Installation Guide

ManualsBrandsZippity Outdoor Products ManualsFence Hardware36 in. x 39 in. x 1.5 in. White Vinyl Slatted Liberty Lattice Rooftop Accessory

www.zippity-outdoor.com

ASSEMBLY

INSTRUCTIONS

OPTIONAL TABLETOP KIT FOR

LIBERTY LATTICE AC SCREEN

15 MIN

approximate assembly

time for tabletop

6935 Reames Rd. Ste. K. Charlotte, NC 28216

support@zippity-outdoor.com

704-892-5222 / 877-234-6196

zippity-outdoor.com

Summary of content (6 pages)

PAGE 1
ASSEMBLY INSTRUCTIONS OPTIONAL TABLETOP KIT FOR LIBERTY LATTICE AC SCREEN 15 MIN approximate assembly time for tabletop 6935 Reames Rd. Ste. K. Charlotte, NC 28216 @ support@zippity-outdoor.com 704-892-5222 / 877-234-6196 zippity-outdoor.com www.zippity-outdoor.
PAGE 2
GENERAL INFORMATION IMPORTANT • Please read through before starting assembly. • Important: Check the inside of the larger pieces in your box for other materials packed inside. • When assembling components, place on a non-abrasive surface (i.e. shipping box) to avoid scratching. • We recommend an area approx 5’x 5’ for unobstructed assembling. • You should not need to use excessive force when assembling components.
PAGE 3
STEP 1: LAY OUT MATERIALS OPTIONAL TABLETOP KIT FOR LIBERTY LATTICE A B F Back Slat (1) 7/8” x 3” x 38 ¾” Slats (6) 7/8” x 3” x 38 ¾” Steel Screw - 1” (2) (for securing back slat) G C D Left Frame (1) / ” x 3” x 36” 78 E Right Frame (1) / ” x 3” x 36” 78 Front Frame (1) / ” x 3” x 36” 78 Steel Screw - 2.5” (4) (for connecting frame) TOOLS YOU WILL NEED Cordless Drill www.zippity-outdoor.
PAGE 4
STEP 2: INSTALLING THE BOARDS STEP 2.1 Identify the left frame (C) and lay it on a flat surface as shown. The left frame has three pre-drilled holes on the underside of the rail as shown. This side up C STEP 2.2 1. Insert the back slat (A) into the slot in the left frame under the single pre-drilled hole. 2. Drive one 1” steel screw (F) into the predrilled hole in the left frame. STEP 2.3 1. Insert six slats (B) into the holes in the left frame until they hit the back wall. 2.
PAGE 5
STEP 3: SECURING THE FRONT FRAME STEP 3.1 1. Take the front frame (E) and position it in an L-shape relative to the left frame as shown below. 2. Drive two 2.5” screws (G) into the pre-drilled holes in the side of the left frame. 1 2 E Ensure holes are facing up STEP 3.2 1 G 1. Slide the holes in the right frame (D) one by one over the slats until the right frame is in an L-shape relative to the front frame. 2. Drive a 1” screw (F) into the single pre-drilled hole in the right frame. 3. Drive two 2.
PAGE 6
STEP 4: INSTALLING THE TABLETOP STEP 4.1 1. Turn your assembled tabletop over. 2. Remove the post caps from your Liberty Lattice AC Screen Kit and insert the screen posts into the holes on the bottom of the tabletop. NOTE: Liberty Lattice AC Screen Kit is sold separately. 1 STEP 4.2 Enjoy your new tabletop! NOTE: It is recommended you distribute the weight evenly across the tabletop and not surpass a weight load of 50 lbs (23 kgs). 6935 Reames Rd. Ste. K.