LIST OF SCREWS AND TOOLS PART QTY. El B DI El D Ill ITEM PART QTY. 3 6X35 MM 0)mmmmmmim 12 4X35 MM @JOllllllllt> 24 3X15 MM � 8 4X20 MM @)mmnIB 16 6X40 MM 0)-)-)))) 48 4X14 MM � El El D -El ITEM 8 4X16 MM � 4 6X12 MM @mm 4 4X4 MM @JID 3
u This unit uses cam bolts and locks. The following explains how to use them. This is not an assembly step; it is a guide for when you are actually doing the assembly using this kind of hardware. CamBolt � Cam Lock 1. Screw the bolt into the corresponding panel. ' ' 2. In the other panel, insert the cam lock and align it so it can properly receive the bolt, then join both panels. There might be a ver small gap between the panels which is normal. ALIGNMENT DIRECTION 3.
BEFORE YOU START THE ASSEMBLY, PLEASE READ THE FOLLOWING TIPS AND WARNINGS. • 0 Do a quick inventory to 8 To avoid misalignments, 8 Missing, damaged and C, Do not overtighten or 8 The replacement parts service 8 Sometimes the laminate might cover partially or make sure the package contains all the parts and hardware listed in the assembly instructions. always leave the screws loose and tighten them until all pieces are positioned correctly. defective parts can be replaced at no cost to you.
P.7 ASSEMBLY STEPS STEP 1 ------Screws: First screw the bolts K into the back face of the small drawer front panel 27, then assemble the drawer side panels 25 and 26 as shown and as explained in page 5. 6x25mm x4 � Cam lock direction 2nd Don't forget to � tum the cam-lo �IL" � STEP2 Slide the drawer bottom panel 28 through the groves of panels 25, 26 and 27 as shown.
P.8 STEPS ------Screws: 4x20mm � Assemble the handle 24 to the small drawer front panel 27 using screws Das shown. x2 REPEAT STEPS 1 THRU 5 TO ASSEMBLE THE SECOND SMALL DRAWER First screw the bolts K into the back face of the file drawer front panel 32, then assemble STEP6 ------- the file drawer side panels 30 and 31 as shown and as explained in page 5.
P.9 STEP10 Grab the last SET of drawer sliders 14, and sort them by their shape: ------- - The "L" shaped will be used in this step. Screws: 3x15mm � x4 - The flat ones will be used until step 25, so please set them aside. With the drawer upside-down and its front facing away from you, assemble the "L" shaped sliders using screws C as shown. ATTENTION: VERY IMPORTANT! Correct Incorrect 1Lr---J .. f LJ STEP11 Assemble the handle 24 to the ------- front panel 32 using screws Das shown.
P.10 STEP15 ------Screws: First screw the smaller bolts K to the back end of the panel 4, then screw the longer bolts Eon the sides as shown. Attention: The Innermost holes are for the wooden pins of panels 1 and 2 in next step. 6x25mm x2 � 6x40mm l:1-)-)))) x4 r , � X4 (For the 1st and 4th holes on the sides) STEP16 Assemble the CPU panels 1 - 2 - 5 to the CPU bottom panel 4 as shown and explained in page 5. Troubleshoots: Problem: The panels don't come down flush and there is a gap.
P.11 STEP19 Assemble the base tubes 7 to Screws: cabinet bottom panel 11 using screws F as shown. 4x14mm � Attach the studs 3 to the base tubes 7 as shown. STEP20 ------- the bottom face of the file x16 STEP21 ------Screws: 3x15mm (t}1:nnu>- x8 (This panel is wider than panel 4) With the cabinet side panels 12 and 13 oriented as shown, assemble 2 sets of the flat sliders 14 to the top and middle sets of holes using screws C as shown.
P.12 STEP 23 ------Screws: First screw the smaller bolts K to the back end of the panel 11, then screw the longer bolts E on the sides as shown. Finally, assemble the panels 12, 13 and 15 as shown and as explained in page 5. Attention: The innermost holes are (For the 2 for the wooden pins � -.:JI back holes) of panels 12 and 13.
P.13 STEP 25 ------Screws: Assemble the last set of flat sliders 14 to the bottom sets of holes on the side panels 12 and 13 using screws C as shown. Note that the wheel is facing towards the front of the panels and down with 2 empty holes ( on the slider) above it.
P.14 STEP 28 Use screws H to assemble the slider bases 21 to the back face of the main panel 18, with the bases oriented towards the outside as shown. Screws: 6x12 mm @an x4 Bases are oriented towards the outside ;........ :� \ :,,,,,-··. ·[ ·: --,\., , \ \-. STEP 29 ------Screws: 4x4mm @nn x4 I - ........ ... ... - ..... ,, ,,' .. .., .. .. .. :' .. .. .. .. ._ 'ii: I wEl ' Use screws I to assemble the keyboard sliders 20 to the slider bases 21 as shown.
P.15 STEP 30 ------place the main panel over the frame, making sure the bolts enter into the holes of the back First screw bolts K to the main panel 18 as shown. Then with the help of another person, Screws: panels 5 and 15, BUT DO NOT LOCK THE CAM LOCKS YET. Then place plastic washers J over the holes of the cabinets, and secure the support tubes 6x35mm x3 19 using screws A from underneath the frame. Finally, lock the cam locks as explained in page 5.
P.16 STEP 32 ------Screws: 4x16mm � Use screws G to assemble the hinges 8 to the CPU door 23. STEP 33 ------Screws: Use screws D to assemble the handle 24 to the CPU door 23. 4x20mm $)llIDIDIDlID x2 x4 ....... ·· ·· --� ···• ···· · STEP 34 Use screws G to assemble the hinges 8 on the CPU door 23 to the CPU left panel 1 as ------- shown. Screws: 4x16mm (f)nttt> ...................................................
P.17 STEP 35 Insert the drawers into the cabinet, starting with the bottom drawer. For the top drawer, you might have to insert it at a downward tilted angle. The wheel on the drawer will run in the middle of the sliders on the cabinet. Troubleshoot: Problem: There is a gap at the bottom of the file drawer and/or the top drawer doesn't fit. Reason: The drawers sliders are rising the drawers more than what it should be.
I!\ ALL DONE! Give yourself a nice pat on the back.
P.19 AFTER THE ASSEMBLY IS DONE, PLEASE READ CAREFULLY THE FOLLOWING CARE AND MAINTENANCE WARNINGS: MAXIMUM WEIGHT CAPACITIES (DO NOT EXCEED THESE LIMITS) 22 Lbs------L--::� -- e-+++-- 22 Lbs • Do not exceed the indicated weight limits. • Do not expose the surfaces to direct sunlight or to extreme environmental conditions. • Clean the surfaces preferable with a clean cloth damped in a solution of mild soap and water, then dry with a clean towel.
DESKS/LAPTOP CARTS/FILE CABINETS: LIMITED 5-YEAR WARRANTY TV Stand/Entertainment Center : 2 YEAR WARRANTY We warrants to the Original Purchaser who acquired a new product or its authorized resellers that this product will be free from defects in its workmanship and materials, under normal use and service conditions, as described herein. "Defects" as used in this warranty, is defined as any imperfections that impair the use of the furniture or product.
