PRODUCTS MANUAL R2W SERIES High Density Redundant Power Supply For 2U Chassis Rev.
INDEX 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 1.10 1.
1.1 INTRODUCTION First of all, thank you for purchasing R2W Series – High-Density Redundant power supply for 2U chassis. The R2W is a 1+1, Hot-swappable/Hot-pluggable, High-Density Redundant power supply set, it consists of: (1) complete metal frame (nickel-plated) (2) compact size (smaller than PSII form factor) 1+1 power modules (3) backplane board The R2W Series of hot swappable high-density redundant power supply offer a maximum 400/460 watts of output power.
1.2 PACKING Your R2W box package should consist of the following: (A) R2W *1 (B) Accessory pack (included 1 holding bracket for shipment)*1 (C) Products’ manual *1 1.3 MODEL DESIGNATION Model number identification: R2W – 6ZZZP R 2W 6 ZZZ P --- Redundant (AC Input) --- suit for 2U chassis (1U = 44.4 m/m) --- for 6 DC outputs (5V/12V/-5V/-12V/3.3V/5VSB) for ATX12V / EPS12V Spec. --- total output power, ZZZ- 400,460 etc. (unit: watt) --- with PFC built in (full range).
1.
INPUT CHARACTERISTICS: R2W-6400P VOLTAGE: 90 ~ 264 VAC FULL RANGE FREQUENCY : 47 ~ 63 Hz INPUT CURRENT: 8.0 / 4.0 A FOR 115 / 230 VAC INRUSH CURRENT: 60A / 80A MAX. FOR 115 / 230 VAC PER POWER MODULE OUTPUT CHARACTERISTICS: OUTPUT VOLTAGE OUTPUT CURRENT MIN.[A] MAX.[A] PEAK(A) REGULATION OUTPUT LOAD LINE RIPPLE & NOISE MAX. [P-P] 5V 3.5 26 ± 5% ± 1% 50mV 12V 2 28 ± 6% ± 1% 120mV -5V 0.05 0.7 +5/-10% ± 1% 120mV -12V 0.05 0.7 +5/-10% ± 1% 150mV 3.3V 1.
INPUT CHARACTERISTICS: R2W-6460P VOLTAGE: 90 ~ 264 VAC FULL RANGE FREQUENCY : 47 ~ 63 Hz INPUT CURRENT: 8.0 / 4.0 A FOR 115 / 230 VAC INRUSH CURRENT: 60A / 80A MAX. FOR 115 / 230 VAC PER POWER MODULE OUTPUT CHARACTERISTICS: OUTPUT VOLTAGE OUTPUT CURRENT MIN.[A] MAX.[A] PEAK(A) REGULATION OUTPUT LOAD LINE RIPPLE & NOISE MAX. [P-P] 5V 2.0 30 ± 5% ± 1% 50mV 12V 2 32 ± 5% ± 1% 120mV -5V 0.05 0.7 +5/-10% ± 1% 120mV -12V 0.05 0.7 +5/-10% ± 1% 120mV 3.3V 1.
INPUT CHARACTERISTICS: R2W-6500P VOLTAGE: 105 ~ 264 VAC FULL RANGE FREQUENCY : 47 ~ 63 Hz INPUT CURRENT: 8.0 / 4.0 A FOR 115 / 230 VAC INRUSH CURRENT: 60A / 80A MAX. FOR 115 / 230 VAC PER POWER MODULE OUTPUT CHARACTERISTICS: OUTPUT VOLTAGE OUTPUT CURRENT MIN.[A] MAX.[A] PEAK(A) REGULATION OUTPUT LOAD LINE RIPPLE & NOISE MAX. [P-P] 5V 2.0 30 ± 5% ± 1% 50mV 12V 2 32 ± 5% ± 1% 120mV -5V 0.05 0.7 +5/-10% ± 1% 120mV -12V 0.05 0.7 +5/-10% ± 1% 120mV 3.3V 1.
1.8 INSTALLATION & TESTING Turn off (Remote off) the on/off switch. Mount the power supply in the system chassis using the proper mounting tool, the mounting holes in the power supply should match those in the case. Attach the connectors to the M/B by following the M/B instructions, there are various connectors / pin-outs on both power supply and M/B. They should match each other; otherwise the connection will cause undetectable harms.
If everything works out fine, then turn off (remote off) the power system. Now put back the cover of the case and tighten with the screws that you have retained earlier. Now you have completed the installation of the R2W redundant power supply system. 1.9 HOT-SWAP PROCEDURES Please refer to the following when either power module or the fan found defective. A) Locate the defective power module by examining the individual LED (if LED without light, it indicates the power module is defective).
D) Replace a new Good power module, insert the power module into the power system to the end. E) Check the LED of the power module light Green. F) Check the LED indicating the total power system status. It should be from twinkle to Green. G) Tighten the screws of the power module to fix it. H) If you want to test this new power module in simulating defective situation. Please refer to the Section 1.8 Installation & Testing Section.
TTL signal : Sink current max. 5mA Source current max. 50uA Low Active High 1.11 --- Defective --- Normal TROUBLE SHOOTING If you have followed these directions correctly, there should be no problem occurred. Some common symptoms are: the system doesn’t work, buzzer sounds, work for a very short period, etc., please try the following steps to verify and correct it: 1. Check all the connections (correct pinouts, loose connections, wrong direction, etc). 2.
The “RELIABILITY “ solution to E-application 新巨企業股份有限公司 ZIPPY TECHNOLOGY CORP. POWER DIVISION HEADQUARTERS 10F, NO. 50, MIN CHYUAN RD., SHIN-TIEN CITY, TAIPEI HSIEN, TAIWAN, R.O.C. TEL: 886-2-29188512 WEB SITE: http://www.zippy.com.tw FAX: 886-2-29134969 E-mail：power@zippy.com.tw USA OFFICE U.S. East (Atlantic) 11 Melanie Lane, Unit 1B East Hanover, NJ 07936 TEL：1-973-463-9499 FAX：1-973-453-8014 E-mail：edward@zippy.com U.S.
