ZIPLEVEL SYSTEM CONCEPT INTRODUCTION +20’ (6m) 200’ (60m) CIRCLE Unipod Measurement Module* Base Unit Cord SINGLE SET-UP RANGES -20’ (6m) *Zero at any reference within range You’re about to enter an exciting new labor saving world of elevation measurement and leveling. The ZIPLEVEL® PRO-2000 High Precision Altimeter lets you focus on your work rather than the tedious task of measuring your work.
INTRODUCTION Use any of ZIPLEVEL’s 16 powerful built-in functions to master tough elevation measuring and leveling tasks from estimating, planning, excavation, construction and landscaping to fabrication, checking and analysis. Attach the optional PC Serial Link to ZIPLEVEL’s built-in Serial Port and make ZIPLEVEL® a powerful data gathering instrument capable of downloading stored measurements to a Personal Computer for analysis and tabulation or plots of profiles, sections and topographical maps.
1 ▪ ZIPLEVEL BASICS ZIPLEVEL® consists of a Base Unit (BU) and hand-held Measurement Module (MM) joined by a rugged wireless Cord that communicates elevation data from the BU to the MM. Stakes secure the Base Unit on unstable terrain. A Unipod eliminates constant bending for multiple readings and doubles as a vertical calibration standard when fully extended. All components are stored in the Base Unit when not in use. To use ZIPLEVEL: ZIPLEVEL PARTS ▪ 2 To remove the boot: 1. Place against chest 2.
3 ▪ MEASUREMENT MODULE Use the Measurement Module to level and take readings. The bottom and back of the Module are the only sides that may be used interchangeably for measurements. You may use other sides only if you first zero on that side. Hold the Module level and measure near the center of the side in use. Do not zero the Module and then invert it without correcting the reading as shown in the illustration on the next page.
5 ▪ KEYPAD Use the keypad on the Measurement Module to control the ZIPLEVEL® and take readings. The most frequently used functions, called labeled functions, are printed on the eight keys below the display. ZIPLEVEL’s more advanced or less frequently used functions, called hidden functions, may be accessed by logical combinations of two or more keys. All keys except the HOLD and ON/OFF keys must be pressed and held for two seconds to activate. This minimizes accidental operation of the functions.
▪ QUICK START Most ZIPLEVEL® users will use only those functions routinely necessary in their work. We suggest that you try all ZIPLEVEL® functions at least once to become familiar with its capabilities. This Quick Start will help you gain confidence by using a few frequently used functions: 1. Raise the lower door of the Base Unit, remove the Measurement Module and lay the Base Unit on its back on the floor or ground. The Base Unit should be secure but need not be level. 2.
9 ▪ LABELED FUNCTIONS This section describes how to operate ZIPLEVEL’s labeled functions. Glance through all the functions and illustrations then try each function on the ZIPLEVEL®. HOLD & ZERO ▪ 10 HOLD Press HOLD before the Module is in position - the reading will lock on the display when movement stops. Display not visible ZERO here first ON/OFF Momentarily press to turn ZIPLEVEL® on or off.
11 ▪ SCALE & RESOLUTION RES Press 2 seconds to enter and continue to press or press and release to select the desired measurement RESolution (measurement precision). Lower resolution (larger values or increments) provides faster readings for rough grade or estimates.
13 ▪ CALIBRATION Unlike rotary lasers and optical levels, the ZIPLEVEL® is not tilt sensitive, its level plane does not develop tilt error and it does not amplify error with distance or require factory calibration. The CAL function lets you calibrate vertical measurement accuracy much like calibrating the vertical sight rod of a rotary laser. Calibration may be needed for accurate vertical measurements but is not required for leveling operations.
15 ▪ RECORD The RECord function eliminates extensive tabulation and computation required to average large numbers of readings. Now you can easily estimate the slurry necessary to level an uneven concrete surface, the fill needed below concrete or predict the graded level of a hilly lot (see illustrations).
17 ▪ MARK The MARK function lets you create audible tones: 1) at a selected elevation, 2) for elevations within a selected band, or 3) elevations outside a selected band. Tones may be set over ZIPLEVEL’s full vertical single setup range.
19 ▪ HIDDEN FUNCTIONS TEMPERATURE To display ambient temperature, continue to press ON/OFF for 2 seconds when turning ON. Momentarily press any other key to exit temperature. HIGH PRECISION The High Precision function lets you measure with an unprecedented paper thin 0.005” (0.1mm) internal precision over a vertical range of 4’ (1.2m).
21 ▪ CARRY The CARRY function lets you leap-frog the Measurement Module and Base Unit to measure elevations (differential level) over any distance or elevation on earth without tabulation, computations or loss of your original benchmark plane. Two people working together can traverse terrain at a 2 mph (3 kph) rate. To use the CARRY function follow the steps in the illustration. Repeat the HOLD and ZERO sequence over any distance or elevation.
23 ▪ RECORD DATA ZIPLEVEL® can be used to record measurement data for creating tables, profiles, sections, contour or 3D maps. Press REC and MARK together for 2 seconds to enter or exit. REC will be flashing on the display while in the Record Data function. Press REC and ZERO together for 2 seconds to clear all data. Press HOLD momentarily to record each measurement.
25 ▪ INSPECT/DUMP & INITIALIZE INSPECT or DUMP These functions allow inspection of Record Data registers and/or data transfer to a PC. To use this function: Press and hold CAL and REC keys together for two seconds to INSPECT data. Momentarily press the MARK key to sequence up through positions. Momentarily press the REC key to sequence down through positions. To sequence up or down in multiples of ten positions, momentarily press the HOLD key for up and CAL key for down.
27 ▪ ELEVATION Elevation lets you preset the display and Carry reference plane to a benchmark elevation in engineers (FT) or metric scales for use in the CARRY function. You may preset the ELEV function to zero by pressing MARK and ZERO together for 2 seconds before entering the ELEV function. To enter or exit the ELEV function, press and hold the SCALE and RES keys together for 2 seconds.
29 ▪ MONITOR The Monitor function can be used to keep the ZIPLEVEL® from shutting off during periods of inactivity. It also can be used with the optional PC Serial Link for remote monitoring or data logging. For example, place the Base Unit on a Styrofoam® float to log water tank or river levels. To enter the MONITOR function, press and hold the ON/OFF and CAL keys together for two seconds when turning on ZIPLEVEL®. To exit, turn the unit off.
31 ▪ USE TIPS 1) Secure the Base Unit after removing the Measurement Module. 2) Extend the Unipod from the top down and retract from the bottom up (see page 14). Always gently tighten bushings (avoid over-tightening). 3) Hold the Measurement Module in the handgrip areas to the right and beneath the keypad. For single handed operation, use the thumb to press the most frequently used buttons: ON/OFF, HOLD and ZERO. The left hand can manipulate the Cord. Release or hold steady while reading (see page 8).
33 ▪ HOW TO MEASURE ACCURATELY ZIPLEVEL CARE ▪ 34 6) Always secure the Base Unit to prevent movement during measurements – it does not need to be level. ZIPLEVEL® is rugged, durable and designed to provide years of reliable performance when properly used. Here are some guidelines: 7) Avoid using ZIPLEVEL® beyond the specified ranges of elevation or temperature.
35 ▪ ZIPLEVEL CARE 6) Pack up the ZIPLEVEL® when not in use for extended periods of time. Never leave out in foul weather or overnight. Avoid storage inside a hot closed vehicle or trunk. 7) ZIPLEVEL® contains a non-toxic biodegradable clear liquid. In the unlikely event that a damaged unit releases liquid or if the Cord is cut, bend over Cord and wrap with tape or wire to stop liquid release. Wipe up liquid with absorbent towels, remove residue with soap and water and return to factory for service.
37 ▪ MAINTENANCE/PRODUCT ASSISTANCE Technidea Corporation warrants the ZIPLEVEL® PRO-2000 High Precision Altimeter against deficiencies in materials and workmanship for one year from the date of purchase. The ZIPLEVEL® hydro-pneumatics are covered by a second year pro-rata warranty. ZIPLEVEL® never requires factory calibration and normal use should allow years of use without repair.