Assembly Instructions

ManualsBrandsZipcode Design ManualsBedsOleanna Low Profile Storage Platform Bed

Table Of Contents

Double Platform

Storage Bed

Required Tools

Screwdrivers

Flat Head

Using a power screwdriver

will speed up assembly.

Caution

Do not over tighten any screw.

The last few turns of each screw

should be done very slowly or by hand.

Phillips Head

Optional Tools

DATE STAMP

Assembly Instructions

• For help with assembly

• If you have received a damaged or

We will process replacement parts

UPS Ground or mail.

Before you call please:

2) Note the

3) Review the contents of your shipment to

determine what you are missing. This unit

is shipped in 3 cartons. Make sure you

have received all cartons.

in 2

business days or less. Parts are shipped via

1) Record the following information from the

shipping label on the outside of the box.

You will need it for warranty purposes:

• Ship To Name

• Sales Order Number

product model number.

Hammer

This product is shipped in

3 cartons

Make sure you have all cartons.

Sometimes cartons shipped on the same

day get separated and are delivered on

different days.

1 of 3

2 of 3

3 of 3

Online Option:

Fill out the Replacement Parts Order form in the Product

defective part or are missing hardware.

Summary of content (20 pages)

PAGE 1
Double Platform Storage Bed Assembly Instructions DATE STAMP This product is shipped in 3 cartons 1 of 3 2 of 3 + 3 of 3 + Make sure you have all cartons. Sometimes cartons shipped on the same day get separated and are delivered on different days. • For help with assembly • If you have received a damaged or defective part or are missing hardware. We will process replacement parts in 2 business days or less. Parts are shipped via UPS Ground or mail.
PAGE 2
Hardware Identification Bed Hardware JRN Nut (24) RM-0312 Drawer Slides for Bed JCB Connector (24) RM-0310 bronze (cherry / espresso/walnut) RM-0311 chrome (white / maple) RM-0314 black Allen Key (1) RM-0313 T Spacer (24) RM-0628 Drawer Slide Screw (90) RM-0074 Drawer Bottom Stabilizer (6) RM-0839 LEFT Slide (6) RIGHT Slide (6) Drawer Hardware 1 LEFT Drawer Slide per Drawer (Total = 6) 1 RIGHT Drawer Slide per Drawer (Total = 6) 5 per drawer 4 per drawer #8 - 1½” Hi Lo Screws (24) RM-0504 12
PAGE 3
Bed Parts B5 B6 B1 B3 B2 B4 B2 B1 B3 B4 B1 Outer Gables (2) black espresso warm cherry B2 B3 B4 Inner Gables (2) black espresso warm cherry Upper Stabilizer (2) black espresso warm cherry Lower Stabilizer (2) black espresso warm cherry B5 Plywood Slats (8) B6 Metal U-channel (2) Page 3 of 20
PAGE 4
STEP 1 Estimated Time: 10 minutes Attach metal U-channels to each outer gable using drawer slide screws Drawer Slide Screw B1 STEP 2 B1 Estimated Time: 15 minutes Attach T spacers to outer gables with drawer slide screws.
PAGE 5
STEP 3 Estimated Time: 10 minutes Attach drawer glides to T-spacers on outer gables as shown in the photo Position the Drawer Glides with: A) The wheel at the finished side B) The wheel on the unfinished bottom Finished Side Bottom Use 14th hole Use 1st hole Use 1st hole Use 14th hole Page 5 of 20
PAGE 6
STEP 4 Estimated Time: 5 minutes Insert JRN nuts into the holes on each end of the inner gables. The holes are drilled through. You can insert them from either side. B2 B2 Insert the nut as shown, so that the hole lines up with the hole on the edge of the gable.
PAGE 7
STEP 5 Estimated Time: 5 minutes Insert JRN nuts into the holes on each end of the upper (B3) and lower (B4) stabilizers.
PAGE 8
STEP 6 Estimated Time: 10 minutes Attach “T” spacers and drawer glides to Inner Gables 4” Bottom 6a Attach “T” spacers to ONE side of each inner gable with drawer slide screws Drawer Slide Screw IMPORTANT: 6b Attach drawer glides to “T” spacers on inner gables. Position the drawer glides with: A) The wheel at the finished edge B) The wheel on the bottom Before attaching the drawer glides, determine the TOP and BOTTOM of each inner gable. A.
PAGE 9
STEP 7 Estimated Time: 5 minutes Using JCB connectors, and the Allen Key provided, attach each lower stabilizer (B4), one at a time, to both inner gables B4 B4 Finished edge IMPORTANT Identifying the Lower Stabilizer The screw hole is at the top, close to the finished edge JCB Connector JRN Nut If you have any difficulty tightening the JCB connector, use a screwdriver to adjust the JRN nut to make sure the hole is facing the opening for the connector Page 9 of 20
PAGE 10
STEP 8 Estimated Time: 5 minutes Using JCB connectors, attach each upper stabilizer (B3), one at a time, to both inner gables.
PAGE 11
STEP 9 Estimated Time: 10 minutes Attach one outer gable to stabilizers with JCB connectors B1 Page 11 of 20
PAGE 12
STEP 10 Estimated Time: 5 minutes 10a Spread the wooden slats out across the inner stabilizers 10b Slide the slats into the wide spaces of the metal U-channel (B6) on one outer gable.
PAGE 13
STEP 11 Estimated Time: 10 minutes Attach second outer gable to stabilizers with JCB connectors 11a Secure the gable in place with connectors, but don’t fully tighten 11b Ensure the slats are set inside the u-channel and that they haven’t pulled out of the first outer gable.
PAGE 14
Drawer Parts Identification D4 D2 D1 D5 Drawer Front (6) black espresso walnut D3 D1 D2 Left Drawer Side (6) Plywood D3 D4 Right Drawer Side (6) Drawer Back (6) unfinished D5 Drawer Bottom (6) unfinished Plywood STEP 12 12a Estimated Time: 5 minutes PER DRAWER Insert cams into drawer sides D2 D3 Right Drawer Side Left Drawer Side Make sure arrow faces toward hole for twister dowel Page 14 of 20
PAGE 15
12b Screw black twister dowels into drawer fronts D1 To see a video showing how the cam and connectors work, please visit our website ONLINE HELP binedrawer t Pasides rts toIddrawer entifback 12cCaAttach icawith tio1½” n Hi Lo screws 1½” Hi Lo Screws Page 15 of 20
PAGE 16
12d Attach drawer front and tighten cams using a flat head screwdriver Left Drawer Side Unlocked 12e Right Drawer Side Locked Turn 210° Unlocked Locked Turn 210° Turn drawer upside down and slide drawer bottom into grooves Page 16 of 20
PAGE 17
12f Secure the drawer bottom to the drawer back with nails C Use 4 nails per drawer 12g Insert the Drawer Bottom Stabilizer Position the Stabilizer in the center of the drawer and insert it into the groove on the drawer front. This is the same groove that you inserted the drawer bottom into.
PAGE 18
12h Attach drawer slides to left and right drawer sides using drawer slide screws Right Drawer Side Drawer Slide Screws Left Drawer Side Drawer Slide Screws Page 18 of 20
PAGE 19
STEP 13 Estimated Time: 2 minutes Insert drawers Note: When drawers are installed correctly, you will not be able to remove them without first lifting up the drawer front.
PAGE 20