Specifications

e - 2 S
tarting problems. Contact your dealer.
e - 5 Tipping-over protection. Re-ignite the heater.
e - 6 Poor burning. Contact your dealer.
e - 7 Room temperature If necessary,
above 32°C. re-ignite the heater.
e - 8 D
efective booster. Contact your dealer.
e - 9 Air filter dirty; or Clean filter
Fuel pump dirty. Contact your dealer.
The heater has been in operation
continuously for a period of 65 hours
and has turned itself off automatically. Switch the heater back on.
-- : -- Out of fuel. Refill removable tank.
(& blinking
FUEL-light)
-- : -- Too little ventilation. Ventilate better.
(& blinking
VENT
-light)
Always contact your Zibro dealer for any malfunctioning not listed above.
AUTOMATIC DEACTIVATION
This heater is fitted with a safety system that ensures that it switches off
automatically after 65 hours continuous operation. The following will then appear
in the display: . If desired, you can switch the heater on again by pressing
the button
M (see section D).
AUTOMATIC CLEANING MODE
When the heater has been burning continuously for two hours at its highest
setting, the burner will automatically start an autoclean procedure. The display
will show the autocleaning code
cl:05 running back to cl:01. The procedure takes 5
minutes, during which the heater will burn at its lowest setting, while the burner
autocleans. When the burner is clean again, the heater will automatically switch
back to the highest setting again.
I CHILDPROOF LOCK
The childproof lock can be used to prevent children accidentally changing the
heater settings. When the heater is burning and the childproof lock is on, the
heater can only be switched off. Other functions are blocked then. If the heater
has already been switched off, the childproof lock also prevents accidental
ignition of the heater.
Activate the childproof lock by pressing the appropriate key
N and holding it down for more than 3 seconds. The KEY-LOCK indicator light will
light up (Fig. I), indicating that the childproof lock has been activated. Switch off
the childproof lock by pressing the key
N and holding it down for more than 3
seconds once again.
J THE CORRECT USE OF 'SAVE'
The 'SA
VE' function allows you to limit the temperature. When this function is
activated, the heater will automatically switch off, when the room temperature
exceeds the set temperature by 3°C. Subsequently, when the room temperature has
dropped again to the set temperature, the heater will automatically switch on again.
Activate the 'SA
VE' setting by pr
essing the appr
opriate
Q key
. The SA
VE indicator
light will light up (Fig. J). Switch of
f the function by pr
essing the SAVE key once
again.
4
48
s
a
v
e
t
i
m
e
r
h
o
u
r
m
i
n
.
k
e
y
-
l
o
c
k
s
a
v
e
t
i
m
e
r
v
e
n
t
.
f
u
e
l
c l 0 5
set room
temp.
clock

I: When the KEY-LOCK
light lights up, the
childproof lock has been
activated.
J: When the SAVE light
lights up, the heater will
automatically switch on
or off in order to remain
within a specified
temperature range.
s
a
v
e
t
i
m
e
r
h
o
u
r
m
i
n
.
k
e
y
-
l
o
c
k
s
a
v
e
t
i
m
e
r
v
e
n
t
.
f
u
e
l
set room
temp.
clock

s
a
v
e
t
i
m
e
r
h
o
u
r
m
i
n
.
k
e
y
-
l
o
c
k
s
a
v
e
t
i
m
e
r
v
e
n
t
.
f
u
e
l
2 0 : 1 5
set room
temp.
clock

s
a
v
e
t
i
m
e
r
h
o
u
r
m
i
n
.
k
e
y
-
l
o
c
k
s
a
v
e
t
i
m
e
r
v
e
n
t
.
f
u
e
l
2 0 : 1 5
set room
temp.
clock
