. Connect the recorder to your router
using the included Ethernet cable.
3. Connect the included power
adapter to the recorder. Wait a few
minutes for the system to start
up.
To set up the recorder:
NOTE: The receiver includes double-sided tape and
mounting screws for optional wall mounting for
improved line-of-sight with cameras.
To install your cameras:
1.
Set the mounting bracket in the desired mounting position.
Mark holes through the mounting bracket (shown as
orange X’s on the right).
2. Drill holes where marked for the mounting screws using
the included drill bit .
3. Secure the bracket to the mounting surface
with the included mounting screws (×4). Make
sure all screws are fastened tightly using the
included screwdriver.
NOTES:
• Insert the included drywall anchors if you are
mounting the camera onto drywall.
• The hole at the top of the mounting bracket
will be used in step 5, once the camera is attached
4. Lower the camera base onto
the mounting bracket so
the 2 tabs in the mounting
bracket lock into the 2 slots
in the camera base.
ATTENTION:
This camera includes an Auto Mechanical IR Cut Filter. When the camera changes between Day/Night viewing
modes, an audible clicking noise may be heard from the camera. This clicking is normal, and indicates that the
camerD¿Oter is working.
STEP 4A: Installing the Cameras
Follow the instructions below to mount the cameras. It is recommended that
you refer to the “Installation Tips” section to help you select good mounting
locations.
5. Insert the security screw
through the fasteners on the
top of the camera base and
mounting bracket to secure
the camera to the mounting
bracket. Tighten using the
included screwdriver.
6. OPTIONAL: Tighten the pre-installed locking
screw on the base of the Power Pack using the
included screwdriver.
STEP 4B: Installation Tips
• See images to the right for ideal setup. It is recommended
to place your camera at least 7ft (2.1m) above the ground
and angle it slightly downward toward the monitoring area,
excluding any busy areas (e.g., sidewalks or roadways).
• Ensure the camera image is free of obstructions (i.e., tree
branches).
•
Position the camera no more than 20ft (6.1m) away from
the area you wish to monitor.
•
See the “Optimizing Motion Detection” section to customize
motion settings for each camera on your system.
•
Ensure you have con¿JXred the active area for motion
detection so that only areas of interest are selected. See
the “Optimizing Motion Detection” section for details.
•
For best performance, position the camera so that objects
of interest will move from side-to-side across the camera
image, rather than moving towards or away from the
camera.
Install the camera within range of the recorder (noted in the
camera¶VVSHFL¿Fations).
•
This camera is weather resistant for outdoor use (IP66
Follow the tips below for more accurate motion detection and to optimize battery life:
7. Adjust the angle of the camera:
Charging the Power Pack
Connect the included power adapter to the micro USB port on the
Power Pack.
NOTE: You will need to loosen the locking screw to
remove the Power Pack in the future.
Pairing the Camera
Your cameras should be paired to the recorder and ready to use out of the package. If a
camera becomes unpaired, or if you have purchased a wire-free add-on camera
(max. 6 cameras per system), follow the instructions below.
1. From Live view, tap any free
channel you would like to pair
a camera to (marked with a
icon).
2. Tap PAIR. A timer for 30
seconds appears.
3. Press and hold the pair button on the
back of the camera for 3 seconds.
NOTE: A “pairing successful” message should appear on screen. If you do not see this message,
repeat the steps above.
Optimizing Motion Detection
Customize motion detection settings to ensure motion events are being recorded and
reduce false alarms.
To optimize motion detection:
1.
2. Tap , then tap Remote Setting.
3.
4. Con¿JXre the following as needed:
a. Sensitivity: The amount of motion needed
to trigger recording (e.g., higher sensitivity
requires less motion to trigger recording).
b. Area Selection: Set the active area for
motion detection. Video appears with a red
grid overlayed, meaning the whole image is
active. Tap red squares to disable motion
detection in those areas (see example image
to the right). Tap SaveZKHQ¿QLVKHG
TIP: Disable areas that will trigger unwanted
motion events, like busy streets or trees and shrubs that will move in the wind.
c. Distance Setting: Con¿JXre distance setting for motion detection. While watching
the camera’s video on your mobile device, recreate a motion event in front of your
camera. The icon will change from
to when motion is detected by the camera.
Change the distance setting if motion detection is being triggered by unwanted
events.
NOTE: Distance will be affected by temperature.
d. Buzzer: Set the recorder to sound an alarm when motion is detected.
5. Tap SaveZKHQ¿QLVKHGRepeat for other cameras on the system.
to the mounting plate.
rated). Installation in a sheltered location is recommended.
•
Battery life will vary based on temperature, settings and number of events.
8. Use the included cable clips to complete the installation.
Power cable
Mounting
surface
NOTE: The Power PDFN/('ÀDVKHVred while outside the safe charging
temperature of 32-113°F (0-45°C). In this state, the camera remains
powered up, but the Power Pack will not charge outside the safe
temperature range.
To connect with RXCamView :
1. Download and install the free RXCamView app from the
App Store or Google Play Store.
2. Tap the RXCamView icon to launch the app.
Connect to your system using the free
RXCamView app for smartphones and
tablets (iOS and Android).
3. Tap to open the menu. Tap Device, then tap .
5. Your cameras will appear on the Live screen of the app. Tap the play
button (
) to stream live video on channels that are in sleep mode.
Ini etup is no ete! T ctions on
4. Enter the following:
A
B
C
D
E
F
Ensure Device ID is selected.
Tap to scan the QR code on the back
of your recorder using the camera on
your mobile device.
Ensure the Client Port reads 9000 .
Enter the username (default: admin).
Enter the password (default: empty).
Tap Save.
Twist the
adjustment ring
counterclockwise
to reposition the
camera. Tighten
the adjustment
ULQJZKHQ¿QLVKHG
Camera
levelling
Arm
rotation
Arm
angling
Use the included
Allen Key
to loosen
the adjustment
screws labelled
below. Tighten all
adjustment screws
ZKHQ¿QLVKHG
IPC-A
IPC-A
IPC-A
IPC-B
IPC-B
IPC-B
LED Color Meaning
Green
Fully charged
Red
Currently charging
Power Pack Charge Time
2-cell
Approx. 6 hours
3-cell
Approx. 8 hours
Launch the RXCamView app.
8.6
”
0.16
”
210
mm
2.5
”
64mm
6.7”
170mm
4mm
NVR-B
NVR-A
1. Connect the recorder to your router
using
Ethernet cable.
2. Connect the included power adapter
to the recorder.
Quick Connection Guide
STEP 1: Initial Setup
To prepare the cameras:
Before you begin, you will need to prepare the wire-free cameras and Power
Packs.
NOTE: Power Packs come fully charged with no need for initial charging.
Attach an antenna to each camera.
For IPC-A / IPC-B Series cameras,
twist the adjustment ring counterclockwise
to reposition each camera as shown to the
right. Twist clockwise to tighten when finished.
Peel off the PLEASE REMOVE label covering the
contacts on each Power Pack. Insert the charged
Power Packs into each camera base. Push up until
the Power Pack ‘clicks’ into place.
3. Connect the two black antennas to the
wireless receiver.
IPC-A
IPC-B
1.
2.
Dimensions
1.9”
48mm
8.2”
208mm
11.8”
300mm
5.5”
134mm
2.9”
73mm
6.6”
168mm
IPC-A
IPC-B
NVR-B only
NVR-B
NVR-A
3.5”
89mm
2.9”
73mm
5.0”
126mm
Adjustment
ring
Adjustment
ring
Select a device, then tap Motion.
Wireless Camera
RS-CH222H1CGA-WL-36W