Quick Installation Guide

ManualsBrandsZIONCOM ELECTRONICS ManualsSmart HomeAC1200 Dual Band Smart Home Wi-Fi System

AC1200 Dual Band Smart Home Wi-Fi System

Appearance

Connect the Master router to the Internet

Create the Seamless Mesh Wi-Fi System

2.2. Configure the Master router on Phone

2.1. Diagram of a Master’s network

Model: T6

Website: http://www.totolink.net

Information in this document is subject to change without prior notice.

Master router and Satellite router have been paired successfully as

the factory default setting. (It doesn’t need any configurations on

the Satellite router.)

Master router and Satellite router can be recognized from the label

stuck on the bottom of the router.

Front Panel

State LED

(Recessed)

T Button

LED Status

Button/Ports

T Button

LAN Ports

WAN Port

DC Power Port

Description

Solid Green

Blinking Green

Blinking between Red and Orange

Solid Orange(Satellite Router)

Solid Red(Satellite Router)

Blinking Red

The router is booting. It takes about 40 second, and after that

the LED color will become blinking Green.

Satellite router is synced with Master router successfully. And

the signal is good.

Router finishes the booting and is working normally.

The sync is being processed between Master router and

Satellite router.

Satellite router is synced with the Master router successfully,

but the signal is not very good.

Satellite router failed to sync with the Master Router.

The reset process is being proceeded.

Reset the router to factory settings. Press and hold the “T” button for 8-10

seconds(LED will blink Red) to reset the router.

Confirm the Master router and activate the “Mesh”. Press and hold the “T”

button until LED blinks between Orange and Red(about 1-2 seconds) to activate

the “Mesh” function on the Master router.

Connect to PCs or Switches with RJ45 cable.

Connect to the Modem or connect the Ethernet cable from ISP.

Used as a LAN pot in the Bridge, Repeater, WISP operation mode, or on the

Satellite router in the Mesh Wi-Fi system.

Connect to the power source.

Master Router Back Panel

Satellite Router Back Panel

LAN Ports

WAN Port

DC Power Port

3.1 Diagrams of the Mesh Wi-Fi system

FAQs

FCC warning:

This equipment has been tested and found to comply with the limits for a

Class B digital device,pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses and can radi-

ate radio frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio communic-

ations. However, there is no guarantee that interference will not occur in a

RF Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an un-

controlled environment .

This transmitter must not be co-located or operating in conjunction with any other

antenna or transmitter.

This equipment should be installed and operated with minimum distance 20cm

between the radiator& your body.

Manufacturer: ZIONCOM ELECTRONICS (SHENZHEN) LTD.

Address: Room 702, Unit D, 4 Building Shenzhen Software Industry Base, Xuefu

Road, Nanshan District, Shenzhen, Guangdong, China

Internet

Router (Master)

Power adapter

Outlet

Smartphone

Tablet

Connect the Wi-Fi of the router with your Phone, then run any

Web browser and enter http://itotolink.net

(Tips: 8196D1 and 8196C1 on the SSID represent the last 6

numbers/letters from the MAC address, here we take them as

an example, they are different in any other routers.)

TOTOLINK_5G_8196C1

TOTOLINK_8196D1

Click Quick Setup on the coming page.

Input admin for both User Name and

Password on the coming page, then

click Login.

admin

http://itotolink.net

Internet Setting. Choose a suitable WAN

Connection type from the list, and fill in

the information required.

WAN Connection Type Description

Static IP

Input the IP address, Subnet Mask,

Default Gateway, DNS from your ISP.

DHCP

No information required. Please confirm

with your ISP if DHCP is supported.

PPPoE

Input User Name and Password from

your ISP.

http://itotolink.net

Model No: T6

After configured the Master router, please relocate the satellite routers to

a suitable place to finish the Mesh Wi-Fi system. One T6 master router

supports to pair with max 4 satellite routers, but pairing with 1 or 2

satellite routers is the recommended solution.

Master

Satellite

Master

Satellite

Mesh Wi-Fi System of 1

Master Router and 2

Satellite Routers

Mesh Wi-Fi System of 1 Master Router and 1 Satellite Router

3.2 Relocate the Satellite router

Power on the Satellite routers within the wireless coverage of the Master

router and adjust the positions of the Satellite routers to achieve the best

signal according to the LED colors on the “T” button.

Green color indicates the signal is good. Yellow color indicates the sig-

nal is not good enough, please close the Satellite router to the Master

router until the color turns Green. Red color indicates the signal is bad

or not successfully connected with the Master router, please close the

Satellite router to the Master router until the color turns Green.(If it doesn’t

work, reset the router and try again.

1. Unable to log in the router's web page on Phone?

Please check if your Phone has connected to the Wi-Fi of the

router and make sure you have entered the correct default

gateway http://itotolink.net

2. How to reset the router to factory default settings?

Keep the router powered on, then press and hold the RST button

(for about 5-8 seconds) until System indicator becomes blinking

light quickly.

3. How to do if I want to add a new Satellite router to

the existing Mesh Wi-Fi system?

Keep the Satellite router as the factory default setting(If uncertain, pl-

ease reset the router) and then power on the Satellite router within the

wireless coverage of the Master router. It will pair with the existing

Master router automatically.

particular installation. If this equipment does cause harmful interference to radio

or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more

of the following measures:

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference

(2) This device must accept any interference received, including interference that

may cause undesired operation.

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help.

Any Changes or modifications not expressly approved by

the party responsible for

user’s authority to operate

the equipment.

compliance could void the