Owner's manual

ManualsBrandsZippy ManualsAccessories for electricalDMRW-6400F

1.1 INTRODUCTION

First of all, thank you for purchasing DMRW series redundant power supply.

The DMRW series is a 1+1 hot-swappable / hot-pluggable redundant power supply. It

consists of,

1) complete metal frame

2) compact size power module

3) backplane

The DMRW series hot swappable redundant power supply offer maximum

300/350/375/400 watts. The power module is in compact size, and built-in a 40mm

ball bearing DC fan for better ventilation. Each power module is designed with 6

outputs (+3.3V, +5V, +12V, -5V, -12V, and +5Vsb) circuits. All you can see on the

backplane is just passive components and this is the key point for longer MTBF.

The units also offer a warning sub-system, including LED display, buzzer alarm, TTL

signal. It guides user the fast way to find out the power supply status.

When all the power modules operate normally, it balances the load share through its

parallel design, which increases the reliability of power system.

To really discover the power system and ease in using it, we recommend you to read

through this manual carefully.

Summary of content (12 pages)

PAGE 1
.1 INTRODUCTION First of all, thank you for purchasing DMRW series redundant power supply. The DMRW series is a 1+1 hot-swappable / hot-pluggable redundant power supply. It consists of, 1) complete metal frame 2) compact size power module 3) backplane The DMRW series hot swappable redundant power supply offer maximum 300/350/375/400 watts. The power module is in compact size, and built-in a 40mm ball bearing DC fan for better ventilation. Each power module is designed with 6 outputs (+3.
PAGE 2
1.2 PACKING Your DMRW series should consist of the following, a) DMRW series x 1 b) Accessory pack x 1 c) Product Manual x 1 1.3 MODEL DESINGATION Model number identification DMRW -6zzzy MR 6 zzz y --------- mini redundant 6 output channel (+3.3V, +5V, +12V, -5V, -12V & +5Vsb) total output power, zzz –300/350 / 375 / 400 (unit: watts) P: built-in PFC (full range) 1.4 FEATURES DMRW series, 350W / 3750W / 400W, 1+1 mini redundant power supply with active PFC.
PAGE 3
DMRW series, 300W / 350W / 375W / 400W, 1+1 mini redundant power supply l l l l l l l l l l Input: -48VDC True redundant design (passive packplane) All circuit designed into the power module Hot-swap and hot-plug ability Balance load sharing design Remote sensing design Meet FCC, CISPR EMI regulation Faulty free- slide rail design Isolated fence design to meet safety regulation Compact size (PS2 form factor) 1.
PAGE 4
PAGE 5
1.6 SPECIFICATION INPUT CHARACTERISTICS: DMRW-6300F l VOLTAGE ： DC －36V∼－72V l INPUT CURRENT：10.0A (RMS) FOR －48 VDC l INRUSH CURRENT：20.0A MAX. OUTPUT CHARACTERISTICS： OUTPUT CURRENT OUTPUT VOLTAGE MIN MAX +5V 3A -5V PEAK OUTPUT REGULATION RIPPLE &NOISE LOAD LINE 30A ±5% ±1% 50mV 0.1A 0.5A ±6% ±1% 120mV +12V 2.5A 20A ±10% ±1% 120mV -12V 0.1A 1.2A ±10% ±1% 150mV +3.3V 1A 20A ±5% ±1% 50mV +5VSB 0.1A 2.0A ±5% ±1% 50mV MAX.
PAGE 6
INPUT CHARACTERISTICS: DMRW-6350F l VOLTAGE ： DC －36V∼－72V l INPUT CURRENT：10.0A (RMS) FOR －48 VDC l INRUSH CURRENT：20.0A MAX. OUTPUT CHARACTERISTICS: OUTPUT VOLTAGE OUTPUT CURRENT MIN. MAX. PEAK REGULATION LOAD LINE OUTPUT RIPPLE &NOISE MAX. [P-P] +5V 3A 32A ±5% ±1% 50mV -5V 0.1A 0.5A ±6% ±1% 120mV +12V 2.5A 25A ±10% ±1% 120mV -12V 0.1A 1.2A ±10% ±1% 150mV +3.3V 1A 25A ±5% ±1% 50mV +5VSB 0.1A 2.0A ±5% ±1% 50mV REMARK: TOTAL CURRENT OF +5V AND +3.
PAGE 7
INPUT CHARACTERISTICS: DMRW-6375F l VOLTAGE ： DC －36V∼－72V l INPUT CURRENT：11.0A (RMS) FOR －48 VDC l INRUSH CURRENT：20.0A MAX. OUTPUT CHARACTERISTICS: OUTPUT CURRENT OUTPUT VOLTAGE MIN. MAX. PEAK REGULATION LOAD LINE OUTPUT RIPPLE &NOISE MAX. [P-P] +5V 3A 32A ±5% ±1% 50mV -5V 0.1A 0.5A ±6% ±1% 120mV +12V 2.5A 25A ±10% ±1% 120mV -12V 0.1A 1.2A ±10% ±1% 150mV +3.3V 1A 25A ±5% ±1% 50mV +5VSB 0.1A 2.0A ±5% ±1% 50mV REMARK: TOTAL CURRENT OF +5V AND +3.
PAGE 8
INPUT CHARACTERISTICS: DMRW-6400F l VOLTAGE ： DC －40V∼－72V l INPUT CURRENT：12.0A (RMS) FOR －48 VDC l INRUSH CURRENT：20.0A MAX. OUTPUT CHARACTERISTICS: OUTPUT CURRENT OUTPUT VOLTAGE MIN. MAX. PEAK REGULATION LOAD LINE OUTPUT RIPPLE &NOISE MAX. [P-P] +5V 3A 32A ±5% ±1% 50mV -5V 0.1A 0.5A ±6% ±1% 120mV +12V 2.5A 25A ±10% ±1% 120mV -12V 0.1A 1.2A ±10% ±1% 150mV +3.3V 1A 25A ±5% ±1% 50mV +5VSB 0.1A 2.0A ±5% ±1% 50mV REMARK: TOTAL CURRENT OF +5V AND +3.
PAGE 9
1.7 INSTALLATION & TESTING Mount the power supply into the system chassis by using proper mounting tool. The mounting holes of the power supply should match up with those in the chassis. Connect the power connectors to the M/B by following the M/B instruction. There is various on connectors / pinouts in both power supply and M/B. Please ensure to connect the matched one; otherwise, it will cause unexpected harms. Connect the remaining power connectors to the various peripherals as needed.
PAGE 10
1.8 Hot-swap procedures Please refer to the following when either power module is defective. 1) Locate the defective power module by examining the individual LED (if LED is distinguished, it indicates the power module is defective). *** WARNING: Please perform the following step carefully; otherwise, it may cause the whole system shutdown. *** WARNING: Please do not remove the defective power module until you have worn gloves to keep from been burned.
PAGE 11
THE LED CONNECTOR OF TOTAL POWER SYSTEM PIN# 1 COLOR RED 2 BLACK 3 GREEN THE BUZZER RESET SWITCH CONNECTOR PIN# COLOR 1 2 BLACK YELLOW THE SIGNAL CONNECTOR OF POWER RESET PIN# COLOR COLOR 1 RED TTL SIGNAL 2 BLACK GND TTL signal: Sink current max. 5mA Source current max. 50uA Low Active ---Defective High ---Normal 1.10 TROUBLE SHOOTING If you have followed these instructions correctly, it should function normally.
PAGE 12
3) Once you hear the buzzer sound or see the warning LED in RED, please check, a) If the loading is under the minimum or over the maximum load of each channel. b) If the power source is well connected and supplied. Shall the above condition is happened, please disconnect the power source and wait for 2-3 minutes to release the protection status; then test it again. c) If buzzer keeps alarming or LED indicates the power module failure, please locate which power module is defective.