Installation Guide

ManualsBrandsZippity Outdoor Products ManualsFencing3-1/2 ft. x 2-5/8 ft. Newport Vinyl Picket Fence Gate with Stainless Steel Hardware

www.zippity-outdoor.com

ASSEMBLY

INSTRUCTIONS

NEWPORT VINYL PICKET GATE

(31” H X 41” W)

60 MIN

Approximate assembly

time

42 in Opening

1/2 in 1/2 in

33 1/2 in

2 in

41 in Gate Width

This gate can easily be trimmed down

horizontally to t your custom fence. Use

ne-toothed circular saw or hack saw.

This gate is designed to be used with our Newport Vinyl Picket Fence.

6935 Reames Rd. Ste. K. Charlotte, NC 28216

support@zippity-outdoor.com

704-892-5222 / 877-234-6196

zippity-outdoor.com

Want to see a video on how to

assemble this product? Scan

the code below!

Ver. 072320

Summary of content (10 pages)

PAGE 1
ASSEMBLY INSTRUCTIONS This gate is designed to be used with our Newport Vinyl Picket Fence. 33 1/2 in 1/2 in This gate can easily be trimmed down horizontally to fit your custom fence. Use fine-toothed circular saw or hack saw. 60 MIN 1/2 in 41 in Gate Width 42 in Opening NEWPORT VINYL PICKET GATE (31” H X 41” W) Approximate assembly time 6935 Reames Rd. Ste. K. Charlotte, NC 28216 @ 2 in Want to see a video on how to assemble this product? Scan the code below! support@zippity-outdoor.
PAGE 2
GENERAL INFORMATION IMPORTANT • Please read through before starting assembly. • Important: Check the inside of the larger pieces in your box for other materials packed inside. • When assembling components, place on a non-abrasive surface (i.e. shipping box) to avoid scratching. • We recommend an area approximately 5’x 8’ for unobstructed assembling. • You should not need to use excessive force when assembling components.
PAGE 3
GENERAL INFORMATION 1. Read over fence instructions first. Your gate and fence will work better together if you first take the time to read and understand your fence. 2. Pre-Assemble the gate frame. Please do not screw the gate frame together until you have temporarily assembled the gate frame. In other words, do a dry run first. This will ensure: 1. That you have everything necessary to complete the gate. 2. That you will have assembled the gate frame in the correct order. 3.
PAGE 4
STEP 1: LAY OUT MATERIALS A B G Note: Top rail has picket holes on both sides. Top Gate Bracket (2) C Top Rail (1) 1½” x 3½” x 40¾” D White 1¼” Self-Drilling Stainless Steel Screw (24) H Black 1¼” Self-Drilling Stainless Steel Screw (38) I Vertical Rail (2) Picket (6) 1½” x 3½” x 18½” E .875” x 3” x 29¾” F Gate Hinge (2) J Bottom Gate Bracket (2) 4 www.zippity-outdoor.
PAGE 5
STEP 2: ASSEMBLE THE BOTTOM OF THE GATE FRAME Insert the bottom rail (F) all the way into the bottom gate bracket (E) until it hits the corner of the bracket as illustrated. STEP 2.1 E STEP 2.2 Insert the bottom rail all the way into the opposite bottom gate bracket until it hits the corner as illustrated. Note: Orient the rail with the routed holes facing up. Insert fully to this p oint. Insert F this p oint. Insert vertical rails (C) until they hit the bottom rail.
PAGE 6
STEP 3: ASSEMBLE THE GATE FRAME TOP AND ATTACH TO SIDES STEP 3.1 Insert the top rail (B) all the way into the top gate bracket (A) until it hits the corner as illustrated. STEP 3.2 A Note: Opening on top gate bracket Insert fully to this po int. Insert the top rail all the way into the opposite top gate bracket until it hits the corner as illustrated. The last routed hole on each end of the top rail should line up with the routed hole in the top rail brackets. Insert B this po 6 www.
PAGE 7
STEP 4: SCREW GATE FRAME TOGETHER STEP 4.1 Fasten gate brackets with (16) white 1¼” self-drilling stainless steel screws (G) into the pre-drilled holes on the gate brackets as necessary. G STEP 5: INSERT PICKETS INTO GATE FRAME STEP 5.1 D Insert pickets (D) through the top rail into the bottom rail. Completed gate with frame. www.zippity-outdoor.
PAGE 8
STEP 6: FASTEN GATE HINGES STEP 6.1 Fasten gate hinges (I) onto the front of the gate with (8) black 1¼” self-drilling stainless steel screws (H). H I STEP 7: POSITION, ADJUST, AND ALIGN GATE/ SECURE HINGES TO POSTS STEP 7.1 Use temporary spacers or blocks to rest the gate on during alignment and installation. 1 8 www.zippity-outdoor.com STEP 7.2 Fasten hinges to the post with (8) black 1¼” self-drilling stainless steel screws.
PAGE 9
STEP 7.3 Open the gate, and fasten the hinges to the post and inside of the gate with (16) black 1¼” self-drilling stainless steel screws. Note: If your internal pipe anchor ends up flush to the inside corner of the post, you will need to pre-drill the holes for the 1¼” self-drilling stainless steel screws to penetrate the pipe anchor. STEP 8: ALIGN AND INSTALL LATCH STEP 8.
PAGE 10
Congratulations, you are finished! 6935 Reames Rd. Ste. K. Charlotte, NC 28216 @ support@zippity-outdoor.com 704-892-5222 / 877-234-6196 zippity-outdoor.com 10 www.zippity-outdoor.